Hello,
I have two FreeNAS machines running very similar Supermicro hardware.
Box 1:
FreeNAS-9.2.1.6-RELEASE-x64 (ddd1e39)
System Information
Manufacturer: Supermicro
Product Name: X9SCL/X9SCM
10GbE NIC: Supermicro AOC-STGN-I1S <- single port (Intel® 82599EN 10 Gigabit Ethernet Controller)
Box 2:
FreeNAS-9.2.1.6-RELEASE-x64 (ddd1e39)
System Information
Manufacturer: Supermicro
Product Name: X9DRi-LN4+/X9DR3-LN4+
10GbE NIC: Supermicro AOC-STGN-I2S <- dual port (Intel® 82599ES 10 Gigabit Ethernet Controller)
From initial install, Box 1 saw the 10GbE NIC and loaded it right away:
ix0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 9000
options=407bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,VLAN_HWTSO>
ether 00:25:90:e1:c2:e7
inet 10.12.13.153 netmask 0xffffff00 broadcast 10.12.13.255
nd6 options=9<PERFORMNUD,IFDISABLED>
media: Ethernet autoselect (10Gbase-Twinax <full-duplex>)
status: active
However, Box 2 does not even find the card. I have tried moving it to different slots. Box 1 has 2 onboard NICs and Box 2 has 4 onboard. It finds all 4 onboard but just not the ix0/1 NIC.
I do not find anything about "ix0" or anything else related to the 10GbE NIC in dmesg.
I do not have a clue why this would be happening or what steps to take.
Thank you in advanced.
I have two FreeNAS machines running very similar Supermicro hardware.
Box 1:
FreeNAS-9.2.1.6-RELEASE-x64 (ddd1e39)
System Information
Manufacturer: Supermicro
Product Name: X9SCL/X9SCM
10GbE NIC: Supermicro AOC-STGN-I1S <- single port (Intel® 82599EN 10 Gigabit Ethernet Controller)
Box 2:
FreeNAS-9.2.1.6-RELEASE-x64 (ddd1e39)
System Information
Manufacturer: Supermicro
Product Name: X9DRi-LN4+/X9DR3-LN4+
10GbE NIC: Supermicro AOC-STGN-I2S <- dual port (Intel® 82599ES 10 Gigabit Ethernet Controller)
From initial install, Box 1 saw the 10GbE NIC and loaded it right away:
ix0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 9000
options=407bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,VLAN_HWTSO>
ether 00:25:90:e1:c2:e7
inet 10.12.13.153 netmask 0xffffff00 broadcast 10.12.13.255
nd6 options=9<PERFORMNUD,IFDISABLED>
media: Ethernet autoselect (10Gbase-Twinax <full-duplex>)
status: active
However, Box 2 does not even find the card. I have tried moving it to different slots. Box 1 has 2 onboard NICs and Box 2 has 4 onboard. It finds all 4 onboard but just not the ix0/1 NIC.
I do not find anything about "ix0" or anything else related to the 10GbE NIC in dmesg.
I do not have a clue why this would be happening or what steps to take.
Thank you in advanced.
Last edited: