Hi,
i am having trouble to get my debian iohyve VM to connect to my local network.
My goal is to install a roon core server, and i am following this tutorial: https://community.roonlabs.com/t/howto-debian-installation-on-frenas-bhyve/10591
My current configuration is :
FreeNAS-11.1-U2 - X11SSM-F supermicro - 2x16Gb kinston - 4x4Tb WD drives + 2x2Tb drives
my motherboard is a Supermicro X10SL7-F and according to the manual, this is the lan interface:
2x RJ45 Gigabit Ethernet LAN ports
1x RJ45 Dedicated IPMI LAN port
https://www.supermicro.com/products/motherboard/xeon/c220/x10sl7-f.cfm
And this is my ifconfig
Iam not very familiar with this output and how to read it properly.
according to the tutorial i need to setup this line in the tunables to setup the network bridge. In my case i don't have an interface named em0, so which one i must use ?
similar question for this line
In my case which interface i should point iohyve to?
Lastly, within the debian VM, this the current configuration i am using:
/etc/network/interfaces
# ip a show
Any advice is most welcomed! thanks in advance!
i am having trouble to get my debian iohyve VM to connect to my local network.
My goal is to install a roon core server, and i am following this tutorial: https://community.roonlabs.com/t/howto-debian-installation-on-frenas-bhyve/10591
My current configuration is :
FreeNAS-11.1-U2 - X11SSM-F supermicro - 2x16Gb kinston - 4x4Tb WD drives + 2x2Tb drives
my motherboard is a Supermicro X10SL7-F and according to the manual, this is the lan interface:
2x RJ45 Gigabit Ethernet LAN ports
1x RJ45 Dedicated IPMI LAN port
https://www.supermicro.com/products/motherboard/xeon/c220/x10sl7-f.cfm
And this is my ifconfig
igb0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=6403bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6>
ether 0c:c4:7a:86:67:d8
hwaddr 0c:c4:7a:86:67:d8
nd6 options=9<PERFORMNUD,IFDISABLED>
media: Ethernet autoselect
status: no carrier
igb1: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=2400b9<RXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,VLAN_HWTSO,RXCSUM_IPV6>
ether 0c:c4:7a:86:67:d9
hwaddr 0c:c4:7a:86:67:d9
inet 192.168.1.5 netmask 0xffffff00 broadcast 192.168.1.255
nd6 options=9<PERFORMNUD,IFDISABLED>
media: Ethernet autoselect (1000baseT )
status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
inet 127.0.0.1 netmask 0xff000000
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
groups: lo
tap1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
description: iohyve-roon–
options=80000
ether 00:bd:f0:0e:f8:01
hwaddr 00:bd:f0:0e:f8:01
nd6 options=9<PERFORMNUD,IFDISABLED>
media: Ethernet autoselect
status: no carrier
groups: tap
tap2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
description: iohyve-roonserver–
options=80000
ether 00:bd:bc:24:f8:02
hwaddr 00:bd:bc:24:f8:02
inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
nd6 options=9<PERFORMNUD,IFDISABLED>
media: Ethernet autoselect
status: active
groups: tap
Opened by PID 6707
bridge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 02:0d:36:85:fc:00
nd6 options=1
groups: bridge
id 00:00:00:00:00:00 priority 32768 hellotime 2 fwddelay 15
maxage 20 holdcnt 6 proto rstp maxaddr 2000 timeout 1200
root id 00:00:00:00:00:00 priority 32768 ifcost 0 port 0
member: tap3 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 12 priority 128 path cost 2000000
member: epair3a flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 10 priority 128 path cost 2000
member: epair2a flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 9 priority 128 path cost 2000
member: epair1a flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 8 priority 128 path cost 2000
member: epair0a flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 7 priority 128 path cost 2000
member: igb1 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 2 priority 128 path cost 20000
epair0a: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8<VLAN_MTU>
ether 02:7b:50:00:07:0a
hwaddr 02:7b:50:00:07:0a
nd6 options=1
media: Ethernet 10Gbase-T (10Gbase-T )
status: active
groups: epair
epair1a: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8<VLAN_MTU>
ether 02:7b:50:00:08:0a
hwaddr 02:7b:50:00:08:0a
nd6 options=1
media: Ethernet 10Gbase-T (10Gbase-T )
status: active
groups: epair
epair2a: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8<VLAN_MTU>
ether 02:7b:50:00:09:0a
hwaddr 02:7b:50:00:09:0a
nd6 options=1
media: Ethernet 10Gbase-T (10Gbase-T )
status: active
groups: epair
epair3a: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8<VLAN_MTU>
ether 02:7b:50:00:0a:0a
hwaddr 02:7b:50:00:0a:0a
nd6 options=1
media: Ethernet 10Gbase-T (10Gbase-T )
status: active
groups: epair
tap3: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=80000
ether 00:bd:70:c8:f8:03
hwaddr 00:bd:70:c8:f8:03
nd6 options=1
media: Ethernet autoselect
status: active
groups: tap
Opened by PID 10966
Iam not very familiar with this output and how to read it properly.
according to the tutorial i need to setup this line in the tunables to setup the network bridge. In my case i don't have an interface named em0, so which one i must use ?
iohyve_flags="kmod=1 net=em0"
similar question for this line
iohyve setup net=em0
In my case which interface i should point iohyve to?
Lastly, within the debian VM, this the current configuration i am using:
/etc/network/interfaces
# The loopback network interface
auto lo0
#iface lo0 inet loopback
#My IP description
#IPv4 address
auto enp0s3
iface enp0s3 inet static
address 192.168.1.100
netmask 255.255.255.0
#network 192.168.1.0
#broadcast 192.168.1.255
gateway 192.168.1.1
# ip a show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: enp0s3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:a0:98:ba:de:1f brd ff:ff:ff:ff:ff:ff
inet 192.168.1.100/24 brd 192.168.1.255 scope global enp0s3
valid_lft forever preferred_lft forever
inet6 fe80::2a0:98ff:feba:de1f/64 scope link
valid_lft forever preferred_lft forever
Any advice is most welcomed! thanks in advance!