Yesterday I got a error message telling me that "Device: /dev/sdi [SAT], ATA error count increased from 0 to 1."
I did some research and it sounds like ATA errors might happen due to different reasons depending on SMART result.
I do not know how to read the SMART results, and I just want to double check if this happened because my drive is bad(maybe too old?).
Please help!
I did some research and it sounds like ATA errors might happen due to different reasons depending on SMART result.
I do not know how to read the SMART results, and I just want to double check if this happened because my drive is bad(maybe too old?).
Please help!
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.142+truenas] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD80EFAX-68KNBN0
Serial Number: VGJL11RG
LU WWN Device Id: 5 000cca 0bee461a6
Firmware Version: 81.00A81
User Capacity: 8,001,563,222,016 bytes [8.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Dec 11 05:08:27 2022 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 87) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 877) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0004 127 127 054 Old_age Offline - 112
3 Spin_Up_Time 0x0007 154 154 024 Pre-fail Always - 528 (Average 529)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 46
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000a 100 100 067 Old_age Always - 0
8 Seek_Time_Performance 0x0004 128 128 020 Old_age Offline - 18
9 Power_On_Hours 0x0012 099 099 000 Old_age Always - 13940
10 Spin_Retry_Count 0x0012 100 100 060 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 43
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 620
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 620
194 Temperature_Celsius 0x0002 203 203 000 Old_age Always - 32 (Min/Max 21/72)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 1
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 13936 hours (580 days + 16 hours)
When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 43 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 48 00 d6 5b 40 08 1d+08:33:36.430 READ FPDMA QUEUED
60 00 90 40 a1 28 40 08 1d+08:33:36.355 READ FPDMA QUEUED
60 00 88 40 74 16 40 08 1d+08:33:36.355 READ FPDMA QUEUED
60 00 80 40 6c 16 40 08 1d+08:33:36.355 READ FPDMA QUEUED
60 00 78 40 63 16 40 08 1d+08:33:36.355 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 13842 -
# 2 Short offline Completed without error 00% 676 -
# 3 Short offline Completed without error 00% 652 -
# 4 Short offline Completed without error 00% 628 -
# 5 Short offline Completed without error 00% 604 -
# 6 Short offline Completed without error 00% 580 -
# 7 Short offline Completed without error 00% 556 -
# 8 Short offline Completed without error 00% 532 -
# 9 Short offline Completed without error 00% 508 -
#10 Short offline Completed without error 00% 484 -
#11 Short offline Completed without error 00% 460 -
#12 Short offline Completed without error 00% 212 -
#13 Short offline Completed without error 00% 188 -
#14 Short offline Completed without error 00% 164 -
#15 Short offline Completed without error 00% 157 -
#16 Short offline Completed without error 00% 151 -
#17 Short offline Completed without error 00% 140 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.