Code:
[root@freenas] ~# smartctl -a /dev/da1
smartctl 6.1 2013-03-16 r3800 [FreeBSD 9.1-STABLE amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K2000
Device Model: Hitachi HDS722020ALA330
Serial Number: JK1130YAGLAX5T
LU WWN Device Id: 5 000cca 221c857a1
Firmware Version: JKAOA20N
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Aug 29 18:20:56 2013 MST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART STATUS RETURN: incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (22036) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 367) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 086 086 016 Pre-fail Always - 154
2 Throughput_Performance 0x0005 133 133 054 Pre-fail Offline - 101
3 Spin_Up_Time 0x0007 156 156 024 Pre-fail Always - 505 (Average 422)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 158
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 3
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 112 112 020 Pre-fail Offline - 39
9 Power_On_Hours 0x0012 096 096 000 Old_age Always - 32952
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 145
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1001
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 1001
194 Temperature_Celsius 0x0002 146 146 000 Old_age Always - 41 (Min/Max 21/59)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 3
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 2
SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 occurred at disk power-on lifetime: 5217 hours (217 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 56 aa 33 4d 00 Error: ICRC, ABRT at LBA = 0x004d33aa = 5059498
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 98 00 33 4d 40 00 34d+10:46:03.585 WRITE FPDMA QUEUED
60 00 90 00 32 4d 40 00 34d+10:46:03.457 READ FPDMA QUEUED
60 00 88 00 31 4d 40 00 34d+10:46:03.447 READ FPDMA QUEUED
61 00 80 00 30 4d 40 00 34d+10:46:03.443 WRITE FPDMA QUEUED
60 00 78 00 2f 4d 40 00 34d+10:46:03.425 READ FPDMA QUEUED
Error 1 occurred at disk power-on lifetime: 2646 hours (110 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 2b 15 94 9b 00 Error: ICRC, ABRT 43 sectors at LBA = 0x009b9415 = 10195989
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
35 00 40 00 94 9b e3 00 26d+19:37:29.751 WRITE DMA EXT
35 00 40 c0 93 9b e3 00 26d+19:37:29.749 WRITE DMA EXT
35 00 40 80 93 9b e3 00 26d+19:37:29.747 WRITE DMA EXT
35 00 40 40 93 9b e3 00 26d+19:37:29.745 WRITE DMA EXT
35 00 40 00 93 9b e3 00 26d+19:37:29.743 WRITE DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 32946 -
# 2 Short offline Completed without error 00% 32934 -
# 3 Short offline Completed without error 00% 32922 -
# 4 Short offline Completed without error 00% 32910 -
# 5 Short offline Completed without error 00% 32898 -
# 6 Short offline Completed without error 00% 32886 -
# 7 Short offline Completed without error 00% 32874 -
# 8 Short offline Completed without error 00% 32862 -
# 9 Short offline Completed without error 00% 32850 -
#10 Short offline Completed without error 00% 32838 -
#11 Short offline Completed without error 00% 32826 -
#12 Short offline Completed without error 00% 32814 -
#13 Short offline Completed without error 00% 32802 -
#14 Short offline Completed without error 00% 32790 -
#15 Short offline Completed without error 00% 32778 -
#16 Short offline Completed without error 00% 32766 -
#17 Short offline Completed without error 00% 32754 -
#18 Short offline Completed without error 00% 32742 -
#19 Short offline Completed without error 00% 32730 -
#20 Short offline Completed without error 00% 32718 -
#21 Short offline Completed without error 00% 32706 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
[root@freenas] ~# smartctl -a /dev/da2
smartctl 6.1 2013-03-16 r3800 [FreeBSD 9.1-STABLE amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K2000
Device Model: Hitachi HDS722020ALA330
Serial Number: JK1130YAH4KWVT
LU WWN Device Id: 5 000cca 221d02c2d
Firmware Version: JKAOA28A
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Aug 29 18:22:18 2013 MST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART STATUS RETURN: incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (22918) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 382) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 093 093 016 Pre-fail Always - 131107
2 Throughput_Performance 0x0005 132 132 054 Pre-fail Offline - 103
3 Spin_Up_Time 0x0007 154 154 024 Pre-fail Always - 407 (Average 532)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 167
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 2
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 110 110 020 Pre-fail Offline - 40
9 Power_On_Hours 0x0012 096 096 000 Old_age Always - 30897
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 137
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1003
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 1003
194 Temperature_Celsius 0x0002 150 150 000 Old_age Always - 40 (Min/Max 21/60)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 2
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 0
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 30891 -
# 2 Short offline Completed without error 00% 30879 -
# 3 Short offline Completed without error 00% 30867 -
# 4 Short offline Completed without error 00% 30855 -
# 5 Short offline Completed without error 00% 30843 -
# 6 Short offline Completed without error 00% 30831 -
# 7 Short offline Completed without error 00% 30819 -
# 8 Short offline Completed without error 00% 30807 -
# 9 Short offline Completed without error 00% 30795 -
#10 Short offline Completed without error 00% 30783 -
#11 Short offline Completed without error 00% 30771 -
#12 Short offline Completed without error 00% 30759 -
#13 Short offline Completed without error 00% 30747 -
#14 Short offline Completed without error 00% 30735 -
#15 Short offline Completed without error 00% 30723 -
#16 Short offline Completed without error 00% 30711 -
#17 Short offline Completed without error 00% 30699 -
#18 Short offline Completed without error 00% 30687 -
#19 Short offline Completed without error 00% 30675 -
#20 Short offline Completed without error 00% 30663 -
#21 Short offline Completed without error 00% 30651 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
[root@freenas] ~# smartctl -a /dev/da3
smartctl 6.1 2013-03-16 r3800 [FreeBSD 9.1-STABLE amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K2000
Device Model: Hitachi HDS722020ALA330
Serial Number: JK1131YAHKZ0EV
LU WWN Device Id: 5 000cca 221d6427b
Firmware Version: JKAOA28A
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Aug 29 18:22:25 2013 MST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART STATUS RETURN: incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (21742) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 362) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 095 095 016 Pre-fail Always - 17
2 Throughput_Performance 0x0005 132 132 054 Pre-fail Offline - 103
3 Spin_Up_Time 0x0007 158 158 024 Pre-fail Always - 496 (Average 416)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 109
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 112 112 020 Pre-fail Offline - 39
9 Power_On_Hours 0x0012 096 096 000 Old_age Always - 30282
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 101
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 745
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 745
194 Temperature_Celsius 0x0002 153 153 000 Old_age Always - 39 (Min/Max 23/63)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 0
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 30276 -
# 2 Short offline Completed without error 00% 30264 -
# 3 Short offline Completed without error 00% 30252 -
# 4 Short offline Completed without error 00% 30240 -
# 5 Short offline Completed without error 00% 30228 -
# 6 Short offline Completed without error 00% 30216 -
# 7 Short offline Completed without error 00% 30204 -
# 8 Short offline Completed without error 00% 30192 -
# 9 Short offline Completed without error 00% 30180 -
#10 Short offline Completed without error 00% 30168 -
#11 Short offline Completed without error 00% 30156 -
#12 Short offline Completed without error 00% 30144 -
#13 Short offline Completed without error 00% 30132 -
#14 Short offline Completed without error 00% 30120 -
#15 Short offline Completed without error 00% 30108 -
#16 Short offline Completed without error 00% 30096 -
#17 Short offline Completed without error 00% 30084 -
#18 Short offline Completed without error 00% 30072 -
#19 Short offline Completed without error 00% 30060 -
#20 Short offline Completed without error 00% 30048 -
#21 Short offline Completed without error 00% 30036 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
[root@freenas] ~# smartctl -a /dev/da4
smartctl 6.1 2013-03-16 r3800 [FreeBSD 9.1-STABLE amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K2000
Device Model: Hitachi HDS722020ALA330
Serial Number: JK1131YAHL3LAV
LU WWN Device Id: 5 000cca 221d653aa
Firmware Version: JKAOA28A
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Aug 29 18:22:31 2013 MST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART STATUS RETURN: incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (23506) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 392) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 092 092 016 Pre-fail Always - 65576
2 Throughput_Performance 0x0005 132 132 054 Pre-fail Offline - 106
3 Spin_Up_Time 0x0007 156 156 024 Pre-fail Always - 505 (Average 424)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 129
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 112 112 020 Pre-fail Offline - 39
9 Power_On_Hours 0x0012 096 096 000 Old_age Always - 30320
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 119
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 918
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 918
194 Temperature_Celsius 0x0002 150 150 000 Old_age Always - 40 (Min/Max 22/57)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 0
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 30314 -
# 2 Short offline Completed without error 00% 30302 -
# 3 Short offline Completed without error 00% 30290 -
# 4 Short offline Completed without error 00% 30278 -
# 5 Short offline Completed without error 00% 30266 -
# 6 Short offline Completed without error 00% 30254 -
# 7 Short offline Completed without error 00% 30242 -
# 8 Short offline Completed without error 00% 30230 -
# 9 Short offline Completed without error 00% 30218 -
#10 Short offline Completed without error 00% 30206 -
#11 Short offline Completed without error 00% 30194 -
#12 Short offline Completed without error 00% 30182 -
#13 Short offline Completed without error 00% 30170 -
#14 Short offline Completed without error 00% 30158 -
#15 Short offline Completed without error 00% 30146 -
#16 Short offline Completed without error 00% 30134 -
#17 Short offline Completed without error 00% 30122 -
#18 Short offline Completed without error 00% 30110 -
#19 Short offline Completed without error 00% 30098 -
#20 Short offline Completed without error 00% 30086 -
#21 Short offline Completed without error 00% 30074 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
[root@freenas] ~#