I'm pretty sure it is, but why is a brand new disk dying after a month of use?
Code:
=== START OF INFORMATION SECTION === Model Family: Seagate IronWolf Device Model: ST4000VN008-2DR166 Serial Number: ZDH466SW LU WWN Device Id: 5 000c50 0b1639b23 Firmware Version: SC60 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5980 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Dec 4 16:54:45 2018 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 591) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 628) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x50bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 081 044 044 Pre-fail Always In_the_past 140027536 3 Spin_Up_Time 0x0003 093 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 21 5 Reallocated_Sector_Ct 0x0033 001 001 010 Pre-fail Always FAILING_NOW 632 7 Seek_Error_Rate 0x000f 087 060 045 Pre-fail Always - 478204775 9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 962 (167 15 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 21 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 3768 188 Command_Timeout 0x0032 100 098 000 Old_age Always - 4295032837 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 072 071 040 Old_age Always - 28 (Min/Max 23/29) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 3 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 50 194 Temperature_Celsius 0x0022 028 040 000 Old_age Always - 28 (0 19 0 0 0) 197 Current_Pending_Sector 0x0012 001 001 000 Old_age Always - 12144 198 Offline_Uncorrectable 0x0010 001 001 000 Old_age Offline - 12144 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 959 (104 178 0) 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 3959572807 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 1570783817 SMART Error Log Version: 1 ATA Error Count: 3763 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3763 occurred at disk power-on lifetime: 902 hours (37 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 37d+09:51:22.624 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:22.624 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:22.624 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:22.623 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:22.623 READ FPDMA QUEUED Error 3762 occurred at disk power-on lifetime: 902 hours (37 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 37d+09:51:19.411 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:19.411 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:19.411 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:19.411 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:19.411 READ FPDMA QUEUED Error 3761 occurred at disk power-on lifetime: 902 hours (37 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 37d+09:51:16.091 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:16.091 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:16.091 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:16.091 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:16.091 READ FPDMA QUEUED Error 3760 occurred at disk power-on lifetime: 902 hours (37 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 37d+09:51:12.768 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:12.768 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:12.768 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:12.768 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:12.768 READ FPDMA QUEUED Error 3759 occurred at disk power-on lifetime: 902 hours (37 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 37d+09:51:09.371 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:09.371 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:09.371 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:09.371 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 37d+09:51:09.371 READ FPDMA QUEUED SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
Last edited by a moderator: