MartinCorby
Dabbler
- Joined
- Sep 5, 2015
- Messages
- 10
Setting up FreeNAS for the first time on an older machine.
Installation has gone swimmingly - booted from CD onto USB Flash drive all OK.
System is set up with x2 1TB HDD :
I have double checked to make sure FreeNAS is loaded onto the USB Flash drive and boots from there (I disconnected the HDD's during installation)
I'm looking for a steer as to how I can get FreeNAS to recognise the second (Seagate) HDD
Output from dmesg :
da0: 3864MB (7913472 512 byte sectors: 255H 63S/T 492C)
da0: quirks=0x3<NO_SYNC_CACHE,NO_6_BYTE>
SATA 3.x device
ada0: Serial Number Z4Y4NY6X
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
ada0: quirks=0x1<4K>
ada0: Previously was known as ad10
ada1 at ahcich3 bus 0 scbus4 target 0 lun 0
ada1: <WDC WD10EADS-00M2B0 01.00A01> ATA-8 SATA 2.x device
ada1: Serial Number WD-WCAV5J490135
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
ada1: Previously was known as ad12
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 1200986158 Hz quality 1000
Trying to mount root from zfs:freenas-boot/ROOT/default []...
GEOM_RAID5: Module loaded, version 1.3.20140711.62 (rev f91e28e40bf7)
wbwd0: DevID 0xa0 DevRev 0x23, will not attach, please report this.
vboxdrv: fAsync=0 offMin=0x3f0 offMax=0x84c
pid 1514 (syslog-ng), uid 0: exited on signal 6 (core dumped)
[root@freenas ~]#
Attached is the Debug dowmload
Hope all that helps
Installation has gone swimmingly - booted from CD onto USB Flash drive all OK.
System is set up with x2 1TB HDD :
- WESTERN DIGITAL Green WD10EADS 1TB SATA II 32MB
- Seagate 1TB 3.5" SATA Desktop Hard Drive
I have double checked to make sure FreeNAS is loaded onto the USB Flash drive and boots from there (I disconnected the HDD's during installation)
I'm looking for a steer as to how I can get FreeNAS to recognise the second (Seagate) HDD
Output from dmesg :
da0: 3864MB (7913472 512 byte sectors: 255H 63S/T 492C)
da0: quirks=0x3<NO_SYNC_CACHE,NO_6_BYTE>
SATA 3.x device
ada0: Serial Number Z4Y4NY6X
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
ada0: quirks=0x1<4K>
ada0: Previously was known as ad10
ada1 at ahcich3 bus 0 scbus4 target 0 lun 0
ada1: <WDC WD10EADS-00M2B0 01.00A01> ATA-8 SATA 2.x device
ada1: Serial Number WD-WCAV5J490135
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
ada1: Previously was known as ad12
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 1200986158 Hz quality 1000
Trying to mount root from zfs:freenas-boot/ROOT/default []...
GEOM_RAID5: Module loaded, version 1.3.20140711.62 (rev f91e28e40bf7)
wbwd0: DevID 0xa0 DevRev 0x23, will not attach, please report this.
vboxdrv: fAsync=0 offMin=0x3f0 offMax=0x84c
pid 1514 (syslog-ng), uid 0: exited on signal 6 (core dumped)
[root@freenas ~]#
Attached is the Debug dowmload
Hope all that helps