- Joined
- Nov 25, 2013
- Messages
- 7,776
Hi, all,
after the disaster with the DOA WD drives I successfully replaced all disks of our small NAS.
Reference: https://forums.freenas.org/index.php?threads/wd-red-drives-not-spinning-up.25111/
Now, just one day later, I notice this - could someone please help me interpret the output? Should I suspect the connector in the enclosure or the controller?
APM set to 254 for all drives.
Thanks,
Patrick
after the disaster with the DOA WD drives I successfully replaced all disks of our small NAS.
Reference: https://forums.freenas.org/index.php?threads/wd-red-drives-not-spinning-up.25111/
Now, just one day later, I notice this - could someone please help me interpret the output? Should I suspect the connector in the enclosure or the controller?
APM set to 254 for all drives.
Thanks,
Patrick
Code:
(ada2:ahcich2:0:0:0): READ_FPDMA_QUEUED. ACB: 60 08 50 c1 82 40 ba 00 00 00 00 00 (ada2:ahcich2:0:0:0): CAM status: ATA Status Error (ada2:ahcich2:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC ) (ada2:ahcich2:0:0:0): RES: 41 40 50 c1 82 00 ba 00 00 08 00 (ada2:ahcich2:0:0:0): Retrying command (ada2:ahcich2:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 40 5c 99 40 d8 00 00 00 00 00 (ada2:ahcich2:0:0:0): CAM status: ATA Status Error (ada2:ahcich2:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC ) (ada2:ahcich2:0:0:0): RES: 41 40 40 5c 99 00 d8 00 00 10 00 (ada2:ahcich2:0:0:0): Retrying command ... da2:ahcich2:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 40 5c 99 40 d8 00 00 00 00 00 (ada2:ahcich2:0:0:0): CAM status: ATA Status Error (ada2:ahcich2:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC ) (ada2:ahcich2:0:0:0): RES: 41 40 48 5c 99 00 d8 00 00 10 00 (ada2:ahcich2:0:0:0): Error 5, Retries exhausted ... ahcich2: Timeout on slot 29 port 0 ahcich2: is 00000000 cs 20000000 ss 00000000 rs 20000000 tfd c0 serr 00000000 cmd 0000fd17 ahcich2: Error while READ LOG EXT (ada2:ahcich2:0:0:0): READ_FPDMA_QUEUED. ACB: 60 08 20 91 99 40 d8 00 00 00 00 00 (ada2:ahcich2:0:0:0): CAM status: ATA Status Error (ada2:ahcich2:0:0:0): ATA status: 00 () (ada2:ahcich2:0:0:0): RES: 00 00 00 00 00 00 00 00 00 00 00 (ada2:ahcich2:0:0:0): Retrying command (ada2:ahcich2:0:0:0): READ_FPDMA_QUEUED. ACB: 60 08 20 91 99 40 d8 00 00 00 00 00 (ada2:ahcich2:0:0:0): CAM status: ATA Status Error (ada2:ahcich2:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC ) (ada2:ahcich2:0:0:0): RES: 41 40 20 91 99 00 d8 00 00 08 00 (ada2:ahcich2:0:0:0): Retrying command ... (ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 50 a5 99 40 d8 00 00 00 08 00 (ada2:ahcich2:0:0:0): CAM status: ATA Status Error (ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC ) (ada2:ahcich2:0:0:0): RES: 51 40 50 a5 99 00 d8 00 00 00 00 (ada2:ahcich2:0:0:0): Error 5, Retries exhausted (ada2:ahcich2:0:0:0): READ_FPDMA_QUEUED. ACB: 60 08 20 c8 99 40 d8 00 00 00 00 00 (ada2:ahcich2:0:0:0): CAM status: ATA Status Error (ada2:ahcich2:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC ) (ada2:ahcich2:0:0:0): RES: 41 40 20 c8 99 00 d8 00 00 08 00 (ada2:ahcich2:0:0:0): Retrying command ... (ada2:ahcich2:0:0:0): READ_FPDMA_QUEUED. ACB: 60 08 20 c8 99 40 d8 00 00 00 00 00 (ada2:ahcich2:0:0:0): CAM status: ATA Status Error (ada2:ahcich2:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC ) (ada2:ahcich2:0:0:0): RES: 41 40 20 c8 99 00 d8 00 00 08 00 (ada2:ahcich2:0:0:0): Error 5, Retries exhausted ...
Code:
[root@freenas-je] ~# zpool status pool: zfs state: ONLINE scan: scrub in progress since Mon Dec 8 09:02:31 2014 790G scanned out of 4.99T at 309M/s, 3h58m to go 152K repaired, 15.45% done config: NAME STATE READ WRITE CKSUM zfs ONLINE 0 0 0 raidz2-0 ONLINE 0 0 0 ada0p2 ONLINE 0 0 0 ada1p2 ONLINE 0 0 0 ada2p2 ONLINE 0 0 0 (repairing) ada3p2 ONLINE 0 0 0 errors: No known data errors
Code:
[root@freenas-je] ~# smartctl -a /dev/ada2 smartctl 6.2 2013-07-26 r3841 [FreeBSD 9.2-RELEASE-p12 amd64] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ST4000VN000-1H4168 Serial Number: Z302C6XN LU WWN Device Id: 5 000c50 079481ce9 Firmware Version: SC44 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5900 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Dec 8 09:50:37 2014 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 107) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 531) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x10bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 115 092 006 Pre-fail Always - 90091760 3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 4 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 065 060 030 Pre-fail Always - 3616389 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 89 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 4 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 139 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 1 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 066 065 045 Old_age Always - 34 (Min/Max 31/34) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 0 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 4 194 Temperature_Celsius 0x0022 034 040 000 Old_age Always - 34 (0 19 0 0 0) 197 Current_Pending_Sector 0x0012 100 099 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 099 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 139 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 139 occurred at disk power-on lifetime: 88 hours (3 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 ff ff ff 4f 00 02:58:13.087 READ FPDMA QUEUED 60 00 38 ff ff ff 4f 00 02:58:13.086 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 02:58:13.064 READ LOG EXT 60 00 08 ff ff ff 4f 00 02:58:09.128 READ FPDMA QUEUED 60 00 38 ff ff ff 4f 00 02:58:09.127 READ FPDMA QUEUED Error 138 occurred at disk power-on lifetime: 88 hours (3 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 ff ff ff 4f 00 02:58:09.128 READ FPDMA QUEUED 60 00 38 ff ff ff 4f 00 02:58:09.127 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 02:58:09.093 READ LOG EXT 60 00 08 ff ff ff 4f 00 02:58:05.167 READ FPDMA QUEUED 60 00 38 ff ff ff 4f 00 02:58:05.166 READ FPDMA QUEUED Error 137 occurred at disk power-on lifetime: 88 hours (3 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 ff ff ff 4f 00 02:58:05.167 READ FPDMA QUEUED 60 00 38 ff ff ff 4f 00 02:58:05.166 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 02:58:05.133 READ LOG EXT 61 00 28 ff ff ff 4f 00 02:58:01.212 WRITE FPDMA QUEUED 60 00 08 ff ff ff 4f 00 02:58:01.212 READ FPDMA QUEUED Error 136 occurred at disk power-on lifetime: 88 hours (3 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: WP at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 00 28 ff ff ff 4f 00 02:58:01.212 WRITE FPDMA QUEUED 60 00 08 ff ff ff 4f 00 02:58:01.212 READ FPDMA QUEUED 60 00 38 ff ff ff 4f 00 02:58:01.211 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 02:58:01.134 READ LOG EXT 60 00 08 ff ff ff 4f 00 02:57:55.804 READ FPDMA QUEUED Error 135 occurred at disk power-on lifetime: 88 hours (3 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 ff ff ff 4f 00 02:57:55.804 READ FPDMA QUEUED 60 00 38 ff ff ff 4f 00 02:57:55.796 READ FPDMA QUEUED 60 00 10 ff ff ff 4f 00 02:57:55.794 READ FPDMA QUEUED 60 00 08 ff ff ff 4f 00 02:57:55.785 READ FPDMA QUEUED 60 00 18 ff ff ff 4f 00 02:57:55.782 READ FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 41 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.