New Internal SATA drive not recognized in freenas

[StoneyBalony]

I have purchased a new Toshiba 2TB Sata drive. When booting to freenas, the drive it not able to be seen.

The drive is shown in the BIOS and works properly when booting to Windows.

I have searched google and these forums, and to be honest, most of what I see, I do not understand as I am just starting to use freeNAS.

I used the same machine in the past, and was able to see and use IDE drives just fine. Any help will be greatly appreciated.

Thank you,
Stoney

 

[StoneyBalony]

* Hardware:

1. * Motherboard (Model)
2. *CPU - Intel Pentium 4 CPU 3GHz
3. * RAM - 4GB 533MHz DDR2 SDRAM
4. * HD - currently 1x 2TB Toshiba 7200 RPM 64MB cache

 

[StoneyBalony]

Code:

ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
lapic1: Forcing LINT1 to edge trigger
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 1496281627 Hz quality 1000
Root mount waiting for: usbus4 usbus3 usbus2 usbus1 usbus0
uhub2: 2 ports with 2 removable, self powered
uhub0: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
Root mount waiting for: usbus4
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
Root mount waiting for: usbus4
ugen4.2: <SanDisk> at usbus4
umass0: <SanDisk Cruzer Glide, class 0/0, rev 2.00/1.27, addr 2> on usbus4
umass0: SCSI over Bulk-Only; quirks = 0x0100
umass0:4:0:-1: Attached to scbus4
da0 at umass-sim0 bus 0 scbus4 target 0 lun 0
da0: <SanDisk Cruzer Glide 1.27> Removable Direct Access SCSI-6 device
da0: Serial Number 4C530000250411101030
da0: 40.000MB/s transfers
da0: 7633MB (15633408 512 byte sectors: 255H 63S/T 973C)
da0: quirks=0x2<NO_6_BYTE>
Root mount waiting for: usbus4
Trying to mount root from ufs:/dev/ufs/FreeNASs1a [ro]...
ugen3.2: <Logitech> at usbus3
ukbd0: <Logitech USB Receiver, class 0/0, rev 2.00/23.00, addr 2> on usbus3
kbd2 at ukbd0
ums0: <Logitech USB Receiver, class 0/0, rev 2.00/23.00, addr 2> on usbus3
ums0: 18 buttons and [XYZT] coordinates ID=2
GEOM_RAID5: Module loaded, version 1.1.20130907.44 (rev 5c6d2a159411)
ZFS NOTICE: Prefetch is disabled by default on i386 -- to enable,
add "vfs.zfs.prefetch_disable=0" to /boot/loader.conf.
ZFS WARNING: Recommended minimum kmem_size is 512MB; expect unstable behavior.
Consider tuning vm.kmem_size and vm.kmem_size_max
in /boot/loader.conf.
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
vboxdrv: fAsync=0 offMin=0x70f offMax=0x1a8b

 

[Ericloewe]

Your hardware is inadequate. Dangerously so. Please read the stickies regarding hardware recommendations.

Putting that aside, without telling us what motherboard/SATA controller you're using, there's not much we can say.