hardwarejunky009
Cadet
- Joined
- Dec 22, 2018
- Messages
- 4
Hello,
HW:
KALEA-INFORMATIQUE PCI Express Karte - 4X SATA 6Gb/s, mit miniSAS Kabel. PCIe 2.0. Marvell 88SE9215
and SilverStone SST-FS304B
5 drives in ZFS2 - array (all 6TB drives)
3xST6000VX001-2BD186
1xWDC WD6002FRYZ-01WD5B1
1xWDC WD60EFZX-68B3FN0
I weekly check the status of my Nas and became an array status degraded:
One seagate ST6000VX001-2BD186 has some ATA Error Count: 167 increast:
I then started a extended offline Selftest, but am not sure is the drive failing or the SAS cabel faulty? I never had any problems with SAS cabels so im not sure how I would approach this kind of error. Should I order new SAS cabel and see if the ATA error count is stabel or should I run more smart test on the drive?
best regards
hardwarejunky
HW:
KALEA-INFORMATIQUE PCI Express Karte - 4X SATA 6Gb/s, mit miniSAS Kabel. PCIe 2.0. Marvell 88SE9215
and SilverStone SST-FS304B
5 drives in ZFS2 - array (all 6TB drives)
3xST6000VX001-2BD186
1xWDC WD6002FRYZ-01WD5B1
1xWDC WD60EFZX-68B3FN0
I weekly check the status of my Nas and became an array status degraded:
One seagate ST6000VX001-2BD186 has some ATA Error Count: 167 increast:
Code:
root@freenas[~]# smartctl -a /dev/ada8 smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p9 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Skyhawk Device Model: ST6000VX001-2BD186 Serial Number: XXXXXXXXXXXXXX LU WWN Device Id: 5 000c50 0dbaa881f Firmware Version: CV12 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5425 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Oct 3 17:09:22 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 249) Self-test routine in progress... 90% of test remaining. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 724) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 076 064 006 Pre-fail Always - 35548372 3 Spin_Up_Time 0x0003 091 091 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 107 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 070 060 045 Pre-fail Always - 9856939 9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1779h+00m+00.000s 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 3 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 167 188 Command_Timeout 0x0032 098 098 000 Old_age Always - 4295032834 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 069 067 040 Old_age Always - 31 (Min/Max 23/33) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 2 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 530 194 Temperature_Celsius 0x0022 031 040 000 Old_age Always - 31 (0 23 0 0 0) 195 Hardware_ECC_Recovered 0x001a 076 064 000 Old_age Always - 35548372 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 1 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 746h+54m+56.288s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 11714087042 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 7192183930 SMART Error Log Version: 1 ATA Error Count: 167 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 167 occurred at disk power-on lifetime: 1759 hours (73 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 b0 ff ff ff 4f 00 23d+14:02:57.719 READ DMA EXT 61 00 00 ff ff ff 4f 00 23d+14:02:57.717 WRITE FPDMA QUEUED b0 d5 01 09 4f c2 40 00 23d+14:02:57.689 SMART READ LOG 25 00 00 ff ff ff 4f 00 23d+14:02:54.022 READ DMA EXT b0 d5 01 06 4f c2 40 00 23d+14:02:53.886 SMART READ LOG Error 166 occurred at disk power-on lifetime: 1759 hours (73 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff 4f 00 23d+14:02:54.022 READ DMA EXT b0 d5 01 06 4f c2 40 00 23d+14:02:53.886 SMART READ LOG 25 00 00 ff ff ff 4f 00 23d+14:02:50.223 READ DMA EXT b0 d5 01 01 4f c2 40 00 23d+14:02:50.183 SMART READ LOG 25 00 00 ff ff ff 4f 00 23d+14:02:46.515 READ DMA EXT Error 165 occurred at disk power-on lifetime: 1759 hours (73 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff 4f 00 23d+14:02:50.223 READ DMA EXT b0 d5 01 01 4f c2 40 00 23d+14:02:50.183 SMART READ LOG 25 00 00 ff ff ff 4f 00 23d+14:02:46.515 READ DMA EXT b0 d5 01 00 4f c2 40 00 23d+14:02:46.513 SMART READ LOG 25 00 00 ff ff ff 4f 00 23d+14:02:42.801 READ DMA EXT Error 164 occurred at disk power-on lifetime: 1759 hours (73 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff 4f 00 23d+14:02:46.515 READ DMA EXT b0 d5 01 00 4f c2 40 00 23d+14:02:46.513 SMART READ LOG 25 00 00 ff ff ff 4f 00 23d+14:02:42.801 READ DMA EXT b0 da 00 00 4f c2 40 00 23d+14:02:42.494 SMART RETURN STATUS 25 00 00 ff ff ff 4f 00 23d+14:02:38.202 READ DMA EXT Error 163 occurred at disk power-on lifetime: 1759 hours (73 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff 4f 00 23d+14:02:42.801 READ DMA EXT b0 da 00 00 4f c2 40 00 23d+14:02:42.494 SMART RETURN STATUS 25 00 00 ff ff ff 4f 00 23d+14:02:38.202 READ DMA EXT b0 d1 01 01 4f c2 40 00 23d+14:02:38.188 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] 2f 00 01 10 00 00 00 00 23d+14:02:38.188 READ LOG EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Self-test routine in progress 90% 1779 - # 2 Short offline Completed without error 00% 1762 - # 3 Short offline Completed without error 00% 1594 - # 4 Short offline Completed without error 00% 1426 - # 5 Short offline Completed without error 00% 1258 - # 6 Short offline Completed without error 00% 1098 - # 7 Short offline Completed without error 00% 922 - # 8 Short offline Completed without error 00% 754 - # 9 Short offline Completed without error 00% 586 - #10 Short offline Completed without error 00% 418 - #11 Short offline Completed without error 00% 250 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. root@freenas[~]# smartctl -l selftest /dev/ada8 smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p9 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Self-test routine in progress 90% 1779 - # 2 Short offline Completed without error 00% 1762 - # 3 Short offline Completed without error 00% 1594 - # 4 Short offline Completed without error 00% 1426 - # 5 Short offline Completed without error 00% 1258 - # 6 Short offline Completed without error 00% 1098 - # 7 Short offline Completed without error 00% 922 - # 8 Short offline Completed without error 00% 754 - # 9 Short offline Completed without error 00% 586 - #10 Short offline Completed without error 00% 418 - #11 Short offline Completed without error 00% 250 -
I then started a extended offline Selftest, but am not sure is the drive failing or the SAS cabel faulty? I never had any problems with SAS cabels so im not sure how I would approach this kind of error. Should I order new SAS cabel and see if the ATA error count is stabel or should I run more smart test on the drive?
best regards
hardwarejunky