Hey All,
I haven't found a ton of information related to my problem on the forums, so I'm posting to see if anyone has some ideas to help troubleshoot.
A ~week ago I had a mysterious reboot:
After researching I assumed this meant that one particular drive was about to give up the ghost, so I was preparing to swap in a new drive and the box rebooted again (10/7), this time a different GPTID was cited as the problem. I've now had five reboots with all four disks showing up at least once:
Oct 5 19:03 I/O to pool 'tank' appears to be hung on vdev guid 12989182611123154543 at '/dev/gptid/51b4e5cf-99c7-11e9-a5e3-3860778b006f'.
Oct 7 04:45 I/O to pool 'tank' appears to be hung on vdev guid 15794669731177043768 at '/dev/gptid/62a87797-74e4-11e8-80b0-3860778b006f'.
Oct 10 19:50 I/O to pool 'tank' appears to be hung on vdev guid 8409777197129091168 at '/dev/gptid/d15a6389-8ba8-11e9-b5ab-3860778b006f'.
Oct 13 17:45 I/O to pool 'tank' appears to be hung on vdev guid 15794669731177043768 at '/dev/gptid/62a87797-74e4-11e8-80b0-3860778b006f'
Oct 14 19:16 I/O to pool 'tank' appears to be hung on vdev guid 2622870734464222642 at '/dev/gptid/6e2c1e3d-9251-11e9-b4ef-3860778b006f'.
I've run short and conveyance SMART tests on all of the disks in my pool (4x4tb drives in Z2, pool details below, 16gb of RAM, disk space only about 51% used) with zero errors. However, I have not been able to complete any long SMART tests because the machine has now rebooted every couple days and the test will not complete in that time. No issues with a scrub completed on Sunday night.
smartctl -a /dev/ada0 :
so now, I am not so sure that it is one disk that is the problem. However, also strangely, this part is always the same from the /data/crash/info.x logs:
does this indicate that /dev/ada3 could be a problematic disk?
My main questions:
1. Does any of this seem to indicate that _only_ one disk is failing?
2. Can I do any more investigation to figure out the cause?
3. Is there a possibility that the controller on the main board is failing?
3a. if this is the case, would getting a dedicated controller card be a better solution than a new mainboard (machine is from 2013, I guess I'm trying to ride it until the wheels fall off)
4. Could suddenly bad memory be at fault here? (I am running 16GB of ECC)
5. Why is a kernel panic when a drive starting to fail an acceptable solution? (rhetorical, lol, not very graceful)
I am trying to avoid throwing money at parts. Things have been going swimmingly for many years with this machine.
appendix
===
system specs:
FreeNAS-11.2-U7 (Build Date: Nov 19, 2019 0:4)
Intel(R) Pentium(R) CPU G860 @ 3.00GHz (2 cores)
16 GiB
zpool status
smartctl -a /dev/ada1
smartctl -a /dev/ada2
smartctl -a /dev/ada3
I haven't found a ton of information related to my problem on the forums, so I'm posting to see if anyone has some ideas to help troubleshoot.
A ~week ago I had a mysterious reboot:
I/O to pool 'tank' appears to be hung on vdev guid 12989182611123154543 at '/dev/gptid/51b4e5cf-99c7-11e9-a5e3-3860778b006f'.
After researching I assumed this meant that one particular drive was about to give up the ghost, so I was preparing to swap in a new drive and the box rebooted again (10/7), this time a different GPTID was cited as the problem. I've now had five reboots with all four disks showing up at least once:
Oct 5 19:03 I/O to pool 'tank' appears to be hung on vdev guid 12989182611123154543 at '/dev/gptid/51b4e5cf-99c7-11e9-a5e3-3860778b006f'.
Oct 7 04:45 I/O to pool 'tank' appears to be hung on vdev guid 15794669731177043768 at '/dev/gptid/62a87797-74e4-11e8-80b0-3860778b006f'.
Oct 10 19:50 I/O to pool 'tank' appears to be hung on vdev guid 8409777197129091168 at '/dev/gptid/d15a6389-8ba8-11e9-b5ab-3860778b006f'.
Oct 13 17:45 I/O to pool 'tank' appears to be hung on vdev guid 15794669731177043768 at '/dev/gptid/62a87797-74e4-11e8-80b0-3860778b006f'
Oct 14 19:16 I/O to pool 'tank' appears to be hung on vdev guid 2622870734464222642 at '/dev/gptid/6e2c1e3d-9251-11e9-b4ef-3860778b006f'.
I've run short and conveyance SMART tests on all of the disks in my pool (4x4tb drives in Z2, pool details below, 16gb of RAM, disk space only about 51% used) with zero errors. However, I have not been able to complete any long SMART tests because the machine has now rebooted every couple days and the test will not complete in that time. No issues with a scrub completed on Sunday night.
smartctl -a /dev/ada0 :
Code:
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.2-STABLE amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate BarraCuda 3.5 Device Model: ST4000DM004-2CV104 Serial Number: ZFN16ANN LU WWN Device Id: 5 000c50 0b013b768 Firmware Version: 0001 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5425 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Oct 14 20:21:05 2020 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 249) Self-test routine in progress... 90% of test remaining. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 487) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x30a5) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 076 064 006 Pre-fail Always - 41783703 3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 34 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 095 060 045 Pre-fail Always - 3063684620 9 Power_On_Hours 0x0032 077 077 000 Old_age Always - 20329 (185 104 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 24 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 057 049 040 Old_age Always - 43 (Min/Max 38/49) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 718 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 872 194 Temperature_Celsius 0x0022 043 051 000 Old_age Always - 43 (0 29 0 0 0) 195 Hardware_ECC_Recovered 0x001a 076 064 000 Old_age Always - 41783703 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 191 000 Old_age Always - 23 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 20239h+32m+43.634s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 68382963370 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 90268081333 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Self-test routine in progress 90% 20329 - # 2 Extended offline Interrupted (host reset) 90% 20328 - # 3 Extended offline Interrupted (host reset) 80% 20302 - # 4 Conveyance offline Completed without error 00% 20270 - # 5 Short offline Completed without error 00% 20270 - # 6 Short offline Completed without error 00% 20270 - # 7 Short offline Completed without error 00% 20263 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
so now, I am not so sure that it is one disk that is the problem. However, also strangely, this part is always the same from the /data/crash/info.x logs:
Dump header from device: /dev/ada3p1
does this indicate that /dev/ada3 could be a problematic disk?
My main questions:
1. Does any of this seem to indicate that _only_ one disk is failing?
2. Can I do any more investigation to figure out the cause?
3. Is there a possibility that the controller on the main board is failing?
3a. if this is the case, would getting a dedicated controller card be a better solution than a new mainboard (machine is from 2013, I guess I'm trying to ride it until the wheels fall off)
4. Could suddenly bad memory be at fault here? (I am running 16GB of ECC)
5. Why is a kernel panic when a drive starting to fail an acceptable solution? (rhetorical, lol, not very graceful)
I am trying to avoid throwing money at parts. Things have been going swimmingly for many years with this machine.
appendix
===
system specs:
FreeNAS-11.2-U7 (Build Date: Nov 19, 2019 0:4)
Intel(R) Pentium(R) CPU G860 @ 3.00GHz (2 cores)
16 GiB
zpool status
Code:
pool: tank state: ONLINE status: Some supported features are not enabled on the pool. The pool can still be used, but some features are unavailable. action: Enable all features using 'zpool upgrade'. Once this is done, the pool may no longer be accessible by software that does not support the features. See zpool-features(7) for details. scan: scrub repaired 0 in 0 days 20:07:13 with 0 errors on Sun Oct 11 20:16:56 2020 config: NAME STATE READ WRITE CKSUM tank ONLINE 0 0 0 raidz2-0 ONLINE 0 0 0 gptid/d15a6389-8ba8-11e9-b5ab-3860778b006f ONLINE 0 0 0 gptid/6e2c1e3d-9251-11e9-b4ef-3860778b006f ONLINE 0 0 0 gptid/51b4e5cf-99c7-11e9-a5e3-3860778b006f ONLINE 0 0 0 gptid/62a87797-74e4-11e8-80b0-3860778b006f ONLINE 0 0 0
smartctl -a /dev/ada1
Code:
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.2-STABLE amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate BarraCuda 3.5 Device Model: ST4000DM004-2CV104 Serial Number: ZFN16HLM LU WWN Device Id: 5 000c50 0b013f937 Firmware Version: 0001 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5425 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Oct 14 20:42:30 2020 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 41) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 484) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x30a5) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 076 064 006 Pre-fail Always - 42388043 3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 14 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 092 060 045 Pre-fail Always - 1771659284 9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 11613 (120 16 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 14 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 058 051 040 Old_age Always - 42 (Min/Max 37/49) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 391 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 489 194 Temperature_Celsius 0x0022 042 049 000 Old_age Always - 42 (0 28 0 0 0) 195 Hardware_ECC_Recovered 0x001a 076 064 000 Old_age Always - 42388043 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 11583h+30m+13.306s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 48053204564 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 53244477691 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Interrupted (host reset) 90% 11612 - # 2 Conveyance offline Completed without error 00% 11554 - # 3 Short offline Completed without error 00% 11553 - # 4 Short offline Completed without error 00% 11547 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
smartctl -a /dev/ada2
Code:
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.2-STABLE amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate BarraCuda 3.5 Device Model: ST4000DM004-2CV104 Serial Number: ZFN16GZ3 LU WWN Device Id: 5 000c50 0b0136815 Firmware Version: 0001 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5425 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Wed Oct 14 20:42:35 2020 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 41) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 491) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x30a5) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 076 064 006 Pre-fail Always - 42390765 3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 16 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 092 060 045 Pre-fail Always - 1678812342 9 Power_On_Hours 0x0032 088 088 000 Old_age Always - 11385 (251 39 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 15 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 060 051 040 Old_age Always - 40 (Min/Max 38/49) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 374 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 481 194 Temperature_Celsius 0x0022 040 049 000 Old_age Always - 40 (0 29 0 0 0) 195 Hardware_ECC_Recovered 0x001a 076 064 000 Old_age Always - 42390765 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 11342h+59m+23.113s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 47796040612 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 49730244947 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Interrupted (host reset) 90% 11384 - # 2 Conveyance offline Completed without error 00% 11326 - # 3 Short offline Completed without error 00% 11326 - # 4 Short offline Completed without error 00% 11319 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
smartctl -a /dev/ada3
Code:
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.2-STABLE amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate BarraCuda 3.5 Device Model: ST4000DM004-2CV104 Serial Number: ZFN166VD LU WWN Device Id: 5 000c50 0b01530d0 Firmware Version: 0001 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5425 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Wed Oct 14 20:42:42 2020 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 41) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 487) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x30a5) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 076 064 006 Pre-fail Always - 42839939 3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 17 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 092 060 045 Pre-fail Always - 1713849547 9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 11815 (187 221 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 17 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 099 000 Old_age Always - 0 0 1 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 060 050 040 Old_age Always - 40 (Min/Max 37/48) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 408 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 503 194 Temperature_Celsius 0x0022 040 050 000 Old_age Always - 40 (0 29 0 0 0) 195 Hardware_ECC_Recovered 0x001a 076 064 000 Old_age Always - 42839939 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 11786h+21m+35.577s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 48285408849 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 56770760577 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Interrupted (host reset) 90% 11814 - # 2 Conveyance offline Completed without error 00% 11756 - # 3 Short offline Completed without error 00% 11756 - # 4 Short offline Completed without error 00% 11749 - # 5 Extended offline Interrupted (host reset) 80% 11718 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.