How to enable smartd?

Status
Not open for further replies.
D

diskmaster23

Dabbler
Joined
May 13, 2013
Messages
16
I cannot seem to get smartd enabled. I get the error "Will not 'start' smartd because smartd_enable is NO'. When I 'service smartd start'. I try to edit /etc/rc.conf and the settings reset every time I reboot. I try to edit /tmp/rc.conf.freenas and the settings reset every time I reboot. I have even tried just creating a blank file and folder in etc, and it gets deleted upon reboot. I don't know why. I would like to enable smartd. I am running this on a hard drive. Installed from USB.

Please advise.
 
Bidule0hm

Bidule0hm

Server Electronics Sorcerer
Joined
Aug 5, 2013
Messages
3,710
Use the GUI to enable the SMART service, do not use the CLI for that.
 
D

diskmaster23

Dabbler
Joined
May 13, 2013
Messages
16
Code:
[root@freenas] ~# uname -a
FreeBSD freenas.local 9.3-RELEASE-p28 FreeBSD 9.3-RELEASE-p28 #0 r288272+f229c79: Sat Dec 12 11:58:01 PST 2015     root@build3.ixsystems.com:/tank/home/stable-builds/FN/objs/os-base/amd64/tank/home/stable-builds/FN/FreeBSD/src/sys/FREENAS.amd64  amd64



Code:
[root@freenas] /etc#  /etc/ix.rc.d/ix-smartd start
[root@freenas] /etc#


tail -n 10 /var/log/messages
Code:
Dec 15 16:42:38 freenas notifier: smartd not running? (check /var/run/smartd.pid).

Dec 15 16:42:38 freenas notifier: Will not 'restart' smartd because smartd_enable is NO.
Dec 15 16:42:55 freenas notifier: Starting smartd.
Dec 15 16:42:55 freenas smartd[8051]: Configuration file /usr/local/etc/smartd.conf parsed but has no entries (like /dev/hda)
Dec 15 16:42:55 freenas root: /usr/local/etc/rc.d/smartd: WARNING: failed to start smartd
Dec 15 16:42:55 freenas notifier: /usr/local/etc/rc.d/smartd: WARNING: failed to start smartd


Code:
[root@freenas] /etc# cat /usr/local/etc/smartd.conf
################################################
# smartd.conf generated by /etc/ix.rc.d/ix-smartd
################################################


Code:
[root@freenas] /etc# camcontrol devlist -v
scbus0 on ahcich0 bus 0:
<>                                 at scbus0 target -1 lun -1 ()
scbus1 on ahcich1 bus 0:
<ST9160827AS 3.CMG>                at scbus1 target 0 lun 0 (ada0,pass0)
<>                                 at scbus1 target -1 lun -1 ()
scbus2 on ahcich2 bus 0:
<>                                 at scbus2 target -1 lun -1 ()
scbus3 on ahcich3 bus 0:
<>                                 at scbus3 target -1 lun -1 ()
scbus4 on ahcich4 bus 0:
<>                                 at scbus4 target -1 lun -1 ()
scbus5 on ahcich5 bus 0:
<>                                 at scbus5 target -1 lun -1 ()
scbus6 on camsim0 bus 0:
<>                                 at scbus6 target -1 lun -1 ()
scbus7 on umass-sim0 bus 0:
<TOSHIBA TransMemory 1.00>         at scbus7 target 0 lun 0 (pass1,da0)
scbus-1 on xpt0 bus 0:
<>                                 at scbus-1 target -1 lun -1 (xpt0)


Code:
[root@freenas] ~# smartctl -a /dev/pass0
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p28 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Momentus 5400.4
Device Model:     ST9160827AS
Serial Number:    5RF33NTY
LU WWN Device Id: 5 000c50 01477a9cd
Firmware Version: 3.CMG
User Capacity:    160,041,885,696 bytes [160 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 2.6, 1.5 Gb/s
Local Time is:    Tue Dec 15 16:51:29 2015 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x82)    Offline data collection activity
                    was completed without error.
                    Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)    The previous self-test routine completed
                    without error or no self-test has ever
                    been run.
Total time to complete Offline
data collection:         (  426) seconds.
Offline data collection
capabilities:              (0x5b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    No Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine
recommended polling time:      (   1) minutes.
Extended self-test routine
recommended polling time:      (  60) minutes.
SCT capabilities:            (0x0001)    SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   094   059   034    Pre-fail  Always       -       236187915
  3 Spin_Up_Time            0x0003   100   099   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   079   079   020    Old_age   Always       -       22240
  5 Reallocated_Sector_Ct   0x0033   098   098   036    Pre-fail  Always       -       102
  7 Seek_Error_Rate         0x000f   081   060   030    Pre-fail  Always       -       4428332530
  9 Power_On_Hours          0x0032   066   066   000    Old_age   Always       -       30009 (184 176 0)
10 Spin_Retry_Count        0x0013   100   100   034    Pre-fail  Always       -       0
12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       977
184 End-to-End_Error        0x0032   100   253   000    Old_age   Always       -       0
187 Reported_Uncorrect      0x003a   001   001   000    Old_age   Always       -       2329
189 High_Fly_Writes         0x0022   001   001   045    Old_age   Always   FAILING_NOW 234
190 Airflow_Temperature_Cel 0x0032   065   036   000    Old_age   Always       -       35 (Min/Max 10/64)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       1565
192 Power-Off_Retract_Count 0x0022   100   001   000    Old_age   Always       -       69
193 Load_Cycle_Count        0x001a   089   089   000    Old_age   Always       -       22922
194 Temperature_Celsius     0x0012   035   064   000    Old_age   Always       -       35 (0 10 0 0 0)
195 Hardware_ECC_Recovered  0x0010   066   047   000    Old_age   Offline      -       236190989
196 Reallocated_Event_Count 0x003e   066   066   000    Old_age   Always       -       30054 (30598 0)
197 Current_Pending_Sector  0x0000   100   100   000    Old_age   Offline      -       18
198 Offline_Uncorrectable   0x0032   100   100   000    Old_age   Always       -       18
199 UDMA_CRC_Error_Count    0x0000   200   200   000    Old_age   Offline      -       0
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 Data_Address_Mark_Errs  0x0000   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 2333 (device log contains only the most recent five errors)
    CR = Command Register [HEX]
    FR = Features Register [HEX]
    SC = Sector Count Register [HEX]
    SN = Sector Number Register [HEX]
    CL = Cylinder Low Register [HEX]
    CH = Cylinder High Register [HEX]
    DH = Device/Head Register [HEX]
    DC = Device Command Register [HEX]
    ER = Error register [HEX]
    ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 2333 occurred at disk power-on lifetime: 25099 hours (1045 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 5e a8 24 e0  Error: UNC at LBA = 0x0024a85e = 2402398

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 30 50 a8 24 e0 00      03:50:35.891  READ DMA EXT
  27 00 00 00 00 00 e0 00      03:50:35.890  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      03:50:35.884  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      03:50:32.252  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      03:50:32.252  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 2332 occurred at disk power-on lifetime: 25099 hours (1045 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 5e a8 24 e0  Error: UNC at LBA = 0x0024a85e = 2402398

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 30 50 a8 24 e0 00      03:50:24.956  READ DMA EXT
  27 00 00 00 00 00 e0 00      03:50:24.955  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      03:50:24.948  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      03:50:32.252  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      03:50:32.252  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 2331 occurred at disk power-on lifetime: 25099 hours (1045 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 5e a8 24 e0  Error: UNC at LBA = 0x0024a85e = 2402398

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 30 50 a8 24 e0 00      03:50:24.956  READ DMA EXT
  27 00 00 00 00 00 e0 00      03:50:24.955  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      03:50:24.948  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      03:50:24.940  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      03:50:24.939  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 2330 occurred at disk power-on lifetime: 25099 hours (1045 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 5e a8 24 e0  Error: UNC at LBA = 0x0024a85e = 2402398

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 30 50 a8 24 e0 00      03:50:24.956  READ DMA EXT
  27 00 00 00 00 00 e0 00      03:50:24.955  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      03:50:24.948  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      03:50:24.940  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      03:50:24.939  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 2329 occurred at disk power-on lifetime: 25099 hours (1045 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 5e a8 24 e0  Error: UNC at LBA = 0x0024a85e = 2402398

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 30 50 a8 24 e0 00      03:50:17.477  READ DMA EXT
  27 00 00 00 00 00 e0 00      03:50:17.477  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      03:50:17.477  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      03:50:17.476  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      03:50:17.476  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Vendor (0x50)       Completed without error       00%         1         -

SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


Code:
[root@freenas] ~# smartctl -d auto -a /dev/pass0
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p28 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Momentus 5400.4
Device Model:     ST9160827AS
Serial Number:    5RF33NTY
LU WWN Device Id: 5 000c50 01477a9cd
Firmware Version: 3.CMG
User Capacity:    160,041,885,696 bytes [160 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 2.6, 1.5 Gb/s
Local Time is:    Tue Dec 15 16:52:17 2015 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x82)    Offline data collection activity
                    was completed without error.
                    Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)    The previous self-test routine completed
                    without error or no self-test has ever
                    been run.
Total time to complete Offline
data collection:         (  426) seconds.
Offline data collection
capabilities:              (0x5b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    No Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine
recommended polling time:      (   1) minutes.
Extended self-test routine
recommended polling time:      (  60) minutes.
SCT capabilities:            (0x0001)    SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   094   059   034    Pre-fail  Always       -       236187927
  3 Spin_Up_Time            0x0003   100   099   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   079   079   020    Old_age   Always       -       22240
  5 Reallocated_Sector_Ct   0x0033   098   098   036    Pre-fail  Always       -       102
  7 Seek_Error_Rate         0x000f   081   060   030    Pre-fail  Always       -       4428332551
  9 Power_On_Hours          0x0032   066   066   000    Old_age   Always       -       30009 (118 46 0)
10 Spin_Retry_Count        0x0013   100   100   034    Pre-fail  Always       -       0
12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       977
184 End-to-End_Error        0x0032   100   253   000    Old_age   Always       -       0
187 Reported_Uncorrect      0x003a   001   001   000    Old_age   Always       -       2329
189 High_Fly_Writes         0x0022   001   001   045    Old_age   Always   FAILING_NOW 234
190 Airflow_Temperature_Cel 0x0032   065   036   000    Old_age   Always       -       35 (Min/Max 10/64)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       1565
192 Power-Off_Retract_Count 0x0022   100   001   000    Old_age   Always       -       69
193 Load_Cycle_Count        0x001a   089   089   000    Old_age   Always       -       22922
194 Temperature_Celsius     0x0012   035   064   000    Old_age   Always       -       35 (0 10 0 0 0)
195 Hardware_ECC_Recovered  0x0010   066   047   000    Old_age   Offline      -       236191005
196 Reallocated_Event_Count 0x003e   066   066   000    Old_age   Always       -       30054 (13572 0)
197 Current_Pending_Sector  0x0000   100   100   000    Old_age   Offline      -       18
198 Offline_Uncorrectable   0x0032   100   100   000    Old_age   Always       -       18
199 UDMA_CRC_Error_Count    0x0000   200   200   000    Old_age   Offline      -       0
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 Data_Address_Mark_Errs  0x0000   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 2333 (device log contains only the most recent five errors)
    CR = Command Register [HEX]
    FR = Features Register [HEX]
    SC = Sector Count Register [HEX]
    SN = Sector Number Register [HEX]
    CL = Cylinder Low Register [HEX]
    CH = Cylinder High Register [HEX]
    DH = Device/Head Register [HEX]
    DC = Device Command Register [HEX]
    ER = Error register [HEX]
    ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 2333 occurred at disk power-on lifetime: 25099 hours (1045 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 5e a8 24 e0  Error: UNC at LBA = 0x0024a85e = 2402398

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 30 50 a8 24 e0 00      03:50:35.891  READ DMA EXT
  27 00 00 00 00 00 e0 00      03:50:35.890  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      03:50:35.884  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      03:50:32.252  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      03:50:32.252  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 2332 occurred at disk power-on lifetime: 25099 hours (1045 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 5e a8 24 e0  Error: UNC at LBA = 0x0024a85e = 2402398

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 30 50 a8 24 e0 00      03:50:24.956  READ DMA EXT
  27 00 00 00 00 00 e0 00      03:50:24.955  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      03:50:24.948  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      03:50:32.252  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      03:50:32.252  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 2331 occurred at disk power-on lifetime: 25099 hours (1045 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 5e a8 24 e0  Error: UNC at LBA = 0x0024a85e = 2402398

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 30 50 a8 24 e0 00      03:50:24.956  READ DMA EXT
  27 00 00 00 00 00 e0 00      03:50:24.955  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      03:50:24.948  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      03:50:24.940  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      03:50:24.939  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 2330 occurred at disk power-on lifetime: 25099 hours (1045 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 5e a8 24 e0  Error: UNC at LBA = 0x0024a85e = 2402398

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 30 50 a8 24 e0 00      03:50:24.956  READ DMA EXT
  27 00 00 00 00 00 e0 00      03:50:24.955  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      03:50:24.948  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      03:50:24.940  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      03:50:24.939  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 2329 occurred at disk power-on lifetime: 25099 hours (1045 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 5e a8 24 e0  Error: UNC at LBA = 0x0024a85e = 2402398

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 30 50 a8 24 e0 00      03:50:17.477  READ DMA EXT
  27 00 00 00 00 00 e0 00      03:50:17.477  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      03:50:17.477  IDENTIFY DEVICE
  ef 03 45 00 00 00 a0 00      03:50:17.476  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      03:50:17.476  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Vendor (0x50)       Completed without error       00%         1         -

SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
 
R

Robert Trevellyan

Pony Wrangler
Joined
May 16, 2014
Messages
3,778
This may have nothing to do with your original question, but your drive with serial #5RF33NTY is dying and must be replaced ASAP.
Aside from lots of bad sectors and more than 30,000 reallocation events ...
diskmaster23 said:
89 High_Fly_Writes 0x0022 001 001 045 Old_age Always FAILING_NOW 234
Click to expand...

Wait, are you running FreeNAS on a laptop?
 
SweetAndLow

SweetAndLow

Sweet'NASty
Joined
Nov 6, 2013
Messages
6,421
Did you create a smart test task? You might need that before you can turn it on.
 
D

diskmaster23

Dabbler
Joined
May 13, 2013
Messages
16
Robert Trevellyan said:
This may have nothing to do with your original question, but your drive with serial #5RF33NTY is dying and must be replaced ASAP.
Aside from lots of bad sectors and more than 30,000 reallocation events ...


Wait, are you running FreeNAS on a laptop?
Click to expand...

Well...crap..I didn't notice that. I just looked at the "Passed" part. I guess you could consider this to be a laptop drive. It is an 2.5" drive. I was gonna run it this way until I got a flash drive. Meanwhile, it still doesn't address my issue, but thanks for letting me know.
You think if I put this install on another drive that it might correct the smartd issue?
 
Ericloewe

Ericloewe

Server Wrangler
Moderator
Joined
Feb 15, 2014
Messages
20,194
diskmaster23 said:
Sure do. Got it setup on the GUI to do a short-test once a month.
Click to expand...
Well, your issues aside, that's a useless schedule. A monthly long test is the bare minimum you should do. Two long tests per month are better.

What is your hardware and FreeNAS version?

EDIT: *monthly* long test. Not daily. That would be excessive and detrimental to the drives.
 
Last edited:
Ericloewe

Ericloewe

Server Wrangler
Moderator
Joined
Feb 15, 2014
Messages
20,194
gpsguy said:
I presume that was a typo and you either meant to say "daily short" or "monthly long".
Click to expand...
Yup, already corrected.

Thanks for pointing it out, anyway. Don't want people getting the wrong idea. :p
 
R

Robert Trevellyan

Pony Wrangler
Joined
May 16, 2014
Messages
3,778
SweetAndLow said:
Did you create a smart test task? You might need that before you can turn it on.
Click to expand...
That would be weird. The service periodically checks the SMART attributes, while the scheduled tasks run self-tests. These should be completely independent.
diskmaster23 said:
It is an 2.5" drive
Click to expand...
So that's your boot drive? In that case, save your configuration and install FreeNAS on a different device, then throw this one away.
diskmaster23 said:
You think if I put this install on another drive that it might correct the smartd issue?
Click to expand...
Seems unlikely, but you never know.
 
D

diskmaster23

Dabbler
Joined
May 13, 2013
Messages
16
I've taken the advice and ordered an SATAIII SSD drive. Should be arriving in a few days. I'll try and see if these issues get cleared up with another new install; my problem was from a fresh install. I'll report back after the new install.
 
D

diskmaster23

Dabbler
Joined
May 13, 2013
Messages
16
Fresh install. Brand new SSD drive. Same issue as before. Not related to issues with drive.
Updated to the latest stable version.
Tried to run smartd from the GUI.
This is the error that was shown in log/messages
Code:
Dec 21 11:14:04 freenas smartd[5835]: Configuration file /usr/local/etc/smartd.conf parsed but has no entries (like /dev/hda)
Dec 21 11:14:04 freenas root: /usr/local/etc/rc.d/smartd: WARNING: failed to start smartd
Dec 21 11:14:04 freenas notifier: /usr/local/etc/rc.d/smartd: WARNING: failed to start smartd

I tried to add the drive to the smart test on the GUI. It doesn't even appear. I dunno why I cannot test the main OS drive, but help would be appreciated.
 
HoneyBadger

HoneyBadger

actually does care
Administrator
Moderator
iXsystems
Joined
Feb 6, 2014
Messages
5,112
I see "/dev/pass0" being listed, which implies you've got some manner of RAID in play. From your other thread I see you're using an ASRock Z77 board.

Have you absolutely confirmed that your SATA ports are set to AHCI, and there is no RAID setting enabled anywhere?

Also, this board does not support ECC memory.
 
D

diskmaster23

Dabbler
Joined
May 13, 2013
Messages
16
Running this again with the new drive.

Code:
[root@freenas] ~# camcontrol devlist -v
scbus0 on ahcich0 bus 0:
<>                                 at scbus0 target -1 lun -1 ()
scbus1 on ahcich1 bus 0:
<ADATA SP600 5.2>                  at scbus1 target 0 lun 0 (ada0,pass0)
<>                                 at scbus1 target -1 lun -1 ()
scbus2 on ahcich2 bus 0:
<>                                 at scbus2 target -1 lun -1 ()
scbus3 on ahcich3 bus 0:
<>                                 at scbus3 target -1 lun -1 ()
scbus4 on ahcich4 bus 0:
<>                                 at scbus4 target -1 lun -1 ()
scbus5 on ahcich5 bus 0:
<>                                 at scbus5 target -1 lun -1 ()
scbus6 on camsim0 bus 0:
<>                                 at scbus6 target -1 lun -1 ()
scbus-1 on xpt0 bus 0:
<>                                 at scbus-1 target -1 lun -1 (xpt0)


Confirmed running the AHCI mode in the BIOS for SATA. Please see photos.
GZ3pOic.jpg

ECC memory is not used. Running regular non-ECC DDR3-1600. Total of 8GiB.
Correct. I am running the Asrock Z77 Extreme 3 motherboard with an Intel Celeron CPU 1610 @ 2.60GHz.
Latest BIOS as well.
 
HoneyBadger

HoneyBadger

actually does care
Administrator
Moderator
iXsystems
Joined
Feb 6, 2014
Messages
5,112
If you do smartctl -d auto -a /dev/ada0 do you get results back? That would mean that AHCI is fine.

Try manually adding the line in smartd.conf for

Code:
/dev/ada0 -a -n never -W 0,0,0


Not sure why the auto-script wouldn't have found them.

The motherboard choice and non-ECC RAM is another point entirely though.
 
D

diskmaster23

Dabbler
Joined
May 13, 2013
Messages
16
Runs just fine.
Code:
[root@freenas] ~# smartctl -d auto -a /dev/ada0
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p28 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     JMicron based SSDs
Device Model:     ADATA SP600
Serial Number:    2F4520060067
LU WWN Device Id: 5 707c18 1001eecd3
Firmware Version: 5.2
User Capacity:    32,017,047,552 bytes [32.0 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Form Factor:      < 1.8 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Mon Dec 21 12:17:45 2015 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)    Offline data collection activity
                    was never started.
                    Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)    The previous self-test routine completed
                    without error or no self-test has ever
                    been run.
Total time to complete Offline
data collection:         (   32) seconds.
Offline data collection
capabilities:              (0x5b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine
recommended polling time:      (   1) minutes.
Extended self-test routine
recommended polling time:      (   1) minutes.
SCT capabilities:            (0x0039)    SCT Status supported.
                    SCT Error Recovery Control supported.
                    SCT Feature Control supported.
                    SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000a   100   100   000    Old_age   Always       -       0
  2 Throughput_Performance  0x0005   100   100   050    Pre-fail  Offline      -       0
  3 Unknown_Attribute       0x0007   100   100   050    Pre-fail  Always       -       0
  5 Reallocated_Sector_Ct   0x0013   100   100   050    Pre-fail  Always       -       0
  7 Unknown_Attribute       0x000b   100   100   050    Pre-fail  Always       -       0
  8 Unknown_Attribute       0x0005   100   100   050    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0012   100   100   000    Old_age   Always       -       1
10 Unknown_Attribute       0x0013   100   100   050    Pre-fail  Always       -       0
12 Power_Cycle_Count       0x0012   100   100   000    Old_age   Always       -       4
167 Unknown_Attribute       0x0022   100   100   000    Old_age   Always       -       0
168 SATA_Phy_Error_Count    0x0012   100   100   000    Old_age   Always       -       3
169 Unknown_Attribute       0x0013   100   100   010    Pre-fail  Always       -       0
170 Bad_Block_Count         0x0013   100   100   010    Pre-fail  Always       -       0 0 0
173 Erase_Count             0x0012   199   199   000    Old_age   Always       -       2 3 2
175 Bad_Cluster_Table_Count 0x0013   100   100   010    Pre-fail  Always       -       0
180 Unused_Rsvd_Blk_Cnt_Tot 0x0033   100   100   020    Pre-fail  Always       -       138
192 Unexpect_Power_Loss_Ct  0x0012   100   100   000    Old_age   Always       -       2
194 Temperature_Celsius     0x0022   073   073   030    Old_age   Always       -       27 (Min/Max 25/27)
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
231 Temperature_Celsius     0x0033   100   100   005    Pre-fail  Always       -       0
233 Media_Wearout_Indicator 0x0032   100   100   000    Old_age   Always       -       129933184
234 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       128325696
240 Unknown_Attribute       0x0013   100   100   050    Pre-fail  Always       -       0
241 Total_LBAs_Written      0x0032   100   100   000    Old_age   Always       -       129173099
242 Total_LBAs_Read         0x0032   100   100   000    Old_age   Always       -       126802369

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


Adding that code to smartd.conf and the smartd daemon started up just fine, but it still isn't listed in the GUI for SMART tests.

I admit the board, memory, or CPU isn't ideal, but I am working with what extra parts I have laying around. I'll be upgrading in the future.

Thanks for your help. Strange the script didn't find it.
 
D

diskmaster23

Dabbler
Joined
May 13, 2013
Messages
16
Spoke too soon. Rebooted. Smartd.conf resetted back to blank.
This has been an issue. I can't get the manual settings to hold.
 
Status
Not open for further replies.

Important Announcement for the TrueNAS Community.

The TrueNAS Community has now been moved. This forum will now become READ-ONLY for historical purposes. Please feel free to join us on the new TrueNAS Community Forums.

Related topics on forums.truenas.com for thread: "How to enable smartd?"

Similar threads

W
  • Locked
smartd deamon not starting
Replies
4
Views
2K
WillD
W
Ericloewe
  • Locked
smartd failing to start [Including workaround!]
Replies
5
Views
1K
Ericloewe
Ericloewe
M
SmartD Errors when trying to replace a drive
Replies
0
Views
631
mortis2600
M
P
SOLVED How to configure smartd to ignore a SMART attribute?
2
Replies
24
Views
6K
sretalla
sretalla
J
  • Locked
SOLVED smartd is not sending an alert/email
Replies
0
Views
1K
Juggernaut
J
Top