One of my hdds ata error count keeps increasing. Its a new harddrive so I'm hoping its nothing serious. It started at like 200 before now its like 417. Should I be worried? Maybe try to return it?
I did the smartctl -a thing but I don't really understand it.
I did the smartctl -a thing but I don't really understand it.
Code:
smartctl 6.5 2016-05-07 r4318 [FreeBSD 10.3-STABLE amd64] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Ultrastar 7K3000 Device Model: Hitachi HUA723030ALA640 Serial Number: MK0371YVH0N0XA LU WWN Device Id: 5 000cca 234ce62b1 Firmware Version: MKAOAA10 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Mar 28 15:25:45 2017 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 24) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off supp ort. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 468) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_ FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 135 135 054 Pre-fail Offline - 84 3 Spin_Up_Time 0x0007 135 135 024 Pre-fail Always - 519 (Average 622) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 29 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 123 123 020 Pre-fail Offline - 31 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 55 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 29 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 30 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 30 194 Temperature_Celsius 0x0002 117 117 000 Old_age Always - 51 (Min/Max 19/53) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 479 SMART Error Log Version: 1 ATA Error Count: 479 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 479 occurred at disk power-on lifetime: 42 hours (1 days + 18 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 2f f9 57 00 Error: ICRC, ABRT at LBA = 0x0057f92f = 5765423 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 00 2f f9 57 40 ff 08:44:34.817 READ FPDMA QUEUED 60 08 40 28 f9 57 40 00 08:44:34.817 READ FPDMA QUEUED 60 08 38 60 f9 57 40 00 08:44:34.809 READ FPDMA QUEUED 60 08 30 b0 f9 57 40 00 08:44:34.804 READ FPDMA QUEUED 60 08 28 58 f9 57 40 00 08:44:34.791 READ FPDMA QUEUED Error 478 occurred at disk power-on lifetime: 42 hours (1 days + 18 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 1f c1 42 04 Error: ICRC, ABRT at LBA = 0x0442c11f = 71483679 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 00 1f c1 42 44 ff 08:41:31.652 READ FPDMA QUEUED 60 08 10 10 c1 42 40 00 08:41:31.652 READ FPDMA QUEUED 60 08 08 38 c1 42 40 00 08:41:31.652 READ FPDMA QUEUED 60 08 00 c8 c1 42 40 00 08:41:31.652 READ FPDMA QUEUED 60 08 f8 40 c1 42 40 00 08:41:31.652 READ FPDMA QUEUED Error 477 occurred at disk power-on lifetime: 42 hours (1 days + 18 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 1f 9a 5a 00 Error: ICRC, ABRT at LBA = 0x005a9a1f = 5937695 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 00 1f 9a 5a 40 ff 08:41:31.062 READ FPDMA QUEUED 60 08 e0 18 9a 5a 40 00 08:41:31.062 READ FPDMA QUEUED 60 08 d8 f8 9a 5a 40 00 08:41:31.061 READ FPDMA QUEUED 60 08 d0 c0 99 5a 40 00 08:41:31.061 READ FPDMA QUEUED 60 08 c8 d8 9a 5a 40 00 08:41:31.060 READ FPDMA QUEUED Error 476 occurred at disk power-on lifetime: 42 hours (1 days + 18 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 0f 65 5a 00 Error: ICRC, ABRT at LBA = 0x005a650f = 5924111 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 00 0f 65 5a 40 ff 08:41:30.095 READ FPDMA QUEUED 60 08 b0 08 65 5a 40 00 08:41:30.095 READ FPDMA QUEUED 60 08 a8 68 64 5a 40 00 08:41:30.091 READ FPDMA QUEUED 60 08 a0 a8 68 5a 40 00 08:41:30.089 READ FPDMA QUEUED 60 08 98 e8 63 5a 40 00 08:41:30.086 READ FPDMA QUEUED Error 475 occurred at disk power-on lifetime: 42 hours (1 days + 18 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 ef 66 5a 00 Error: ICRC, ABRT at LBA = 0x005a66ef = 5924591 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 00 ef 66 5a 40 ff 08:41:29.878 READ FPDMA QUEUED 60 08 f0 e8 66 5a 40 00 08:41:29.878 READ FPDMA QUEUED 60 08 e8 68 65 5a 40 00 08:41:29.876 READ FPDMA QUEUED 60 08 e0 80 68 5a 40 00 08:41:29.875 READ FPDMA QUEUED 60 08 d8 70 68 5a 40 00 08:41:29.873 READ FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA _of_first_error # 1 Short captive Completed without error 00% 1 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.