SATA controller swap

Status
Not open for further replies.
B

bobb

Dabbler
Joined
Nov 26, 2016
Messages
19
Hey guys,
I'm using the SATA ports on my Supermicro board right now. I've been getting errors like

Code:
Device: /dev/ada4, 1 Currently unreadable (pending) sectors
Device: /dev/ada4, Self-Test Log error count increased from 6 to 7
Device: /dev/ada2, ATA error count increased from 10 to 15
Device: /dev/ada2, 1 Currently unreadable (pending) sectors


ever since I upgraded my system to a 6 drive system a few months ago. It was running on 5 drives before.
AFAIK this problem doesn't have to be drive related, but could also be controller/cable related.
Therefore I decided to buy an IBM M1115 controller and miniSAS to SATA cables.

Now my question:
Do I have to unmount/mount the drives anywhere in the FreeNAS UI or via command line in order to perform the upgrade or can I simply shut the system down, pull the cables out of the motherboard, and plug them into the IBM controller?
This is assuming I've already flashed the controller to IT firmware.

Regards, bobb
 
Bidule0hm

Bidule0hm

Server Electronics Sorcerer
Joined
Aug 5, 2013
Messages
3,710
No need to do anything besides swapping the drives ;)

And this drive has one pending sector which means you should keep an eye on it. Are the SMART tests correctly configured?
 
Last edited:
B

bobb

Dabbler
Joined
Nov 26, 2016
Messages
19
Robert Trevellyan said:
This implies repeated SMART test failures. Please post (between CODE tags) the output of smartctl -x for the drive.
Click to expand...

I'm out of town until Thursday, so this will have to wait a few days. But thanks in advance!
 
B

bobb

Dabbler
Joined
Nov 26, 2016
Messages
19
Robert Trevellyan said:
This implies repeated SMART test failures. Please post (between CODE tags) the output of smartctl -x for the drive.
Click to expand...

Thank you for helping me! Here's the output:

Code:
-x /dev/ada2
smartctl 6.5 2016-05-07 r4318 [FreeBSD 10.3-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:	 Western Digital Red
Device Model:	 WDC WD30EFRX-68EUZN0
Serial Number:	***
LU WWN Device Id: ***
Firmware Version: 82.00A82
User Capacity:	3,000,592,982,016 bytes [3.00 TB]
Sector Sizes:	 512 bytes logical, 4096 bytes physical
Rotation Rate:	5400 rpm
Device is:		In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:	Fri Dec  2 14:50:57 2016 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:	  (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection:		 (39840) seconds.
Offline data collection
capabilities:			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:			(0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:		(0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time:	 (   2) minutes.
Extended self-test routine
recommended polling time:	 ( 399) minutes.
Conveyance self-test routine
recommended polling time:	 (   5) minutes.
SCT capabilities:			(0x703d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME		  FLAGS	VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate	 POSR-K   200   200   051	-	198
  3 Spin_Up_Time			POS--K   181   181   021	-	5933
  4 Start_Stop_Count		-O--CK   100   100   000	-	9
  5 Reallocated_Sector_Ct   PO--CK   200   200   140	-	0
  7 Seek_Error_Rate		 -OSR-K   200   200   000	-	0
  9 Power_On_Hours		  -O--CK   086   086   000	-	10685
 10 Spin_Retry_Count		-O--CK   100   253   000	-	0
 11 Calibration_Retry_Count -O--CK   100   253   000	-	0
 12 Power_Cycle_Count	   -O--CK   100   100   000	-	9
192 Power-Off_Retract_Count -O--CK   200   200   000	-	2
193 Load_Cycle_Count		-O--CK   200   200   000	-	159
194 Temperature_Celsius	 -O---K   124   112   000	-	26
196 Reallocated_Event_Count -O--CK   200   200   000	-	0
197 Current_Pending_Sector  -O--CK   200   200   000	-	1
198 Offline_Uncorrectable   ----CK   100   253   000	-	0
199 UDMA_CRC_Error_Count	-O--CK   200   200   000	-	0
200 Multi_Zone_Error_Rate   ---R--   100   253   000	-	0
							||||||_ K auto-keep
							|||||__ C event count
							||||___ R error rate
							|||____ S speed/performance
							||_____ O updated online
							|______ P prefailure warning

General Purpose Log Directory Version 1
SMART		   Log Directory Version 1 [multi-sector log support]
Address	Access  R/W   Size  Description
0x00	   GPL,SL  R/O	  1  Log Directory
0x01		   SL  R/O	  1  Summary SMART error log
0x02		   SL  R/O	  5  Comprehensive SMART error log
0x03	   GPL	 R/O	  6  Ext. Comprehensive SMART error log
0x06		   SL  R/O	  1  SMART self-test log
0x07	   GPL	 R/O	  1  Extended self-test log
0x09		   SL  R/W	  1  Selective self-test log
0x10	   GPL	 R/O	  1  SATA NCQ Queued Error log
0x11	   GPL	 R/O	  1  SATA Phy Event Counters log
0x21	   GPL	 R/O	  1  Write stream error log
0x22	   GPL	 R/O	  1  Read stream error log
0x80-0x9f  GPL,SL  R/W	 16  Host vendor specific log
0xa0-0xa7  GPL,SL  VS	  16  Device vendor specific log
0xa8-0xb7  GPL,SL  VS	   1  Device vendor specific log
0xbd	   GPL,SL  VS	   1  Device vendor specific log
0xc0	   GPL,SL  VS	   1  Device vendor specific log
0xc1	   GPL	 VS	  93  Device vendor specific log
0xe0	   GPL,SL  R/W	  1  SCT Command/Status
0xe1	   GPL,SL  R/W	  1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 193 (device log contains only the most recent 24 errors)
	CR	 = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH	 = LBA High (was: Cylinder High) Register	]   LBA
	LM	 = LBA Mid (was: Cylinder Low) Register	  ] Register
	LL	 = LBA Low (was: Sector Number) Register	 ]
	DV	 = Device (was: Device/Head) Register
	DC	 = Device Control Register
	ER	 = Error register
	ST	 = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 193 [0] occurred at disk power-on lifetime: 10618 hours (442 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 02 c9 f0 c0 40 00  Error: UNC at LBA = 0x02c9f0c0 = 46788800

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 a0 00 00 02 c9 f1 b8 40 08 36d+11:36:04.565  READ FPDMA QUEUED
  60 01 00 00 98 00 00 02 c9 f0 b8 40 08 36d+11:36:04.565  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 40 08 36d+11:36:04.561  READ LOG EXT
  60 01 00 00 88 00 00 02 c9 f1 b8 40 08 36d+11:36:01.070  READ FPDMA QUEUED
  60 01 00 00 80 00 00 02 c9 f0 b8 40 08 36d+11:36:01.070  READ FPDMA QUEUED

Error 192 [23] occurred at disk power-on lifetime: 10618 hours (442 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 02 c9 f0 c0 40 00  Error: UNC at LBA = 0x02c9f0c0 = 46788800

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 88 00 00 02 c9 f1 b8 40 08 36d+11:36:01.070  READ FPDMA QUEUED
  60 01 00 00 80 00 00 02 c9 f0 b8 40 08 36d+11:36:01.070  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 40 08 36d+11:36:01.065  READ LOG EXT
  60 01 00 00 70 00 00 02 c9 f1 b8 40 08 36d+11:35:57.583  READ FPDMA QUEUED
  60 01 00 00 68 00 00 02 c9 f0 b8 40 08 36d+11:35:57.583  READ FPDMA QUEUED

Error 191 [22] occurred at disk power-on lifetime: 10618 hours (442 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 02 c9 f0 c0 40 00  Error: UNC at LBA = 0x02c9f0c0 = 46788800

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 70 00 00 02 c9 f1 b8 40 08 36d+11:35:57.583  READ FPDMA QUEUED
  60 01 00 00 68 00 00 02 c9 f0 b8 40 08 36d+11:35:57.583  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 40 08 36d+11:35:57.579  READ LOG EXT
  60 01 00 00 58 00 00 02 c9 f1 b8 40 08 36d+11:35:54.088  READ FPDMA QUEUED
  60 01 00 00 50 00 00 02 c9 f0 b8 40 08 36d+11:35:54.088  READ FPDMA QUEUED

Error 190 [21] occurred at disk power-on lifetime: 10618 hours (442 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 02 c9 f0 c0 40 00  Error: UNC at LBA = 0x02c9f0c0 = 46788800

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 58 00 00 02 c9 f1 b8 40 08 36d+11:35:54.088  READ FPDMA QUEUED
  60 01 00 00 50 00 00 02 c9 f0 b8 40 08 36d+11:35:54.088  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 40 08 36d+11:35:54.083  READ LOG EXT
  60 01 00 00 40 00 00 02 c9 f1 b8 40 08 36d+11:35:50.607  READ FPDMA QUEUED
  60 01 00 00 38 00 00 02 c9 f0 b8 40 08 36d+11:35:50.606  READ FPDMA QUEUED

Error 189 [20] occurred at disk power-on lifetime: 10618 hours (442 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 02 c9 f0 c0 40 00  Error: UNC at LBA = 0x02c9f0c0 = 46788800

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 40 00 00 02 c9 f1 b8 40 08 36d+11:35:50.607  READ FPDMA QUEUED
  60 01 00 00 38 00 00 02 c9 f0 b8 40 08 36d+11:35:50.606  READ FPDMA QUEUED
  60 01 00 00 30 00 00 02 c9 ef b8 40 08 36d+11:35:50.492  READ FPDMA QUEUED
  60 01 00 00 28 00 00 02 c9 ee b8 40 08 36d+11:35:50.492  READ FPDMA QUEUED
  60 00 c8 00 20 00 00 02 c9 ed f0 40 08 36d+11:35:50.491  READ FPDMA QUEUED

Error 188 [19] occurred at disk power-on lifetime: 10618 hours (442 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 02 c9 e4 80 42 00  Error: UNC at LBA = 0x02c9e480 = 46785664

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 00 00 00 02 c9 e4 30 42 08 36d+11:35:45.078  READ DMA
  c8 00 00 00 00 00 00 02 c9 e4 30 42 08 36d+11:35:41.682  READ DMA
  c8 00 00 00 00 00 00 02 c9 e4 30 42 08 36d+11:35:38.285  READ DMA
  c8 00 00 00 00 00 00 02 c9 e4 30 42 08 36d+11:35:34.911  READ DMA
  c8 00 00 00 00 00 00 02 c9 e4 30 42 08 36d+11:35:31.549  READ DMA

Error 187 [18] occurred at disk power-on lifetime: 10618 hours (442 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 02 c9 e4 80 42 00  Error: UNC at LBA = 0x02c9e480 = 46785664

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 00 00 00 02 c9 e4 30 42 08 36d+11:35:41.682  READ DMA
  c8 00 00 00 00 00 00 02 c9 e4 30 42 08 36d+11:35:38.285  READ DMA
  c8 00 00 00 00 00 00 02 c9 e4 30 42 08 36d+11:35:34.911  READ DMA
  c8 00 00 00 00 00 00 02 c9 e4 30 42 08 36d+11:35:31.549  READ DMA
  60 01 00 00 50 00 00 02 c9 e3 30 40 08 36d+11:35:31.532  READ FPDMA QUEUED

Error 186 [17] occurred at disk power-on lifetime: 10618 hours (442 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 02 c9 e4 80 42 00  Error: UNC at LBA = 0x02c9e480 = 46785664

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 00 00 00 02 c9 e4 30 42 08 36d+11:35:38.285  READ DMA
  c8 00 00 00 00 00 00 02 c9 e4 30 42 08 36d+11:35:34.911  READ DMA
  c8 00 00 00 00 00 00 02 c9 e4 30 42 08 36d+11:35:31.549  READ DMA
  60 01 00 00 50 00 00 02 c9 e3 30 40 08 36d+11:35:31.532  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 40 08 36d+11:35:31.528  READ LOG EXT

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
	1		0		0  Not_testing
	2		0		0  Not_testing
	3		0		0  Not_testing
	4		0		0  Not_testing
	5		0		0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:				  3
SCT Version (vendor specific):	   258 (0x0102)
SCT Support Level:				   1
Device State:						Active (0)
Current Temperature:					26 Celsius
Power Cycle Min/Max Temperature:	 19/27 Celsius
Lifetime	Min/Max Temperature:	  2/38 Celsius
Under/Over Temperature Limit Count:   0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version:	 2
Temperature Sampling Period:		 1 minute
Temperature Logging Interval:		1 minute
Min/Max recommended Temperature:	  0/60 Celsius
Min/Max Temperature Limit:		   -41/85 Celsius
Temperature History Size (Index):	478 (148)

Index	Estimated Time   Temperature Celsius
 149	2016-12-02 06:53	26  *******
 ...	..(476 skipped).	..  *******
 148	2016-12-02 14:50	26  *******

SCT Error Recovery Control:
		   Read:	 70 (7.0 seconds)
		  Write:	 70 (7.0 seconds)

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID	  Size	 Value  Description
0x0001  2			0  Command failed due to ICRC error
0x0002  2			0  R_ERR response for data FIS
0x0003  2			0  R_ERR response for device-to-host data FIS
0x0004  2			0  R_ERR response for host-to-device data FIS
0x0005  2			0  R_ERR response for non-data FIS
0x0006  2			0  R_ERR response for device-to-host non-data FIS
0x0007  2			0  R_ERR response for host-to-device non-data FIS
0x0008  2			0  Device-to-host non-data FIS retries
0x0009  2			2  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2			3  Device-to-host register FISes sent due to a COMRESET
0x000b  2			0  CRC errors within host-to-device FIS
0x000f  2			0  R_ERR response for host-to-device data FIS, CRC
0x0012  2			0  R_ERR response for host-to-device non-data FIS, CRC
0x8000  4	   147205  Vendor specific
 
B

bobb

Dabbler
Joined
Nov 26, 2016
Messages
19
Here's the output of ada4:

Code:
smartctl -x /dev/ada4
smartctl 6.5 2016-05-07 r4318 [FreeBSD 10.3-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:	 Western Digital Red
Device Model:	 WDC WD30EFRX-68EUZN0
Serial Number:	***
LU WWN Device Id: ***
Firmware Version: 82.00A82
User Capacity:	3,000,592,982,016 bytes [3.00 TB]
Sector Sizes:	 512 bytes logical, 4096 bytes physical
Rotation Rate:	5400 rpm
Device is:		In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:	Fri Dec  2 14:50:06 2016 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:	  (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection:		 (39120) seconds.
Offline data collection
capabilities:			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:			(0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:		(0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time:	 (   2) minutes.
Extended self-test routine
recommended polling time:	 ( 393) minutes.
Conveyance self-test routine
recommended polling time:	 (   5) minutes.
SCT capabilities:		   (0x703d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME		  FLAGS	VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate	 POSR-K   200   200   051	-	22
  3 Spin_Up_Time			POS--K   181   180   021	-	5916
  4 Start_Stop_Count		-O--CK   100   100   000	-	58
  5 Reallocated_Sector_Ct   PO--CK   200   200   140	-	0
  7 Seek_Error_Rate		 -OSR-K   200   200   000	-	0
  9 Power_On_Hours		  -O--CK   079   079   000	-	15518
 10 Spin_Retry_Count		-O--CK   100   253   000	-	0
 11 Calibration_Retry_Count -O--CK   100   253   000	-	0
 12 Power_Cycle_Count	   -O--CK   100   100   000	-	58
192 Power-Off_Retract_Count -O--CK   200   200   000	-	21
193 Load_Cycle_Count		-O--CK   200   200   000	-	2801
194 Temperature_Celsius	 -O---K   125   109   000	-	25
196 Reallocated_Event_Count -O--CK   200   200   000	-	0
197 Current_Pending_Sector  -O--CK   200   200   000	-	1
198 Offline_Uncorrectable   ----CK   100   253   000	-	0
199 UDMA_CRC_Error_Count	-O--CK   200   200   000	-	0
200 Multi_Zone_Error_Rate   ---R--   100   253   000	-	0
							||||||_ K auto-keep
							|||||__ C event count
							||||___ R error rate
							|||____ S speed/performance
							||_____ O updated online
							|______ P prefailure warning

General Purpose Log Directory Version 1
SMART		   Log Directory Version 1 [multi-sector log support]
Address	Access  R/W   Size  Description
0x00	   GPL,SL  R/O	  1  Log Directory
0x01		   SL  R/O	  1  Summary SMART error log
0x02		   SL  R/O	  5  Comprehensive SMART error log
0x03	   GPL	 R/O	  6  Ext. Comprehensive SMART error log
0x06		   SL  R/O	  1  SMART self-test log
0x07	   GPL	 R/O	  1  Extended self-test log
0x09		   SL  R/W	  1  Selective self-test log
0x10	   GPL	 R/O	  1  SATA NCQ Queued Error log
0x11	   GPL	 R/O	  1  SATA Phy Event Counters log
0x21	   GPL	 R/O	  1  Write stream error log
0x22	   GPL	 R/O	  1  Read stream error log
0x80-0x9f  GPL,SL  R/W	 16  Host vendor specific log
0xa0-0xa7  GPL,SL  VS	  16  Device vendor specific log
0xa8-0xb7  GPL,SL  VS	   1  Device vendor specific log
0xbd	   GPL,SL  VS	   1  Device vendor specific log
0xc0	   GPL,SL  VS	   1  Device vendor specific log
0xc1	   GPL	 VS	  93  Device vendor specific log
0xe0	   GPL,SL  R/W	  1  SCT Command/Status
0xe1	   GPL,SL  R/W	  1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 16
	CR	 = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH	 = LBA High (was: Cylinder High) Register	]   LBA
	LM	 = LBA Mid (was: Cylinder Low) Register	  ] Register
	LL	 = LBA Low (was: Sector Number) Register	 ]
	DV	 = Device (was: Device/Head) Register
	DC	 = Device Control Register
	ER	 = Error register
	ST	 = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 16 [15] occurred at disk power-on lifetime: 15451 hours (643 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 e1 65 88 40 00  Error: UNC at LBA = 0x00e16588 = 14771592

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 10 00 00 00 e1 65 b0 40 08 36d+11:31:18.722  READ FPDMA QUEUED
  60 01 00 00 08 00 00 00 e1 64 b0 40 08 36d+11:31:18.721  READ FPDMA QUEUED
  60 01 00 00 00 00 00 00 e1 63 b0 40 08 36d+11:31:18.721  READ FPDMA QUEUED
  60 01 00 00 f8 00 00 00 e1 62 b0 40 08 36d+11:31:18.720  READ FPDMA QUEUED
  60 01 00 00 f0 00 00 00 e1 61 b0 40 08 36d+11:31:18.720  READ FPDMA QUEUED

Error 15 [14] occurred at disk power-on lifetime: 14603 hours (608 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 e1 73 00 40 00  Error: UNC at LBA = 0x00e17300 = 14775040

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 10 00 00 00 e1 73 78 40 08  1d+03:43:00.663  READ FPDMA QUEUED
  60 01 00 00 08 00 00 00 e1 72 78 40 08  1d+03:43:00.663  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 40 08  1d+03:43:00.658  READ LOG EXT
  60 01 00 00 f8 00 00 00 e1 73 78 40 08  1d+03:42:57.176  READ FPDMA QUEUED
  60 01 00 00 f0 00 00 00 e1 72 78 40 08  1d+03:42:57.176  READ FPDMA QUEUED

Error 14 [13] occurred at disk power-on lifetime: 14603 hours (608 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 e1 73 00 40 00  Error: UNC at LBA = 0x00e17300 = 14775040

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 f8 00 00 00 e1 73 78 40 08  1d+03:42:57.176  READ FPDMA QUEUED
  60 01 00 00 f0 00 00 00 e1 72 78 40 08  1d+03:42:57.176  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 40 08  1d+03:42:57.173  READ LOG EXT
  60 01 00 00 e0 00 00 00 e1 73 78 40 08  1d+03:42:53.681  READ FPDMA QUEUED
  60 01 00 00 d8 00 00 00 e1 72 78 40 08  1d+03:42:53.681  READ FPDMA QUEUED

Error 13 [12] occurred at disk power-on lifetime: 14603 hours (608 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 e1 73 00 40 00  Error: UNC at LBA = 0x00e17300 = 14775040

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 e0 00 00 00 e1 73 78 40 08  1d+03:42:53.681  READ FPDMA QUEUED
  60 01 00 00 d8 00 00 00 e1 72 78 40 08  1d+03:42:53.681  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 40 08  1d+03:42:53.676  READ LOG EXT
  60 01 00 00 c8 00 00 00 e1 73 78 40 08  1d+03:42:50.195  READ FPDMA QUEUED
  60 01 00 00 c0 00 00 00 e1 72 78 40 08  1d+03:42:50.195  READ FPDMA QUEUED

Error 12 [11] occurred at disk power-on lifetime: 14603 hours (608 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 e1 73 00 40 00  Error: UNC at LBA = 0x00e17300 = 14775040

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 c8 00 00 00 e1 73 78 40 08  1d+03:42:50.195  READ FPDMA QUEUED
  60 01 00 00 c0 00 00 00 e1 72 78 40 08  1d+03:42:50.195  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 40 08  1d+03:42:50.191  READ LOG EXT
  60 01 00 00 b0 00 00 00 e1 73 78 40 08  1d+03:42:46.714  READ FPDMA QUEUED
  60 01 00 00 a8 00 00 00 e1 72 78 40 08  1d+03:42:46.714  READ FPDMA QUEUED

Error 11 [10] occurred at disk power-on lifetime: 14603 hours (608 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 e1 73 00 40 00  Error: UNC at LBA = 0x00e17300 = 14775040

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 b0 00 00 00 e1 73 78 40 08  1d+03:42:46.714  READ FPDMA QUEUED
  60 01 00 00 a8 00 00 00 e1 72 78 40 08  1d+03:42:46.714  READ FPDMA QUEUED
  60 01 00 00 a0 00 00 00 e1 71 78 40 08  1d+03:42:46.713  READ FPDMA QUEUED
  60 01 00 00 98 00 00 00 e1 70 78 40 08  1d+03:42:46.713  READ FPDMA QUEUED
  60 01 00 00 90 00 00 00 e1 6f 78 40 08  1d+03:42:46.712  READ FPDMA QUEUED

Error 10 [9] occurred at disk power-on lifetime: 14603 hours (608 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 e1 59 28 40 00  Error: UNC at LBA = 0x00e15928 = 14768424

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 d0 00 00 00 e1 58 f0 40 08  1d+03:42:41.337  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 40 08  1d+03:42:41.333  READ LOG EXT
  60 01 00 00 c0 00 00 00 e1 58 f0 40 08  1d+03:42:37.851  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 40 08  1d+03:42:37.848  READ LOG EXT
  60 01 00 00 b0 00 00 00 e1 58 f0 40 08  1d+03:42:34.366  READ FPDMA QUEUED

Error 9 [8] occurred at disk power-on lifetime: 14603 hours (608 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 e1 59 28 40 00  Error: UNC at LBA = 0x00e15928 = 14768424

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 c0 00 00 00 e1 58 f0 40 08  1d+03:42:37.851  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 40 08  1d+03:42:37.848  READ LOG EXT
  60 01 00 00 b0 00 00 00 e1 58 f0 40 08  1d+03:42:34.366  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 40 08  1d+03:42:34.362  READ LOG EXT
  60 01 00 00 a0 00 00 00 e1 58 f0 40 08  1d+03:42:30.881  READ FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description	Status				  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline	   Completed: read failure	   10%	 15425		 14771592
# 2  Short offline	   Completed without error	   00%	 15257		 -
# 3  Short offline	   Completed without error	   00%	 15089		 -
# 4  Short offline	   Completed: read failure	   10%	 14920		 14771592
# 5  Short offline	   Completed without error	   00%	 14753		 -
# 6  Short offline	   Completed: read failure	   20%	 14585		 14768152
# 7  Short offline	   Completed: read failure	   20%	 14417		 14768152
# 8  Short offline	   Completed: read failure	   20%	 14249		 14768152
# 9  Short offline	   Completed: read failure	   20%	 14081		 14768152
#10  Short offline	   Completed: read failure	   20%	 13913		 14768152
#11  Short offline	   Completed without error	   00%	 13746		 -
#12  Short offline	   Completed without error	   00%	 13578		 -
#13  Short offline	   Completed without error	   00%	 13410		 -
#14  Short offline	   Completed without error	   00%	 13242		 -
#15  Short offline	   Completed without error	   00%	 13074		 -
#16  Short offline	   Completed without error	   00%	 12907		 -
#17  Short offline	   Completed without error	   00%	 12739		 -
#18  Short offline	   Completed without error	   00%	 12571		 -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
	1		0		0  Not_testing
	2		0		0  Not_testing
	3		0		0  Not_testing
	4		0		0  Not_testing
	5		0		0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:				  3
SCT Version (vendor specific):	   258 (0x0102)
SCT Support Level:				   1
Device State:						Active (0)
Current Temperature:					25 Celsius
Power Cycle Min/Max Temperature:	 19/25 Celsius
Lifetime	Min/Max Temperature:	  2/41 Celsius
Under/Over Temperature Limit Count:   0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version:	 2
Temperature Sampling Period:		 1 minute
Temperature Logging Interval:		1 minute
Min/Max recommended Temperature:	  0/60 Celsius
Min/Max Temperature Limit:		   -41/85 Celsius
Temperature History Size (Index):	478 (268)

Index	Estimated Time   Temperature Celsius
 269	2016-12-02 06:53	25  ******
 ...	..(476 skipped).	..  ******
 268	2016-12-02 14:50	25  ******

SCT Error Recovery Control:
		   Read:	 70 (7.0 seconds)
		  Write:	 70 (7.0 seconds)

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID	  Size	 Value  Description
0x0001  2			0  Command failed due to ICRC error
0x0002  2			0  R_ERR response for data FIS
0x0003  2			0  R_ERR response for device-to-host data FIS
0x0004  2			0  R_ERR response for host-to-device data FIS
0x0005  2			0  R_ERR response for non-data FIS
0x0006  2			0  R_ERR response for device-to-host non-data FIS
0x0007  2			0  R_ERR response for host-to-device non-data FIS
0x0008  2			0  Device-to-host non-data FIS retries
0x0009  2			2  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2			3  Device-to-host register FISes sent due to a COMRESET
0x000b  2			0  CRC errors within host-to-device FIS
0x000f  2			0  R_ERR response for host-to-device data FIS, CRC
0x0012  2			0  R_ERR response for host-to-device non-data FIS, CRC
0x8000  4	   147154  Vendor specific
 
R

Robert Trevellyan

Pony Wrangler
Joined
May 16, 2014
Messages
3,778
ada2 has never had a SMART test, but has one pending reallocation. Fix your SMART test schedule and keep a close eye on it.

ada4 started failing SMART tests about 2 months ago. If it's still under warranty (it should be), you have grounds for an RMA. Some people prefer to try to force reallocation of bad sectors. If you want to try this, one approach is to remove it and run badblocks destructive write test on it.
 
B

bobb

Dabbler
Joined
Nov 26, 2016
Messages
19
Robert Trevellyan said:
ada2 has never had a SMART test, but has one pending reallocation. Fix your SMART test schedule and keep a close eye on it.

ada4 started failing SMART tests about 2 months ago. If it's still under warranty (it should be), you have grounds for an RMA. Some people prefer to try to force reallocation of bad sectors. If you want to try this, one approach is to remove it and run badblocks destructive write test on it.
Click to expand...

I have swapped ada4 earlier this month. I also dropped the M1115 into my rig. Resilvering completed without any errors, and after I installed the M1115, the FreeNAS GUI and E-Mail errors also went away. I did adjust the SMART test schedule after replacing ada4 and installing the HBA.
Now it looks like ada2 (now called da3 since I replaced the HBA) just failed a few hours ago. Guess it's time for another RMA.
 
Last edited by a moderator:
Status
Not open for further replies.

Important Announcement for the TrueNAS Community.

The TrueNAS Community has now been moved. This forum will now become READ-ONLY for historical purposes. Please feel free to join us on the new TrueNAS Community Forums.

Related topics on forums.truenas.com for thread: "SATA controller swap"

Similar threads

P
  • Locked
Please help which disk is bad
2
Replies
25
Views
6K
Bidule0hm
Bidule0hm
Y
  • Locked
smartd warning
Replies
2
Views
1K
Youri Andropov
Y
J
  • Locked
Defective hard disk ?
2
Replies
31
Views
9K
paleoN
paleoN
M
  • Locked
Currently unreadable (pending) sectors
Replies
8
Views
2K
danb35
danb35
D
  • Locked
8.3.1 - panic and stopped
Replies
3
Views
1K
cyberjock
C
Top