ATA error count increased - What is wrong?

M

mruby

Dabbler
Joined
Nov 2, 2015
Messages
29
Ok, so I bought a motherboard, I believe one of the suggested ones in the hardware post. The motherboard I got is:
MBD-X9SRH-7F-O_SuperMicro mbd ATX C602J LGA2011 256GB DDR3 1600MHz SAS2
Click to expand...

I also purchased the suggested raid card:
IBM SERVERAID M1015 ADAPTER PCI-E 2.0 X8 RAID CONTROLLER CARD 46M0861-LOW P
Click to expand...

I've been running this setup for about 11 months (since Jan. of this year). And recently, like the past month, I started getting ATA errors all the time. It started on just a couple of drives, then later that day, a couple more, so I thought I had crap luck and my drives were going bad. I swapped them out for some new ones I had laying around as spares, and resilvered the volumes. It didn't even take a day before I started getting errors again. And pretty soon, I started getting emails from my freenas box with the following:

Device: /dev/ada2, ATA error count increased from 32 to 33
Device: /dev/da3 [SAT], ATA error count increased from 3 to 6
Device: /dev/ada5, ATA error count increased from 4 to 5
Device: /dev/da5 [SAT], ATA error count increased from 6 to 7
Device: /dev/da4 [SAT], ATA error count increased from 0 to 1
Device: /dev/da6 [SAT], ATA error count increased from 1 to 2
Device: /dev/ada4, ATA error count increased from 59 to 60
Device: /dev/da1 [SAT], ATA error count increased from 2 to 4
Device: /dev/da0 [SAT], ATA error count increased from 3 to 4
Device: /dev/da7 [SAT], ATA error count increased from 2 to 3
Click to expand...

I did some reading, and most posts said that the drives are about to fail. I did long smart tests on a few of the drives I pulled and replaced, and all came back ok on the test. I came across one post that suggested the cables being zip tied together can cause issues because sata cables aren't shielded. I thought that sounded weird, but I opened the case up, cut the zip tie and spread cables all over the place to make sure that wasn't the problem. No change.

So, what I gathered from this, was that I am getting these errors from all 10 ports on the supermicro motherboard. I do not believe that any of these disks are on the IBM m1015. This seems telling, but I'm not sure what would be causing it, or how to go about fixing it. My FreeBSD / Freenas skills are very limited. I stick to GUI as much as possible, but I am comfortable in terminal so long as I know what I need to do. Any pointers would be very helpful!

Thanks in advance!
 
Sakuru

Sakuru

Guru
Joined
Nov 20, 2015
Messages
527
What brand and model are the drives? Do they all have adequate cooling? Is there any excessive vibration in the chassis?
 
R

Robert Trevellyan

Pony Wrangler
Joined
May 16, 2014
Messages
3,778
ATA errors can be caused by something other than the drives: cables, power etc. It would be strange to have a whole bunch of drives start failing at the exact same time.
mruby said:
I am getting these errors from all 10 ports on the supermicro motherboard
Click to expand...
Are they by any chance Marvell controller ports?
mruby said:
Any pointers would be very helpful!
Click to expand...
It will be easier for people to help you if you post your full hardware specs, pool configuration and status, SMART output etc., per forum rules.
 
Ericloewe

Ericloewe

Server Wrangler
Moderator
Joined
Feb 15, 2014
Messages
20,194
Post the output of smartctl -a /dev/$drive_names
 
M

mruby

Dabbler
Joined
Nov 2, 2015
Messages
29
What brand and model are the drives? Do they all have adequate cooling? Is there any excessive vibration in the chassis?
Click to expand...
1. Hitachi Deskstar
2. Yes, it is about 50 degrees F. down where the chassis is, and I have quite a few very loud (high cpm) fans.
3. No vibration

ATA errors can be caused by something other than the drives: cables, power etc. It would be strange to have a whole bunch of drives start failing at the exact same time.
Click to expand...
Agreed. Seems pretty strange to me.

Are they by any chance Marvell controller ports?
Click to expand...
I don't think so, but how is the easiest way for me to check? Here is the supermicro board I have with its specs.
http://www.supermicro.com/products/motherboard/Xeon/C600/X9SRH-7F.cfm
It says "SAS2 via LSI 2308". I am guessing that is it right there.

It will be easier for people to help you if you post your full hardware specs, pool configuration and status, SMART output etc., per forum rules.
Click to expand...
Sorry, I thought I included the pertinent information. The drives that are throwing errors are split between 2 pools. Each with RaidZ2 (6 drives in each array). They are both healthy at the moment. Strangely, 4 of the drives throwing errors on are one array (with 2 not throwing any) and the other 6 are on the other array (all the drives in that array). I have a third RaidZ2 pool with 6 drives, and none of those are throwing errors. These are all on the m1015 card.

I will say though that I just started getting an unreadable sector warning yesterday on one drive. I've been getting the ata error notifications for at least a month though, and every drive I did SMART test on has not returned any problems.

Are there any other specific specs that would be useful? I'm new to this, so not really sure what info to provide.

I have a Long SMART running twice a month, and a short SMART running 4 times a month. I assume since I do not receive any emails, that these tests are not uncovering any issues.

Post the output of smartctl -a /dev/$drive_names
Click to expand...
Thanks for the hint on the command to run. I've saved output of all 10 drives to files. Silly problem, but I cannot seem to successfully copy paste them all. I'm using VI. I tried copying to buffer which did not seem to do anything :)%y). I also tried xclip (xclip -sel clip < ./smart_ada2) which appears that xclip is not available in freebsd. Stupid question, but what is easiest way to copy output to clipboard?


Thanks so much for the replies!
 
Last edited:
Bidule0hm

Bidule0hm

Server Electronics Sorcerer
Joined
Aug 5, 2013
Messages
3,710
Just select the text you want to copy, it'll automatically be put in the clipboard ;)
 
M

mruby

Dabbler
Joined
Nov 2, 2015
Messages
29
Just select the text you want to copy, it'll automatically be put in the clipboard ;)
Click to expand...
I can only select what I can see on screen. In this case, the output is 2 or 3 pages worth.

Thanks
 
Bidule0hm

Bidule0hm

Server Electronics Sorcerer
Joined
Aug 5, 2013
Messages
3,710
Use less (like this: your command | less) and use the up/down arrows to scroll (space bar to scroll a whole page) and Q to quit ;)
 
M

mruby

Dabbler
Joined
Nov 2, 2015
Messages
29
Output of
Code:
smartctl -a /dev/$drive_names


ada2
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p28 amd64] (local build)

Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org


=== START OF INFORMATION SECTION ===

Model Family:     Hitachi Deskstar 7K3000

Device Model:     Hitachi HDS723020BLA642

Serial Number:    MN1220F3157D6D

LU WWN Device Id: 5 000cca 369d0791d

Firmware Version: MN6OA580

User Capacity:    2,000,398,934,016 bytes [2.00 TB]

Sector Size:      512 bytes logical/physical

Rotation Rate:    7200 rpm

Form Factor:      3.5 inches

Device is:        In smartctl database [for details use: -P show]

ATA Version is:   ATA8-ACS T13/1699-D revision 4

SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)

Local Time is:    Fri Dec 11 10:44:57 2015 PST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled


=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED


General SMART Values:

Offline data collection status:  (0x84)Offline data collection activity

was suspended by an interrupting command from host.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (   0)The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (19808) seconds.

Offline data collection

capabilities:  (0x5b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003)Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01)Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time:  (   1) minutes.

Extended self-test routine

recommended polling time:  ( 330) minutes.

SCT capabilities:        (0x003d)SCT Status supported.

SCT Error Recovery Control supported.

SCT Feature Control supported.

SCT Data Table supported.


SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always       -       0

  2 Throughput_Performance  0x0005   135   135   054    Pre-fail  Offline      -       84

  3 Spin_Up_Time            0x0007   133   133   024    Pre-fail  Always       -       431 (Average 430)

  4 Start_Stop_Count        0x0012   099   099   000    Old_age   Always       -       5234

  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0

  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0

  8 Seek_Time_Performance   0x0005   133   133   020    Pre-fail  Offline      -       27

  9 Power_On_Hours          0x0012   097   097   000    Old_age   Always       -       25464

10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0

12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       108

192 Power-Off_Retract_Count 0x0032   088   088   000    Old_age   Always       -       14448

193 Load_Cycle_Count        0x0012   088   088   000    Old_age   Always       -       14448

194 Temperature_Celsius     0x0002   253   253   000    Old_age   Always       -       22 (Min/Max 12/62)

196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0

197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0

198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0

199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0


SMART Error Log Version: 1

ATA Error Count: 61 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.


Error 61 occurred at disk power-on lifetime: 25409 hours (1058 days + 17 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 71 87 27 4a 04  Error: UNC at LBA = 0x044a2787 = 71968647


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 70 88 27 4a 44 ff   4d+03:03:12.404  READ FPDMA QUEUED

  60 00 48 f8 28 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 40 f8 27 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 38 f8 26 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 30 f8 25 4a 40 00   4d+03:03:12.401  READ FPDMA QUEUED


Error 60 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 a1 0f 5e ab 0d  Error: UNC at LBA = 0x0dab5e0f = 229334543


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 a0 10 5e ab 4d ff   4d+01:33:08.442  READ FPDMA QUEUED

  60 00 e8 b0 5e ab 40 00   4d+01:33:08.441  READ FPDMA QUEUED

  60 00 e0 b0 5d ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d8 b0 5c ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d0 b0 5b ab 40 00   4d+01:33:08.439  READ FPDMA QUEUED


Error 59 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 b1 c7 94 aa 0d  Error: UNC at LBA = 0x0daa94c7 = 229283015


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 b0 c8 94 aa 4d ff   4d+01:30:07.650  READ FPDMA QUEUED

  60 00 28 78 96 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 20 78 95 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 18 78 94 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 10 78 93 aa 40 00   4d+01:30:07.647  READ FPDMA QUEUED


Error 58 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 c1 07 c9 a9 0d  Error: UNC at LBA = 0x0da9c907 = 229230855


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 c0 08 c9 a9 4d ff   4d+01:26:28.842  READ FPDMA QUEUED

  60 00 68 c8 ca a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 60 c8 c9 a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 58 c8 c8 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED

  60 00 50 c8 c7 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED


Error 57 occurred at disk power-on lifetime: 25406 hours (1058 days + 14 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 31 17 c0 cb 05  Error: UNC at LBA = 0x05cbc017 = 97239063


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 30 18 c0 cb 45 ff   4d+00:26:08.686  READ FPDMA QUEUED

  60 00 08 48 c1 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 00 48 c0 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 f8 48 bf cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED

  60 00 f0 48 be cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED


SMART Self-test log structure revision number 1

Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error

# 1  Short offline       Completed without error       00%     25452         -

# 2  Short offline       Completed without error       00%     25423         -


SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.


ada4
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p28 amd64] (local build)

Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org


=== START OF INFORMATION SECTION ===

Model Family:     Hitachi Deskstar 7K3000

Device Model:     Hitachi HDS723020BLA642

Serial Number:    MN1220F3157D6D

LU WWN Device Id: 5 000cca 369d0791d

Firmware Version: MN6OA580

User Capacity:    2,000,398,934,016 bytes [2.00 TB]

Sector Size:      512 bytes logical/physical

Rotation Rate:    7200 rpm

Form Factor:      3.5 inches

Device is:        In smartctl database [for details use: -P show]

ATA Version is:   ATA8-ACS T13/1699-D revision 4

SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)

Local Time is:    Fri Dec 11 10:45:39 2015 PST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled


=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED


General SMART Values:

Offline data collection status:  (0x84)Offline data collection activity

was suspended by an interrupting command from host.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (   0)The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (19808) seconds.

Offline data collection

capabilities:  (0x5b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003)Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01)Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time:  (   1) minutes.

Extended self-test routine

recommended polling time:  ( 330) minutes.

SCT capabilities:        (0x003d)SCT Status supported.

SCT Error Recovery Control supported.

SCT Feature Control supported.

SCT Data Table supported.


SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always       -       0

  2 Throughput_Performance  0x0005   135   135   054    Pre-fail  Offline      -       84

  3 Spin_Up_Time            0x0007   133   133   024    Pre-fail  Always       -       431 (Average 430)

  4 Start_Stop_Count        0x0012   099   099   000    Old_age   Always       -       5234

  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0

  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0

  8 Seek_Time_Performance   0x0005   133   133   020    Pre-fail  Offline      -       27

  9 Power_On_Hours          0x0012   097   097   000    Old_age   Always       -       25464

10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0

12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       108

192 Power-Off_Retract_Count 0x0032   088   088   000    Old_age   Always       -       14448

193 Load_Cycle_Count        0x0012   088   088   000    Old_age   Always       -       14448

194 Temperature_Celsius     0x0002   253   253   000    Old_age   Always       -       22 (Min/Max 12/62)

196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0

197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0

198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0

199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0


SMART Error Log Version: 1

ATA Error Count: 61 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.


Error 61 occurred at disk power-on lifetime: 25409 hours (1058 days + 17 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 71 87 27 4a 04  Error: UNC at LBA = 0x044a2787 = 71968647


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 70 88 27 4a 44 ff   4d+03:03:12.404  READ FPDMA QUEUED

  60 00 48 f8 28 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 40 f8 27 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 38 f8 26 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 30 f8 25 4a 40 00   4d+03:03:12.401  READ FPDMA QUEUED


Error 60 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 a1 0f 5e ab 0d  Error: UNC at LBA = 0x0dab5e0f = 229334543


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 a0 10 5e ab 4d ff   4d+01:33:08.442  READ FPDMA QUEUED

  60 00 e8 b0 5e ab 40 00   4d+01:33:08.441  READ FPDMA QUEUED

  60 00 e0 b0 5d ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d8 b0 5c ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d0 b0 5b ab 40 00   4d+01:33:08.439  READ FPDMA QUEUED


Error 59 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 b1 c7 94 aa 0d  Error: UNC at LBA = 0x0daa94c7 = 229283015


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 b0 c8 94 aa 4d ff   4d+01:30:07.650  READ FPDMA QUEUED

  60 00 28 78 96 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 20 78 95 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 18 78 94 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 10 78 93 aa 40 00   4d+01:30:07.647  READ FPDMA QUEUED


Error 58 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 c1 07 c9 a9 0d  Error: UNC at LBA = 0x0da9c907 = 229230855


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 c0 08 c9 a9 4d ff   4d+01:26:28.842  READ FPDMA QUEUED

  60 00 68 c8 ca a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 60 c8 c9 a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 58 c8 c8 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED

  60 00 50 c8 c7 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED


Error 57 occurred at disk power-on lifetime: 25406 hours (1058 days + 14 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 31 17 c0 cb 05  Error: UNC at LBA = 0x05cbc017 = 97239063


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 30 18 c0 cb 45 ff   4d+00:26:08.686  READ FPDMA QUEUED

  60 00 08 48 c1 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 00 48 c0 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 f8 48 bf cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED

  60 00 f0 48 be cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED


SMART Self-test log structure revision number 1

Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error

# 1  Short offline       Completed without error       00%     25452         -

# 2  Short offline       Completed without error       00%     25423         -


SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.


ada5
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p28 amd64] (local build)

Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org


=== START OF INFORMATION SECTION ===

Model Family:     Hitachi Deskstar 7K3000

Device Model:     Hitachi HDS723020BLA642

Serial Number:    MN1220F3157D6D

LU WWN Device Id: 5 000cca 369d0791d

Firmware Version: MN6OA580

User Capacity:    2,000,398,934,016 bytes [2.00 TB]

Sector Size:      512 bytes logical/physical

Rotation Rate:    7200 rpm

Form Factor:      3.5 inches

Device is:        In smartctl database [for details use: -P show]

ATA Version is:   ATA8-ACS T13/1699-D revision 4

SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)

Local Time is:    Fri Dec 11 10:45:10 2015 PST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled


=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED


General SMART Values:

Offline data collection status:  (0x84)Offline data collection activity

was suspended by an interrupting command from host.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (   0)The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (19808) seconds.

Offline data collection

capabilities:  (0x5b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003)Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01)Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time:  (   1) minutes.

Extended self-test routine

recommended polling time:  ( 330) minutes.

SCT capabilities:        (0x003d)SCT Status supported.

SCT Error Recovery Control supported.

SCT Feature Control supported.

SCT Data Table supported.


SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always       -       0

  2 Throughput_Performance  0x0005   135   135   054    Pre-fail  Offline      -       84

  3 Spin_Up_Time            0x0007   133   133   024    Pre-fail  Always       -       431 (Average 430)

  4 Start_Stop_Count        0x0012   099   099   000    Old_age   Always       -       5234

  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0

  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0

  8 Seek_Time_Performance   0x0005   133   133   020    Pre-fail  Offline      -       27

  9 Power_On_Hours          0x0012   097   097   000    Old_age   Always       -       25464

10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0

12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       108

192 Power-Off_Retract_Count 0x0032   088   088   000    Old_age   Always       -       14448

193 Load_Cycle_Count        0x0012   088   088   000    Old_age   Always       -       14448

194 Temperature_Celsius     0x0002   253   253   000    Old_age   Always       -       22 (Min/Max 12/62)

196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0

197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0

198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0

199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0


SMART Error Log Version: 1

ATA Error Count: 61 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.


Error 61 occurred at disk power-on lifetime: 25409 hours (1058 days + 17 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 71 87 27 4a 04  Error: UNC at LBA = 0x044a2787 = 71968647


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 70 88 27 4a 44 ff   4d+03:03:12.404  READ FPDMA QUEUED

  60 00 48 f8 28 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 40 f8 27 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 38 f8 26 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 30 f8 25 4a 40 00   4d+03:03:12.401  READ FPDMA QUEUED


Error 60 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 a1 0f 5e ab 0d  Error: UNC at LBA = 0x0dab5e0f = 229334543


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 a0 10 5e ab 4d ff   4d+01:33:08.442  READ FPDMA QUEUED

  60 00 e8 b0 5e ab 40 00   4d+01:33:08.441  READ FPDMA QUEUED

  60 00 e0 b0 5d ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d8 b0 5c ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d0 b0 5b ab 40 00   4d+01:33:08.439  READ FPDMA QUEUED


Error 59 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 b1 c7 94 aa 0d  Error: UNC at LBA = 0x0daa94c7 = 229283015


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 b0 c8 94 aa 4d ff   4d+01:30:07.650  READ FPDMA QUEUED

  60 00 28 78 96 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 20 78 95 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 18 78 94 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 10 78 93 aa 40 00   4d+01:30:07.647  READ FPDMA QUEUED


Error 58 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 c1 07 c9 a9 0d  Error: UNC at LBA = 0x0da9c907 = 229230855


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 c0 08 c9 a9 4d ff   4d+01:26:28.842  READ FPDMA QUEUED

  60 00 68 c8 ca a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 60 c8 c9 a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 58 c8 c8 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED

  60 00 50 c8 c7 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED


Error 57 occurred at disk power-on lifetime: 25406 hours (1058 days + 14 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 31 17 c0 cb 05  Error: UNC at LBA = 0x05cbc017 = 97239063


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 30 18 c0 cb 45 ff   4d+00:26:08.686  READ FPDMA QUEUED

  60 00 08 48 c1 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 00 48 c0 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 f8 48 bf cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED

  60 00 f0 48 be cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED


SMART Self-test log structure revision number 1

Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error

# 1  Short offline       Completed without error       00%     25452         -

# 2  Short offline       Completed without error       00%     25423         -


SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.
 
Last edited:
M

mruby

Dabbler
Joined
Nov 2, 2015
Messages
29
I could not post them all in one message, it said it was too long, so here are the next few...
 
M

mruby

Dabbler
Joined
Nov 2, 2015
Messages
29
da0
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p28 amd64] (local build)

Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org


=== START OF INFORMATION SECTION ===

Model Family:     Hitachi Deskstar 7K3000

Device Model:     Hitachi HDS723020BLA642

Serial Number:    MN1220F3157D6D

LU WWN Device Id: 5 000cca 369d0791d

Firmware Version: MN6OA580

User Capacity:    2,000,398,934,016 bytes [2.00 TB]

Sector Size:      512 bytes logical/physical

Rotation Rate:    7200 rpm

Form Factor:      3.5 inches

Device is:        In smartctl database [for details use: -P show]

ATA Version is:   ATA8-ACS T13/1699-D revision 4

SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)

Local Time is:    Fri Dec 11 10:45:50 2015 PST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled


=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED


General SMART Values:

Offline data collection status:  (0x84)Offline data collection activity

was suspended by an interrupting command from host.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (   0)The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (19808) seconds.

Offline data collection

capabilities:  (0x5b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003)Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01)Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time:  (   1) minutes.

Extended self-test routine

recommended polling time:  ( 330) minutes.

SCT capabilities:        (0x003d)SCT Status supported.

SCT Error Recovery Control supported.

SCT Feature Control supported.

SCT Data Table supported.


SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always       -       0

  2 Throughput_Performance  0x0005   135   135   054    Pre-fail  Offline      -       84

  3 Spin_Up_Time            0x0007   133   133   024    Pre-fail  Always       -       431 (Average 430)

  4 Start_Stop_Count        0x0012   099   099   000    Old_age   Always       -       5234

  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0

  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0

  8 Seek_Time_Performance   0x0005   133   133   020    Pre-fail  Offline      -       27

  9 Power_On_Hours          0x0012   097   097   000    Old_age   Always       -       25464

10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0

12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       108

192 Power-Off_Retract_Count 0x0032   088   088   000    Old_age   Always       -       14448

193 Load_Cycle_Count        0x0012   088   088   000    Old_age   Always       -       14448

194 Temperature_Celsius     0x0002   253   253   000    Old_age   Always       -       22 (Min/Max 12/62)

196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0

197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0

198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0

199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0


SMART Error Log Version: 1

ATA Error Count: 61 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.


Error 61 occurred at disk power-on lifetime: 25409 hours (1058 days + 17 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 71 87 27 4a 04  Error: UNC at LBA = 0x044a2787 = 71968647


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 70 88 27 4a 44 ff   4d+03:03:12.404  READ FPDMA QUEUED

  60 00 48 f8 28 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 40 f8 27 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 38 f8 26 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 30 f8 25 4a 40 00   4d+03:03:12.401  READ FPDMA QUEUED


Error 60 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 a1 0f 5e ab 0d  Error: UNC at LBA = 0x0dab5e0f = 229334543


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 a0 10 5e ab 4d ff   4d+01:33:08.442  READ FPDMA QUEUED

  60 00 e8 b0 5e ab 40 00   4d+01:33:08.441  READ FPDMA QUEUED

  60 00 e0 b0 5d ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d8 b0 5c ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d0 b0 5b ab 40 00   4d+01:33:08.439  READ FPDMA QUEUED


Error 59 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 b1 c7 94 aa 0d  Error: UNC at LBA = 0x0daa94c7 = 229283015


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 b0 c8 94 aa 4d ff   4d+01:30:07.650  READ FPDMA QUEUED

  60 00 28 78 96 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 20 78 95 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 18 78 94 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 10 78 93 aa 40 00   4d+01:30:07.647  READ FPDMA QUEUED


Error 58 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 c1 07 c9 a9 0d  Error: UNC at LBA = 0x0da9c907 = 229230855


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 c0 08 c9 a9 4d ff   4d+01:26:28.842  READ FPDMA QUEUED

  60 00 68 c8 ca a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 60 c8 c9 a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 58 c8 c8 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED

  60 00 50 c8 c7 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED


Error 57 occurred at disk power-on lifetime: 25406 hours (1058 days + 14 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 31 17 c0 cb 05  Error: UNC at LBA = 0x05cbc017 = 97239063


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 30 18 c0 cb 45 ff   4d+00:26:08.686  READ FPDMA QUEUED

  60 00 08 48 c1 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 00 48 c0 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 f8 48 bf cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED

  60 00 f0 48 be cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED


SMART Self-test log structure revision number 1

Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error

# 1  Short offline       Completed without error       00%     25452         -

# 2  Short offline       Completed without error       00%     25423         -


SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.


da1
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p28 amd64] (local build)

Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org


=== START OF INFORMATION SECTION ===

Model Family:     Hitachi Deskstar 7K3000

Device Model:     Hitachi HDS723020BLA642

Serial Number:    MN1220F3157D6D

LU WWN Device Id: 5 000cca 369d0791d

Firmware Version: MN6OA580

User Capacity:    2,000,398,934,016 bytes [2.00 TB]

Sector Size:      512 bytes logical/physical

Rotation Rate:    7200 rpm

Form Factor:      3.5 inches

Device is:        In smartctl database [for details use: -P show]

ATA Version is:   ATA8-ACS T13/1699-D revision 4

SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)

Local Time is:    Fri Dec 11 10:45:44 2015 PST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled


=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED


General SMART Values:

Offline data collection status:  (0x84)Offline data collection activity

was suspended by an interrupting command from host.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (   0)The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (19808) seconds.

Offline data collection

capabilities:  (0x5b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003)Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01)Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time:  (   1) minutes.

Extended self-test routine

recommended polling time:  ( 330) minutes.

SCT capabilities:        (0x003d)SCT Status supported.

SCT Error Recovery Control supported.

SCT Feature Control supported.

SCT Data Table supported.


SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always       -       0

  2 Throughput_Performance  0x0005   135   135   054    Pre-fail  Offline      -       84

  3 Spin_Up_Time            0x0007   133   133   024    Pre-fail  Always       -       431 (Average 430)

  4 Start_Stop_Count        0x0012   099   099   000    Old_age   Always       -       5234

  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0

  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0

  8 Seek_Time_Performance   0x0005   133   133   020    Pre-fail  Offline      -       27

  9 Power_On_Hours          0x0012   097   097   000    Old_age   Always       -       25464

10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0

12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       108

192 Power-Off_Retract_Count 0x0032   088   088   000    Old_age   Always       -       14448

193 Load_Cycle_Count        0x0012   088   088   000    Old_age   Always       -       14448

194 Temperature_Celsius     0x0002   253   253   000    Old_age   Always       -       22 (Min/Max 12/62)

196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0

197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0

198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0

199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0


SMART Error Log Version: 1

ATA Error Count: 61 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.


Error 61 occurred at disk power-on lifetime: 25409 hours (1058 days + 17 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 71 87 27 4a 04  Error: UNC at LBA = 0x044a2787 = 71968647


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 70 88 27 4a 44 ff   4d+03:03:12.404  READ FPDMA QUEUED

  60 00 48 f8 28 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 40 f8 27 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 38 f8 26 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 30 f8 25 4a 40 00   4d+03:03:12.401  READ FPDMA QUEUED


Error 60 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 a1 0f 5e ab 0d  Error: UNC at LBA = 0x0dab5e0f = 229334543


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 a0 10 5e ab 4d ff   4d+01:33:08.442  READ FPDMA QUEUED

  60 00 e8 b0 5e ab 40 00   4d+01:33:08.441  READ FPDMA QUEUED

  60 00 e0 b0 5d ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d8 b0 5c ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d0 b0 5b ab 40 00   4d+01:33:08.439  READ FPDMA QUEUED


Error 59 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 b1 c7 94 aa 0d  Error: UNC at LBA = 0x0daa94c7 = 229283015


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 b0 c8 94 aa 4d ff   4d+01:30:07.650  READ FPDMA QUEUED

  60 00 28 78 96 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 20 78 95 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 18 78 94 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 10 78 93 aa 40 00   4d+01:30:07.647  READ FPDMA QUEUED


Error 58 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 c1 07 c9 a9 0d  Error: UNC at LBA = 0x0da9c907 = 229230855


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 c0 08 c9 a9 4d ff   4d+01:26:28.842  READ FPDMA QUEUED

  60 00 68 c8 ca a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 60 c8 c9 a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 58 c8 c8 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED

  60 00 50 c8 c7 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED


Error 57 occurred at disk power-on lifetime: 25406 hours (1058 days + 14 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 31 17 c0 cb 05  Error: UNC at LBA = 0x05cbc017 = 97239063


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 30 18 c0 cb 45 ff   4d+00:26:08.686  READ FPDMA QUEUED

  60 00 08 48 c1 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 00 48 c0 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 f8 48 bf cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED

  60 00 f0 48 be cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED


SMART Self-test log structure revision number 1

Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error

# 1  Short offline       Completed without error       00%     25452         -

# 2  Short offline       Completed without error       00%     25423         -


SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.


da3
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p28 amd64] (local build)

Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org


=== START OF INFORMATION SECTION ===

Model Family:     Hitachi Deskstar 7K3000

Device Model:     Hitachi HDS723020BLA642

Serial Number:    MN1220F3157D6D

LU WWN Device Id: 5 000cca 369d0791d

Firmware Version: MN6OA580

User Capacity:    2,000,398,934,016 bytes [2.00 TB]

Sector Size:      512 bytes logical/physical

Rotation Rate:    7200 rpm

Form Factor:      3.5 inches

Device is:        In smartctl database [for details use: -P show]

ATA Version is:   ATA8-ACS T13/1699-D revision 4

SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)

Local Time is:    Fri Dec 11 10:45:03 2015 PST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled


=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED


General SMART Values:

Offline data collection status:  (0x84)Offline data collection activity

was suspended by an interrupting command from host.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (   0)The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (19808) seconds.

Offline data collection

capabilities:  (0x5b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003)Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01)Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time:  (   1) minutes.

Extended self-test routine

recommended polling time:  ( 330) minutes.

SCT capabilities:        (0x003d)SCT Status supported.

SCT Error Recovery Control supported.

SCT Feature Control supported.

SCT Data Table supported.


SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always       -       0

  2 Throughput_Performance  0x0005   135   135   054    Pre-fail  Offline      -       84

  3 Spin_Up_Time            0x0007   133   133   024    Pre-fail  Always       -       431 (Average 430)

  4 Start_Stop_Count        0x0012   099   099   000    Old_age   Always       -       5234

  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0

  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0

  8 Seek_Time_Performance   0x0005   133   133   020    Pre-fail  Offline      -       27

  9 Power_On_Hours          0x0012   097   097   000    Old_age   Always       -       25464

10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0

12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       108

192 Power-Off_Retract_Count 0x0032   088   088   000    Old_age   Always       -       14448

193 Load_Cycle_Count        0x0012   088   088   000    Old_age   Always       -       14448

194 Temperature_Celsius     0x0002   253   253   000    Old_age   Always       -       22 (Min/Max 12/62)

196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0

197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0

198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0

199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0


SMART Error Log Version: 1

ATA Error Count: 61 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.


Error 61 occurred at disk power-on lifetime: 25409 hours (1058 days + 17 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 71 87 27 4a 04  Error: UNC at LBA = 0x044a2787 = 71968647


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 70 88 27 4a 44 ff   4d+03:03:12.404  READ FPDMA QUEUED

  60 00 48 f8 28 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 40 f8 27 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 38 f8 26 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 30 f8 25 4a 40 00   4d+03:03:12.401  READ FPDMA QUEUED


Error 60 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 a1 0f 5e ab 0d  Error: UNC at LBA = 0x0dab5e0f = 229334543


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 a0 10 5e ab 4d ff   4d+01:33:08.442  READ FPDMA QUEUED

  60 00 e8 b0 5e ab 40 00   4d+01:33:08.441  READ FPDMA QUEUED

  60 00 e0 b0 5d ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d8 b0 5c ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d0 b0 5b ab 40 00   4d+01:33:08.439  READ FPDMA QUEUED


Error 59 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 b1 c7 94 aa 0d  Error: UNC at LBA = 0x0daa94c7 = 229283015


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 b0 c8 94 aa 4d ff   4d+01:30:07.650  READ FPDMA QUEUED

  60 00 28 78 96 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 20 78 95 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 18 78 94 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 10 78 93 aa 40 00   4d+01:30:07.647  READ FPDMA QUEUED


Error 58 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 c1 07 c9 a9 0d  Error: UNC at LBA = 0x0da9c907 = 229230855


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 c0 08 c9 a9 4d ff   4d+01:26:28.842  READ FPDMA QUEUED

  60 00 68 c8 ca a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 60 c8 c9 a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 58 c8 c8 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED

  60 00 50 c8 c7 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED


Error 57 occurred at disk power-on lifetime: 25406 hours (1058 days + 14 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 31 17 c0 cb 05  Error: UNC at LBA = 0x05cbc017 = 97239063


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 30 18 c0 cb 45 ff   4d+00:26:08.686  READ FPDMA QUEUED

  60 00 08 48 c1 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 00 48 c0 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 f8 48 bf cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED

  60 00 f0 48 be cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED


SMART Self-test log structure revision number 1

Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error

# 1  Short offline       Completed without error       00%     25452         -

# 2  Short offline       Completed without error       00%     25423         -


SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.
 
Last edited:
M

mruby

Dabbler
Joined
Nov 2, 2015
Messages
29
da4
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p28 amd64] (local build)

Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org


=== START OF INFORMATION SECTION ===

Model Family:     Hitachi Deskstar 7K3000

Device Model:     Hitachi HDS723020BLA642

Serial Number:    MN1220F3157D6D

LU WWN Device Id: 5 000cca 369d0791d

Firmware Version: MN6OA580

User Capacity:    2,000,398,934,016 bytes [2.00 TB]

Sector Size:      512 bytes logical/physical

Rotation Rate:    7200 rpm

Form Factor:      3.5 inches

Device is:        In smartctl database [for details use: -P show]

ATA Version is:   ATA8-ACS T13/1699-D revision 4

SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)

Local Time is:    Fri Dec 11 10:45:27 2015 PST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled


=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED


General SMART Values:

Offline data collection status:  (0x84)Offline data collection activity

was suspended by an interrupting command from host.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (   0)The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (19808) seconds.

Offline data collection

capabilities:  (0x5b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003)Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01)Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time:  (   1) minutes.

Extended self-test routine

recommended polling time:  ( 330) minutes.

SCT capabilities:        (0x003d)SCT Status supported.

SCT Error Recovery Control supported.

SCT Feature Control supported.

SCT Data Table supported.


SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always       -       0

  2 Throughput_Performance  0x0005   135   135   054    Pre-fail  Offline      -       84

  3 Spin_Up_Time            0x0007   133   133   024    Pre-fail  Always       -       431 (Average 430)

  4 Start_Stop_Count        0x0012   099   099   000    Old_age   Always       -       5234

  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0

  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0

  8 Seek_Time_Performance   0x0005   133   133   020    Pre-fail  Offline      -       27

  9 Power_On_Hours          0x0012   097   097   000    Old_age   Always       -       25464

10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0

12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       108

192 Power-Off_Retract_Count 0x0032   088   088   000    Old_age   Always       -       14448

193 Load_Cycle_Count        0x0012   088   088   000    Old_age   Always       -       14448

194 Temperature_Celsius     0x0002   253   253   000    Old_age   Always       -       22 (Min/Max 12/62)

196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0

197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0

198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0

199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0


SMART Error Log Version: 1

ATA Error Count: 61 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.


Error 61 occurred at disk power-on lifetime: 25409 hours (1058 days + 17 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 71 87 27 4a 04  Error: UNC at LBA = 0x044a2787 = 71968647


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 70 88 27 4a 44 ff   4d+03:03:12.404  READ FPDMA QUEUED

  60 00 48 f8 28 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 40 f8 27 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 38 f8 26 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 30 f8 25 4a 40 00   4d+03:03:12.401  READ FPDMA QUEUED


Error 60 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 a1 0f 5e ab 0d  Error: UNC at LBA = 0x0dab5e0f = 229334543


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 a0 10 5e ab 4d ff   4d+01:33:08.442  READ FPDMA QUEUED

  60 00 e8 b0 5e ab 40 00   4d+01:33:08.441  READ FPDMA QUEUED

  60 00 e0 b0 5d ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d8 b0 5c ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d0 b0 5b ab 40 00   4d+01:33:08.439  READ FPDMA QUEUED


Error 59 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 b1 c7 94 aa 0d  Error: UNC at LBA = 0x0daa94c7 = 229283015


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 b0 c8 94 aa 4d ff   4d+01:30:07.650  READ FPDMA QUEUED

  60 00 28 78 96 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 20 78 95 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 18 78 94 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 10 78 93 aa 40 00   4d+01:30:07.647  READ FPDMA QUEUED


Error 58 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 c1 07 c9 a9 0d  Error: UNC at LBA = 0x0da9c907 = 229230855


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 c0 08 c9 a9 4d ff   4d+01:26:28.842  READ FPDMA QUEUED

  60 00 68 c8 ca a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 60 c8 c9 a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 58 c8 c8 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED

  60 00 50 c8 c7 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED


Error 57 occurred at disk power-on lifetime: 25406 hours (1058 days + 14 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 31 17 c0 cb 05  Error: UNC at LBA = 0x05cbc017 = 97239063


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 30 18 c0 cb 45 ff   4d+00:26:08.686  READ FPDMA QUEUED

  60 00 08 48 c1 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 00 48 c0 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 f8 48 bf cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED

  60 00 f0 48 be cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED


SMART Self-test log structure revision number 1

Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error

# 1  Short offline       Completed without error       00%     25452         -

# 2  Short offline       Completed without error       00%     25423         -


SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.


da5
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p28 amd64] (local build)

Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org


=== START OF INFORMATION SECTION ===

Model Family:     Hitachi Deskstar 7K3000

Device Model:     Hitachi HDS723020BLA642

Serial Number:    MN1220F3157D6D

LU WWN Device Id: 5 000cca 369d0791d

Firmware Version: MN6OA580

User Capacity:    2,000,398,934,016 bytes [2.00 TB]

Sector Size:      512 bytes logical/physical

Rotation Rate:    7200 rpm

Form Factor:      3.5 inches

Device is:        In smartctl database [for details use: -P show]

ATA Version is:   ATA8-ACS T13/1699-D revision 4

SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)

Local Time is:    Fri Dec 11 10:45:21 2015 PST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled


=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED


General SMART Values:

Offline data collection status:  (0x84)Offline data collection activity

was suspended by an interrupting command from host.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (   0)The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (19808) seconds.

Offline data collection

capabilities:  (0x5b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003)Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01)Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time:  (   1) minutes.

Extended self-test routine

recommended polling time:  ( 330) minutes.

SCT capabilities:        (0x003d)SCT Status supported.

SCT Error Recovery Control supported.

SCT Feature Control supported.

SCT Data Table supported.


SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always       -       0

  2 Throughput_Performance  0x0005   135   135   054    Pre-fail  Offline      -       84

  3 Spin_Up_Time            0x0007   133   133   024    Pre-fail  Always       -       431 (Average 430)

  4 Start_Stop_Count        0x0012   099   099   000    Old_age   Always       -       5234

  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0

  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0

  8 Seek_Time_Performance   0x0005   133   133   020    Pre-fail  Offline      -       27

  9 Power_On_Hours          0x0012   097   097   000    Old_age   Always       -       25464

10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0

12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       108

192 Power-Off_Retract_Count 0x0032   088   088   000    Old_age   Always       -       14448

193 Load_Cycle_Count        0x0012   088   088   000    Old_age   Always       -       14448

194 Temperature_Celsius     0x0002   253   253   000    Old_age   Always       -       22 (Min/Max 12/62)

196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0

197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0

198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0

199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0


SMART Error Log Version: 1

ATA Error Count: 61 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.


Error 61 occurred at disk power-on lifetime: 25409 hours (1058 days + 17 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 71 87 27 4a 04  Error: UNC at LBA = 0x044a2787 = 71968647


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 70 88 27 4a 44 ff   4d+03:03:12.404  READ FPDMA QUEUED

  60 00 48 f8 28 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 40 f8 27 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 38 f8 26 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 30 f8 25 4a 40 00   4d+03:03:12.401  READ FPDMA QUEUED


Error 60 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 a1 0f 5e ab 0d  Error: UNC at LBA = 0x0dab5e0f = 229334543


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 a0 10 5e ab 4d ff   4d+01:33:08.442  READ FPDMA QUEUED

  60 00 e8 b0 5e ab 40 00   4d+01:33:08.441  READ FPDMA QUEUED

  60 00 e0 b0 5d ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d8 b0 5c ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d0 b0 5b ab 40 00   4d+01:33:08.439  READ FPDMA QUEUED


Error 59 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 b1 c7 94 aa 0d  Error: UNC at LBA = 0x0daa94c7 = 229283015


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 b0 c8 94 aa 4d ff   4d+01:30:07.650  READ FPDMA QUEUED

  60 00 28 78 96 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 20 78 95 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 18 78 94 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 10 78 93 aa 40 00   4d+01:30:07.647  READ FPDMA QUEUED


Error 58 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 c1 07 c9 a9 0d  Error: UNC at LBA = 0x0da9c907 = 229230855


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 c0 08 c9 a9 4d ff   4d+01:26:28.842  READ FPDMA QUEUED

  60 00 68 c8 ca a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 60 c8 c9 a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 58 c8 c8 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED

  60 00 50 c8 c7 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED


Error 57 occurred at disk power-on lifetime: 25406 hours (1058 days + 14 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 31 17 c0 cb 05  Error: UNC at LBA = 0x05cbc017 = 97239063


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 30 18 c0 cb 45 ff   4d+00:26:08.686  READ FPDMA QUEUED

  60 00 08 48 c1 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 00 48 c0 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 f8 48 bf cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED

  60 00 f0 48 be cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED


SMART Self-test log structure revision number 1

Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error

# 1  Short offline       Completed without error       00%     25452         -

# 2  Short offline       Completed without error       00%     25423         -


SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.
 
Last edited:
M

mruby

Dabbler
Joined
Nov 2, 2015
Messages
29
da6
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p28 amd64] (local build)

Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org


=== START OF INFORMATION SECTION ===

Model Family:     Hitachi Deskstar 7K3000

Device Model:     Hitachi HDS723020BLA642

Serial Number:    MN1220F3157D6D

LU WWN Device Id: 5 000cca 369d0791d

Firmware Version: MN6OA580

User Capacity:    2,000,398,934,016 bytes [2.00 TB]

Sector Size:      512 bytes logical/physical

Rotation Rate:    7200 rpm

Form Factor:      3.5 inches

Device is:        In smartctl database [for details use: -P show]

ATA Version is:   ATA8-ACS T13/1699-D revision 4

SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)

Local Time is:    Fri Dec 11 10:45:32 2015 PST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled


=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED


General SMART Values:

Offline data collection status:  (0x84)Offline data collection activity

was suspended by an interrupting command from host.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (   0)The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (19808) seconds.

Offline data collection

capabilities:  (0x5b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003)Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01)Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time:  (   1) minutes.

Extended self-test routine

recommended polling time:  ( 330) minutes.

SCT capabilities:        (0x003d)SCT Status supported.

SCT Error Recovery Control supported.

SCT Feature Control supported.

SCT Data Table supported.


SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always       -       0

  2 Throughput_Performance  0x0005   135   135   054    Pre-fail  Offline      -       84

  3 Spin_Up_Time            0x0007   133   133   024    Pre-fail  Always       -       431 (Average 430)

  4 Start_Stop_Count        0x0012   099   099   000    Old_age   Always       -       5234

  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0

  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0

  8 Seek_Time_Performance   0x0005   133   133   020    Pre-fail  Offline      -       27

  9 Power_On_Hours          0x0012   097   097   000    Old_age   Always       -       25464

10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0

12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       108

192 Power-Off_Retract_Count 0x0032   088   088   000    Old_age   Always       -       14448

193 Load_Cycle_Count        0x0012   088   088   000    Old_age   Always       -       14448

194 Temperature_Celsius     0x0002   253   253   000    Old_age   Always       -       22 (Min/Max 12/62)

196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0

197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0

198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0

199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0


SMART Error Log Version: 1

ATA Error Count: 61 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.


Error 61 occurred at disk power-on lifetime: 25409 hours (1058 days + 17 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 71 87 27 4a 04  Error: UNC at LBA = 0x044a2787 = 71968647


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 70 88 27 4a 44 ff   4d+03:03:12.404  READ FPDMA QUEUED

  60 00 48 f8 28 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 40 f8 27 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 38 f8 26 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 30 f8 25 4a 40 00   4d+03:03:12.401  READ FPDMA QUEUED


Error 60 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 a1 0f 5e ab 0d  Error: UNC at LBA = 0x0dab5e0f = 229334543


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 a0 10 5e ab 4d ff   4d+01:33:08.442  READ FPDMA QUEUED

  60 00 e8 b0 5e ab 40 00   4d+01:33:08.441  READ FPDMA QUEUED

  60 00 e0 b0 5d ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d8 b0 5c ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d0 b0 5b ab 40 00   4d+01:33:08.439  READ FPDMA QUEUED


Error 59 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 b1 c7 94 aa 0d  Error: UNC at LBA = 0x0daa94c7 = 229283015


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 b0 c8 94 aa 4d ff   4d+01:30:07.650  READ FPDMA QUEUED

  60 00 28 78 96 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 20 78 95 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 18 78 94 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 10 78 93 aa 40 00   4d+01:30:07.647  READ FPDMA QUEUED


Error 58 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 c1 07 c9 a9 0d  Error: UNC at LBA = 0x0da9c907 = 229230855


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 c0 08 c9 a9 4d ff   4d+01:26:28.842  READ FPDMA QUEUED

  60 00 68 c8 ca a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 60 c8 c9 a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 58 c8 c8 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED

  60 00 50 c8 c7 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED


Error 57 occurred at disk power-on lifetime: 25406 hours (1058 days + 14 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 31 17 c0 cb 05  Error: UNC at LBA = 0x05cbc017 = 97239063


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 30 18 c0 cb 45 ff   4d+00:26:08.686  READ FPDMA QUEUED

  60 00 08 48 c1 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 00 48 c0 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 f8 48 bf cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED

  60 00 f0 48 be cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED


SMART Self-test log structure revision number 1

Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error

# 1  Short offline       Completed without error       00%     25452         -

# 2  Short offline       Completed without error       00%     25423         -


SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.


da7
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p28 amd64] (local build)

Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org


=== START OF INFORMATION SECTION ===

Model Family:     Hitachi Deskstar 7K3000

Device Model:     Hitachi HDS723020BLA642

Serial Number:    MN1220F3157D6D

LU WWN Device Id: 5 000cca 369d0791d

Firmware Version: MN6OA580

User Capacity:    2,000,398,934,016 bytes [2.00 TB]

Sector Size:      512 bytes logical/physical

Rotation Rate:    7200 rpm

Form Factor:      3.5 inches

Device is:        In smartctl database [for details use: -P show]

ATA Version is:   ATA8-ACS T13/1699-D revision 4

SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)

Local Time is:    Fri Dec 11 10:45:54 2015 PST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled


=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED


General SMART Values:

Offline data collection status:  (0x84)Offline data collection activity

was suspended by an interrupting command from host.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (   0)The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (19808) seconds.

Offline data collection

capabilities:  (0x5b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003)Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01)Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time:  (   1) minutes.

Extended self-test routine

recommended polling time:  ( 330) minutes.

SCT capabilities:        (0x003d)SCT Status supported.

SCT Error Recovery Control supported.

SCT Feature Control supported.

SCT Data Table supported.


SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always       -       0

  2 Throughput_Performance  0x0005   135   135   054    Pre-fail  Offline      -       84

  3 Spin_Up_Time            0x0007   133   133   024    Pre-fail  Always       -       431 (Average 430)

  4 Start_Stop_Count        0x0012   099   099   000    Old_age   Always       -       5234

  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0

  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0

  8 Seek_Time_Performance   0x0005   133   133   020    Pre-fail  Offline      -       27

  9 Power_On_Hours          0x0012   097   097   000    Old_age   Always       -       25464

10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0

12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       108

192 Power-Off_Retract_Count 0x0032   088   088   000    Old_age   Always       -       14448

193 Load_Cycle_Count        0x0012   088   088   000    Old_age   Always       -       14448

194 Temperature_Celsius     0x0002   253   253   000    Old_age   Always       -       22 (Min/Max 12/62)

196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0

197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0

198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0

199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0


SMART Error Log Version: 1

ATA Error Count: 61 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.


Error 61 occurred at disk power-on lifetime: 25409 hours (1058 days + 17 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 71 87 27 4a 04  Error: UNC at LBA = 0x044a2787 = 71968647


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 70 88 27 4a 44 ff   4d+03:03:12.404  READ FPDMA QUEUED

  60 00 48 f8 28 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 40 f8 27 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 38 f8 26 4a 40 00   4d+03:03:12.403  READ FPDMA QUEUED

  60 00 30 f8 25 4a 40 00   4d+03:03:12.401  READ FPDMA QUEUED


Error 60 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 a1 0f 5e ab 0d  Error: UNC at LBA = 0x0dab5e0f = 229334543


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 a0 10 5e ab 4d ff   4d+01:33:08.442  READ FPDMA QUEUED

  60 00 e8 b0 5e ab 40 00   4d+01:33:08.441  READ FPDMA QUEUED

  60 00 e0 b0 5d ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d8 b0 5c ab 40 00   4d+01:33:08.440  READ FPDMA QUEUED

  60 00 d0 b0 5b ab 40 00   4d+01:33:08.439  READ FPDMA QUEUED


Error 59 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 b1 c7 94 aa 0d  Error: UNC at LBA = 0x0daa94c7 = 229283015


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 b0 c8 94 aa 4d ff   4d+01:30:07.650  READ FPDMA QUEUED

  60 00 28 78 96 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 20 78 95 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 18 78 94 aa 40 00   4d+01:30:07.648  READ FPDMA QUEUED

  60 00 10 78 93 aa 40 00   4d+01:30:07.647  READ FPDMA QUEUED


Error 58 occurred at disk power-on lifetime: 25407 hours (1058 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 c1 07 c9 a9 0d  Error: UNC at LBA = 0x0da9c907 = 229230855


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 c0 08 c9 a9 4d ff   4d+01:26:28.842  READ FPDMA QUEUED

  60 00 68 c8 ca a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 60 c8 c9 a9 40 00   4d+01:26:28.840  READ FPDMA QUEUED

  60 00 58 c8 c8 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED

  60 00 50 c8 c7 a9 40 00   4d+01:26:28.839  READ FPDMA QUEUED


Error 57 occurred at disk power-on lifetime: 25406 hours (1058 days + 14 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 31 17 c0 cb 05  Error: UNC at LBA = 0x05cbc017 = 97239063


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  60 00 30 18 c0 cb 45 ff   4d+00:26:08.686  READ FPDMA QUEUED

  60 00 08 48 c1 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 00 48 c0 cb 40 00   4d+00:26:08.684  READ FPDMA QUEUED

  60 00 f8 48 bf cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED

  60 00 f0 48 be cb 40 00   4d+00:26:08.683  READ FPDMA QUEUED


SMART Self-test log structure revision number 1

Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error

# 1  Short offline       Completed without error       00%     25452         -

# 2  Short offline       Completed without error       00%     25423         -


SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.
 
Last edited:
Ericloewe

Ericloewe

Server Wrangler
Moderator
Joined
Feb 15, 2014
Messages
20,194
Code:
CODE tags make smartctl readable!

Variable-width fonts and whitespace suppression make console outputs nearly unreadable!
 
M

mruby

Dabbler
Joined
Nov 2, 2015
Messages
29
Changed to code tags.

Thanks
 
Ericloewe

Ericloewe

Server Wrangler
Moderator
Joined
Feb 15, 2014
Messages
20,194
The drives themselves seem ok, suggesting a host-side issue. Cabling is typical, but it seems a bit widespread to be something so simple.

Bad power seems the next likeliest option, since the drives are both on the PCH and the SAS HBA.
 
M

mruby

Dabbler
Joined
Nov 2, 2015
Messages
29
Bad power seems the next likeliest option, since the drives are both on the PCH and the SAS HBA.
Click to expand...

I had read something that indicated power being an issue as well, such as an over worked power supply etc. I have hot swap power supplies. The chassis can hold 4, but i'm only running 2 currently. They are each 350 w, and my server is running around 250 watts on average. Seems like I have enough juice, but its hard for me to test.

Maybe i will pull 6 of my disks (the 6 that are not experiencing any errors), so that it lessens the energy usage, and see if I still get errors.

Sorry for the dumb question, but what do you mean by PCH and SAS HBA?

Thanks!
 
Ericloewe

Ericloewe

Server Wrangler
Moderator
Joined
Feb 15, 2014
Messages
20,194
mruby said:
Sorry for the dumb question, but what do you mean by PCH and SAS HBA?
Click to expand...
PCH is the Platform Controller Hub, what is left of the entity known as the chipset. Those are the motherboard's SATA ports.
The SAS Host Bus Adapter is the M1015. Also, I just noticed you also have an SAS 2308 integrated on the motherboard, which kinda makes your M1015 redundant, in most cases - either one of them will do the job admirably, if everything's working well. The M1015 uses the 2308's predecessor, the SAS 2008.
 
M

mruby

Dabbler
Joined
Nov 2, 2015
Messages
29
Ok, the only reason for my M1015 is for extra ports. I have a 24 bay storage chassis, and only 12 ports i think on the mobo.

Any ideas why the drives on the M1015 wouldn't be throwing errors? Those cables are brand new, the mini sas to sata cables. The sata cables being used for the rest of the drive are like 10 years old. I just cannot imagine them all going bad within a day of each other.
 
Sakuru

Sakuru

Guru
Joined
Nov 20, 2015
Messages
527
You must log in or register to reply here.

Similar threads

titanve
Device: /dev/ciss0 [cciss_disk_00] [SAT] error
2
Replies
22
Views
8K
titanve
titanve
T
  • Locked
Disk errors, Smart report
Replies
1
Views
1K
danb35
danb35
T
I think I bought a bad drive....
Replies
7
Views
3K
TK-24601
T
P
Self-Test Log error count increased
Replies
3
Views
1K
Ebedorian
Ebedorian
O
Disk error, what to do?
2
Replies
36
Views
8K
Apollo
A
Top