SOLVED Encrypted volume not detected following reboot/upgrade

[Spec]

Hi,

My FreeNAS system has run fine for about 200 days. I wanted to upgrade from 9.10 to 9.10.2u6.
I shutdown all the jails, turned off all services and proceeded to upgrade to 9.10.2u6. After rebooting I couldn't get one of my 3 volumes to unlock/import.
ada0 = SSD1 - Single SSD (jails)
ada1 = OS/Boot - Single SSD
da0-5 = Data1 - 6 disk WD Red RAIDZ2
ada2/3 = Data2 - 2 disk WD Red RAIDZ0

When I came to unlock each volume I found the following:
Data2 - Unlocked OK with passphrase.
Data1 - couldn't be found when attempting to unlock, so I detached it and re-imported as per the manual - unlocked OK with encryption key file + passphrase.
SSD1 - couldn't be found when attempting to unlock, so I did the same as above, but when following the 'Import Volume' wizard, it couldn't be found.

I booted to my original installation and restored my configuration with the same problem.

The disk is available to be set up as a new volume, or can be used with 'Import Disk' but obviously I'd prefer to recover the volume where possible.
It doesn't have any critical data on it, but it would save a few hours setting up the jails again.

Any help appreciated.
Thanks

 

[m0nkey_]

In order to mount an encrypted pool, you must supply the keys you previously backed up when originally setting up the pool.

 

[Spec]

I did that with data1 and it worked but when I came to do the same with volume 'SSD1', the wizard at step 2 of 3 doesn't list any disks to choose from for me to use the encryption key and passphrase with.

 

[m0nkey_]

Can you provide details of your hardware configuration, CPU, motherboard, RAM and any HBAs you have?

Also provide output of camcontrol devlist and paste using the [ code ] tags

 

[Spec]

FreeNAS-9.10.2-U6 (561f0d7a1)
Supermicro X10SL7-F Firmware Revision : 03.27 BIOS Version : 3.0a
4x 8GB ECC
Intel(R) Xeon(R) CPU E3-1271 v3 @ 3.60GHz
Using the onboard HBA's in non-RAID mode (firmware flashed)

camcontrol devlist:

Code:

<ATA WDC WD60EFRX-68L 0A82>		at scbus0 target 0 lun 0 (pass0,da0)
<ATA WDC WD60EFRX-68L 0A82>		at scbus0 target 1 lun 0 (pass1,da1)
<ATA WDC WD60EFRX-68L 0A82>		at scbus0 target 2 lun 0 (pass2,da2)
<ATA WDC WD60EFRX-68L 0A82>		at scbus0 target 3 lun 0 (pass3,da3)
<ATA WDC WD60EFRX-68L 0A82>		at scbus0 target 4 lun 0 (pass4,da4)
<ATA WDC WD60EFRX-68L 0A82>		at scbus0 target 5 lun 0 (pass5,da5)
<INTEL SSDSA2M080G2GC 2CV102M3>	at scbus1 target 0 lun 0 (pass6,ada0)
<INTEL SSDSA2M080G2GC 2CV102M3>	at scbus2 target 0 lun 0 (pass7,ada1)
<WDC WD40EFRX-68N32N0 82.00A82>	at scbus3 target 0 lun 0 (pass8,ada2)
<WDC WD40EFRX-68N32N0 82.00A82>	at scbus4 target 0 lun 0 (pass9,ada3)

 

[Stux]

I recall there being some bug with multiple encrypted pools.

Suggest trying FN11.

 

[Spec]

Thanks for that - upgraded to FreeNAS-11.0-U3 (c5dcf4416) and I can import/unlock all 3 volumes now!

 

[Artion]

Thanks for that - upgraded to FreeNAS-11.0-U3 (c5dcf4416) and I can import/unlock all 3 volumes now!

Is this thread solved? Qonsider marking it as Solved. [emoji1]

Inviato dal mio YD201 utilizzando Tapatalk