So I want to clarify the SSD is only missing on certain screens in the UI. Here's what I'm seeing:
Note that sdd is missing and that there is only one drive showing up for my boot-pool. sdd is also missing from the Data Protection pages and Reporting pages. The API doesn't show anything for it either.
If I go to the boot pool status page, I still see sdd showing up as part of the mirror.
It shows up on the command line:
I can get the smartctl results for the drive as well.
I've tried rebooting numerous times, no joy. Anyone have any ideas how to fix this issue?
Note that sdd is missing and that there is only one drive showing up for my boot-pool. sdd is also missing from the Data Protection pages and Reporting pages. The API doesn't show anything for it either.
If I go to the boot pool status page, I still see sdd showing up as part of the mirror.
It shows up on the command line:
I can get the smartctl results for the drive as well.
Code:
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.79+truenas] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Samsung SSD 870 EVO 1TB Serial Number: ***** LU WWN Device Id: 5 002538 f424276f4 Firmware Version: SVT02B6Q User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Apr 21 11:16:38 2023 AEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART Status command failed: scsi error unsupported scsi opcode SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 4027 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 19 177 Wear_Leveling_Count 0x0013 099 099 000 Pre-fail Always - 12 179 Used_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 0 181 Program_Fail_Cnt_Total 0x0032 100 100 010 Old_age Always - 0 182 Erase_Fail_Count_Total 0x0032 100 100 010 Old_age Always - 0 183 Runtime_Bad_Block 0x0013 100 100 010 Pre-fail Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0032 069 048 000 Old_age Always - 31 195 Hardware_ECC_Recovered 0x001a 200 200 000 Old_age Always - 0 199 UDMA_CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0 235 Unknown_Attribute 0x0012 099 099 000 Old_age Always - 7 241 Total_LBAs_Written 0x0032 099 099 000 Old_age Always - 17711771145 252 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 1 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 3922 - # 2 Short offline Completed without error 00% 3754 - # 3 Short offline Completed without error 00% 3587 - # 4 Extended offline Completed without error 00% 3538 - # 5 Short offline Completed without error 00% 3417 - # 6 Short offline Completed without error 00% 3250 - # 7 Short offline Completed without error 00% 3082 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 256 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
I've tried rebooting numerous times, no joy. Anyone have any ideas how to fix this issue?