I have 12 WD Gold 12TBs in a Lenovo SA120 DAS enclosure. As soon as I created the volume and mounted it I started seeing these errors on all the disks. I can't seem to figure out what's causing the errors. Any ideas what could be the cause?
Code:
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.1-STABLE amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD121KRYZ-01W0RB0 Serial Number: 8DJYV3JY LU WWN Device Id: 5 000cca 253e9bfcc Firmware Version: 01.01H01 User Capacity: 12,000,138,625,024 bytes [12.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Feb 12 17:17:43 2019 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 87) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: (1256) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 132 132 054 Pre-fail Offline - 96 3 Spin_Up_Time 0x0007 100 100 024 Pre-fail Always - 0 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 1 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 128 128 020 Pre-fail Offline - 18 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 618 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1 22 Unknown_Attribute 0x0023 100 100 025 Pre-fail Always - 100 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 27 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 27 194 Temperature_Celsius 0x0002 214 214 000 Old_age Always - 28 (Min/Max 20/32) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 199 199 000 Old_age Always - 91 SMART Error Log Version: 1 ATA Error Count: 91 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 91 occurred at disk power-on lifetime: 618 hours (25 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 18 00 90 20 69 40 00 25d+18:16:49.740 READ FPDMA QUEUED 60 18 00 58 20 69 40 00 25d+18:16:49.740 READ FPDMA QUEUED 60 18 00 40 20 69 40 00 25d+18:16:49.740 READ FPDMA QUEUED 60 18 00 20 20 69 40 00 25d+18:16:49.739 READ FPDMA QUEUED 60 50 00 d0 1f 69 40 00 25d+18:16:48.884 READ FPDMA QUEUED Error 90 occurred at disk power-on lifetime: 618 hours (25 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 18 00 60 8a 1b 40 00 25d+18:15:10.085 READ FPDMA QUEUED 60 18 00 28 8a 1b 40 00 25d+18:15:10.083 READ FPDMA QUEUED 60 18 00 b8 89 1b 40 00 25d+18:15:10.082 READ FPDMA QUEUED 60 18 00 80 89 1b 40 00 25d+18:15:10.081 READ FPDMA QUEUED 60 18 00 48 89 1b 40 00 25d+18:15:10.080 READ FPDMA QUEUED Error 89 occurred at disk power-on lifetime: 618 hours (25 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 18 00 08 84 1b 40 00 25d+18:15:09.293 READ FPDMA QUEUED 60 18 00 d0 83 1b 40 00 25d+18:15:09.292 READ FPDMA QUEUED 60 18 00 28 83 1b 40 00 25d+18:15:09.292 READ FPDMA QUEUED 60 18 00 98 83 1b 40 00 25d+18:15:09.292 READ FPDMA QUEUED 60 18 00 f0 82 1b 40 00 25d+18:15:09.077 READ FPDMA QUEUED Error 88 occurred at disk power-on lifetime: 618 hours (25 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 20 00 a8 7d 1b 40 00 25d+18:15:08.464 READ FPDMA QUEUED 60 20 00 70 7d 1b 40 00 25d+18:15:08.307 READ FPDMA QUEUED 60 48 18 60 7d 1b 40 00 25d+18:15:08.306 READ FPDMA QUEUED 60 00 10 60 7c 1b 40 00 25d+18:15:08.306 READ FPDMA QUEUED 60 00 08 60 7b 1b 40 00 25d+18:15:08.306 READ FPDMA QUEUED Error 87 occurred at disk power-on lifetime: 618 hours (25 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 18 58 6d a7 40 00 25d+18:14:41.512 READ FPDMA QUEUED 60 a0 00 f0 6f a7 40 00 25d+18:14:41.510 READ FPDMA QUEUED 60 18 30 d0 6f a7 40 00 25d+18:14:41.490 READ FPDMA QUEUED 60 78 28 58 6f a7 40 00 25d+18:14:41.490 READ FPDMA QUEUED 60 00 20 58 6e a7 40 00 25d+18:14:41.490 READ FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 604 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.