Ethernet Card and 9.3.1 Update

[korrupto77]

Hi Gents,

Maybe someone of You has already encountered similar issue;

I have a Network Adapter with RTL8169SC chipset which works fine on 9.3, whe i try to upgrade system to 9.3.1, OS doesn't recognize ETH adapter ( no configured interfaces were found) no way to configure manually . I've verified and chipset is included in re4 BSD driver . Does anyone have any suggestion ??

Thanks In Advance

 

[dlavigne]

Paste the output of ifconfig using Insert -> Code.

 

[korrupto77]

re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether d0:50:99:44:d3:40
nd6 options=9<PERFORMNUD,IFDISABLED>
media: Ethernet autoselect (none)
status: no carrier
re1: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=82099<RXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether 00:30:4f:6a:24:ce
inet 172.16.10.37 netmask 0xffff0000 broadcast 172.16.255.255
nd6 options=9<PERFORMNUD,IFDISABLED>
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
ipfw0: flags=8801<UP,SIMPLEX,MULTICAST> metric 0 mtu 65536
nd6 options=9<PERFORMNUD,IFDISABLED>
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x6
inet 127.0.0.1 netmask 0xff000000
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
bridge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 02:5b:3f:ef:d1:00
nd6 options=1<PERFORMNUD>
id 00:00:00:00:00:00 priority 32768 hellotime 2 fwddelay 15
maxage 20 holdcnt 6 proto rstp maxaddr 2000 timeout 1200
root id 00:00:00:00:00:00 priority 32768 ifcost 0 port 0
member: epair0a flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 8 priority 128 path cost 2000
member: re1 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 4 priority 128 path cost 200000
epair0a: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8<VLAN_MTU>
ether 02:43:5d:00:08:0a
nd6 options=1<PERFORMNUD>
media: Ethernet 10Gbase-T (10Gbase-T <full-duplex>)
status: active

 

[dlavigne]

re1: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=82099<RXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether 00:30:4f:6a:24:ce
inet 172.16.10.37 netmask 0xffff0000 broadcast 172.16.255.255
nd6 options=9<PERFORMNUD,IFDISABLED>
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active

This interface is active and configured. Were you expecting something else?

 

[korrupto77]

Now is working fine, if im applying the 9.3.1 update it stops to work

im doing now in order to paste here the output of ifconfig

 

[korrupto77]

dlavigne , How do I post output from console setup ?? :(

 

[SweetAndLow]

Use ipmi or take photo.

 

[korrupto77]

here we are

 

[pirateghost]

Realtek is the problem

 

[korrupto77]

pirateghost u mean my nic is not compatible ??:(

 

[SweetAndLow]

Realtek is the problem

I agree but there should at least be an IP.


@korrupto77 that nic is terrible and will probably cause all kinds of problems for freenas.

 

[korrupto77]

no way i've tried to assign ip netmask i went into gui but so many errors, i'm gonna buy an intel chipset !!

 

[korrupto77]

I agree but there should at least be an IP.


@korrupto77 that nic is terrible and will probably cause all kinds of problems for freenas.

I've seen !!! till 9.3 is ok but with upgrade doesn't want to work !!

 

[korrupto77]

Thanks for the support guys,
any suggestion for acceptable eth card ( not too expensive ) ??

 

[pirateghost]

Thanks for the support guys,
any suggestion for acceptable eth card ( not too expensive ) ??

Intel

 

[Ericloewe]

Thanks for the support guys,
any suggestion for acceptable eth card ( not too expensive ) ??

http://www.amazon.de/Intel-EXPI9301...UTF8&qid=1452524591&sr=8-1&keywords=intel+nic

 

[korrupto77]

http://www.amazon.de/Intel-EXPI9301...UTF8&qid=1452524591&sr=8-1&keywords=intel+nic

WOW thanks !!

 

[jgreco]

A typical Intel PCIe desktop card for about thirty dollars will work wonders. Plus it'll actually work, unlike Realteks, which seem rather hit-or-miss.

 

[korrupto77]

Heeeelllllllppppp, I've changed the card with an intel EXPI9301CTBLK but is same , it doesn't change the !!! does someone can help me ?? any idea ??

Thanks Guys

 

[depasseg]

So on the working system, you are connected at 100M full duplex and after the upgrade, the speed is 10M half duplex. I'd look at cabling or the switch port that the freenas connects to.