nissnn
Cadet
- Joined
- Mar 14, 2019
- Messages
- 7
Hello Everybody,
Today I was cleaning my NAS Build and when powering it back on afterwards one drive was not showing up and this error was showing:
I shut down the system and checked all the cabling, when powering on again the drive showed up but I still get the same error.
Running zpool Status returns this:
The drive that was not showing up and is now unavailable seems to be fine:
Onlining it doesn't work I just get:
Is it possible that the drive is just not properly recognised because it was missing once and can I somehow reconnect it?
Thanks for reading,
nissnn
Today I was cleaning my NAS Build and when powering it back on afterwards one drive was not showing up and this error was showing:
Code:
The volume Speicherplatz state is DEGRADED: One or more devices could not be opened. Sufficient replicas exist for the pool to continue functioning in a degraded state.
I shut down the system and checked all the cabling, when powering on again the drive showed up but I still get the same error.
Running zpool Status returns this:
Code:
pool: Speicherplatz state: DEGRADED status: One or more devices could not be opened. Sufficient replicas exist for the pool to continue functioning in a degraded state. action: Attach the missing device and online it using 'zpool online'. see: http://illumos.org/msg/ZFS-8000-2Q scan: none requested config: NAME STATE READ WRITE CKSUM Speicherplatz DEGRADED 0 0 0 raidz1-0 DEGRADED 0 0 0 gptid/d3490947-4009-11e9-b436-bcaec5dcfcad.eli ONLINE 0 0 0 15070291121131822168 UNAVAIL 0 0 0 was /dev/gptid/d46c4f36-4009-11e9-b436-bcaec5dcfcad.eli gptid/d5b48372-4009-11e9-b436-bcaec5dcfcad.eli ONLINE 0 0 0 gptid/d6f078d8-4009-11e9-b436-bcaec5dcfcad.eli ONLINE 0 0 0 errors: No known data errors pool: freenas-boot state: ONLINE scan: scrub repaired 0 in 0 days 00:00:03 with 0 errors on Thu Mar 14 03:45:03 2019 config: NAME STATE READ WRITE CKSUM freenas-boot ONLINE 0 0 0 ada3p2 ONLINE 0 0 0 errors: No known data errors
The drive that was not showing up and is now unavailable seems to be fine:
Code:
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.2-STABLE amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Enterprise Capacity 3.5 HDD Device Model: ST10000NM0086-2AA101 Serial Number: ZA21ET7T LU WWN Device Id: 5 000c50 074424642 Firmware Version: SN05 User Capacity: 10,000,831,348,736 bytes [10.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Wed Mar 20 20:42:40 2019 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 567) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 950) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 080 064 044 Pre-fail Always - 108588180 3 Spin_Up_Time 0x0003 091 091 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 37 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 082 060 045 Pre-fail Always - 171839681 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 687 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 37 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0 189 High_Fly_Writes 0x003a 064 064 000 Old_age Always - 36 190 Airflow_Temperature_Cel 0x0022 065 053 040 Old_age Always - 35 (Min/Max 34/35) 191 G-Sense_Error_Rate 0x0032 098 098 000 Old_age Always - 5539 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 30 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 142 194 Temperature_Celsius 0x0022 035 047 000 Old_age Always - 35 (0 19 0 0 0) 195 Hardware_ECC_Recovered 0x001a 080 064 000 Old_age Always - 108588180 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0023 100 100 001 Pre-fail Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 683h+37m+44.452s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 110853972576 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 138308350991 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 684 - # 2 Extended offline Interrupted (host reset) 00% 655 - # 3 Extended offline Completed without error 00% 636 - # 4 Extended offline Aborted by host 20% 609 - # 5 Extended offline Completed without error 00% 589 - # 6 Extended offline Completed without error 00% 560 - # 7 Extended offline Interrupted (host reset) 60% 493 - # 8 Extended offline Interrupted (host reset) 80% 466 - # 9 Extended offline Interrupted (host reset) 90% 441 - #10 Extended offline Interrupted (host reset) 80% 422 - #11 Extended offline Completed without error 00% 16 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
Onlining it doesn't work I just get:
Code:
warning: device '15070291121131822168' onlined, but remains in faulted state
Is it possible that the drive is just not properly recognised because it was missing once and can I somehow reconnect it?
Thanks for reading,
nissnn