Came back this morning after a good 10 hours, has only resilvered 13GB, showing 0.86%, 1064h remaning. Have run the smartctl -a /dev/ada3 and results are below.
[root@freenas] ~# smartctl -a /dev/ada3
smartctl 5.41 2011-06-09 r3365 [FreeBSD 8.2-RELEASE-p3 amd64] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: WDC WD20EARX-00PASB0
Serial Number: WD-WCAZA9318778
LU WWN Device Id: 5 0014ee 206316088
Firmware Version: 51.0AB51
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Dec 20 07:43:21 2011 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (37500) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 152 152 051 Pre-fail Always - 71451
3 Spin_Up_Time 0x0027 186 172 021 Pre-fail Always - 5683
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 60
5 Reallocated_Sector_Ct 0x0033 169 169 140 Pre-fail Always - 592
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1699
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 58
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 43
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 1629
194 Temperature_Celsius 0x0022 119 113 000 Old_age Always - 31
196 Reallocated_Event_Count 0x0032 150 150 000 Old_age Always - 50
197 Current_Pending_Sector 0x0032 001 001 000 Old_age Always - 65022
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 50
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 59
SMART Error Log Version: 1
ATA Error Count: 14674 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 14674 occurred at disk power-on lifetime: 1655 hours (68 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 80 fe 3f 40 Error: UNC at LBA = 0x003ffe80 = 4193920
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 80 fe 3f 40 08 00:14:48.195 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:44.515 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:40.055 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:37.345 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:34.650 READ DMA
Error 14673 occurred at disk power-on lifetime: 1655 hours (68 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 80 fe 3f 40 Error: UNC at LBA = 0x003ffe80 = 4193920
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 80 fe 3f 40 08 00:14:44.515 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:40.055 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:37.345 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:34.650 READ DMA
Error 14672 occurred at disk power-on lifetime: 1655 hours (68 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 80 fe 3f 40 Error: UNC at LBA = 0x003ffe80 = 4193920
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 80 fe 3f 40 08 00:14:40.055 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:37.345 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:34.650 READ DMA
Error 14671 occurred at disk power-on lifetime: 1655 hours (68 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 80 fe 3f 40 Error: UNC at LBA = 0x003ffe80 = 4193920
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 80 fe 3f 40 08 00:14:37.345 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:34.650 READ DMA
Error 14670 occurred at disk power-on lifetime: 1655 hours (68 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 80 fe 3f 40 Error: UNC at LBA = 0x003ffe80 = 4193920
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 80 fe 3f 40 08 00:14:34.650 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
EDIT:
I have also ran the command across the other 4 drives in the server and none of them are showing any errors like this drive...
[root@freenas] ~# smartctl -a /dev/ada3
smartctl 5.41 2011-06-09 r3365 [FreeBSD 8.2-RELEASE-p3 amd64] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: WDC WD20EARX-00PASB0
Serial Number: WD-WCAZA9318778
LU WWN Device Id: 5 0014ee 206316088
Firmware Version: 51.0AB51
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Dec 20 07:43:21 2011 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (37500) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 152 152 051 Pre-fail Always - 71451
3 Spin_Up_Time 0x0027 186 172 021 Pre-fail Always - 5683
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 60
5 Reallocated_Sector_Ct 0x0033 169 169 140 Pre-fail Always - 592
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1699
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 58
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 43
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 1629
194 Temperature_Celsius 0x0022 119 113 000 Old_age Always - 31
196 Reallocated_Event_Count 0x0032 150 150 000 Old_age Always - 50
197 Current_Pending_Sector 0x0032 001 001 000 Old_age Always - 65022
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 50
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 59
SMART Error Log Version: 1
ATA Error Count: 14674 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 14674 occurred at disk power-on lifetime: 1655 hours (68 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 80 fe 3f 40 Error: UNC at LBA = 0x003ffe80 = 4193920
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 80 fe 3f 40 08 00:14:48.195 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:44.515 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:40.055 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:37.345 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:34.650 READ DMA
Error 14673 occurred at disk power-on lifetime: 1655 hours (68 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 80 fe 3f 40 Error: UNC at LBA = 0x003ffe80 = 4193920
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 80 fe 3f 40 08 00:14:44.515 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:40.055 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:37.345 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:34.650 READ DMA
Error 14672 occurred at disk power-on lifetime: 1655 hours (68 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 80 fe 3f 40 Error: UNC at LBA = 0x003ffe80 = 4193920
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 80 fe 3f 40 08 00:14:40.055 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:37.345 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:34.650 READ DMA
Error 14671 occurred at disk power-on lifetime: 1655 hours (68 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 80 fe 3f 40 Error: UNC at LBA = 0x003ffe80 = 4193920
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 80 fe 3f 40 08 00:14:37.345 READ DMA
c8 00 00 80 fe 3f 40 08 00:14:34.650 READ DMA
Error 14670 occurred at disk power-on lifetime: 1655 hours (68 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 80 fe 3f 40 Error: UNC at LBA = 0x003ffe80 = 4193920
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 80 fe 3f 40 08 00:14:34.650 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
EDIT:
I have also ran the command across the other 4 drives in the server and none of them are showing any errors like this drive...
