1) build new system, connect WD RED 4TB hard disks to X9SRL onboard SATA ports (I need to flash & install my 9211's yet)
2) boot from ultimate bootCD, run memtest+, 4 passes/24 hours clean.
6) run smartctl -t short /dev/ada0 (in parallel ada1, ada2 & ada3, da0,da1,da2, da3) = ALL CLEAR
7) run smartctl -t conveyance /dev/ada0 (in parallel ada1, ada2 & ada3, da0,da1,da2, da3) = ALL CLEAR
8) run smartctl -t long /dev/ada0 (in parallel ada1, ada2 & ada3, da0,da1,da2, da3) = ALL CLEAR
9) run badblocks -ws /dev/ada0 (in parallel ada1, ada2 & ada3, da0,da1,da2, da3) = ERRORS
smartctl output of ada2 for you......it looks like there is some DMA issues causing hiccups.....can you help me understand how to resolve?
[admin@freenas] /% sudo smartctl -a /dev/ada2
Password:
smartctl 6.2 2013-07-26 r3841 [FreeBSD 9.2-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: WDC WD40EFRX-68WT0N0
Serial Number: WD-WCC4ENZ18WVP
LU WWN Device Id: 5 0014ee 25fb99d2e
Firmware Version: 80.00A80
User Capacity: 4,000,787,030,016 bytes [4.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon Sep 1 08:04:38 2014 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (52860) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 529) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 100 253 021 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 3
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 65
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 2
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 5
194 Temperature_Celsius 0x0022 123 111 000 Old_age Always - 29
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 32 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 32 occurred at disk power-on lifetime: 60 hours (2 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 02 0c 6e 04 4a Error: IDNF at LBA = 0x0a046e0c = 168062476
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 02 0c 6e 04 4a 08 2d+12:57:50.535 WRITE DMA
ca 00 02 0c 6e 04 4a 08 2d+12:57:43.470 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:36.405 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:29.340 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:22.275 WRITE DMA
Error 31 occurred at disk power-on lifetime: 60 hours (2 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 02 0c 6e 04 4a Error: IDNF at LBA = 0x0a046e0c = 168062476
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 02 0c 6e 04 4a 08 2d+12:57:43.470 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:36.405 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:29.340 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:22.275 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:15.210 WRITE DMA
Error 30 occurred at disk power-on lifetime: 60 hours (2 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 02 0a 6e 04 4a Error: IDNF at LBA = 0x0a046e0a = 168062474
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 02 0a 6e 04 4a 08 2d+12:57:36.405 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:29.340 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:22.275 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:15.210 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:08.145 WRITE DMA
Error 29 occurred at disk power-on lifetime: 60 hours (2 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 02 0a 6e 04 4a Error: IDNF at LBA = 0x0a046e0a = 168062474
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 02 0a 6e 04 4a 08 2d+12:57:29.340 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:22.275 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:15.210 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:08.145 WRITE DMA
ca 00 02 08 6e 04 4a 08 2d+12:57:01.080 WRITE DMA
Error 28 occurred at disk power-on lifetime: 60 hours (2 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 02 0a 6e 04 4a Error: IDNF at LBA = 0x0a046e0a = 168062474
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 02 0a 6e 04 4a 08 2d+12:57:22.275 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:15.210 WRITE DMA
ca 00 02 0a 6e 04 4a 08 2d+12:57:08.145 WRITE DMA
ca 00 02 08 6e 04 4a 08 2d+12:57:01.080 WRITE DMA
ca 00 02 08 6e 04 4a 08 2d+12:56:54.015 WRITE DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 10 -
# 2 Conveyance offline Completed without error 00% 0 -
# 3 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.