Hi
I am also using the same card. These are the details of my card.
Code:
Avago Technologies SAS3 Flash Utility
Version 16.00.00.00 (2017.05.02)
Copyright 2008-2017 Avago Technologies. All rights reserved.
Adapter Selected is a Avago SAS: SAS3224(A1)
Controller Number : 0
Controller : SAS3224(A1)
PCI Address : 00:02:00:00
SAS Address : 500062b-2-0299-1697
NVDATA Version (Default) : 10.00.00.03
NVDATA Version (Persistent) : 10.00.00.03
Firmware Product ID : 0x2228 (IT)
Firmware Version : 16.00.12.00
NVDATA Vendor : LSI
NVDATA Product ID : SAS9305-24i
BIOS Version : 08.37.02.00
UEFI BSD Version : 18.00.03.00
FCODE Version : N/A
Board Name : SAS9305-24i
Board Assembly : 03-25699-02004
Board Tracer Number : XW84190355
Finished Processing Commands Successfully.
Exiting SAS3Flash.
Had some weird issues similar to what you had but only with one drive.
Code:
Sep 13 18:23:23 S-STORE01 mpr0: Controller reported scsi ioc terminated tgt 11 SMID 1249 loginfo 31110d01
Sep 13 18:23:23 S-STORE01 (da11:mpr0:0:11:0): WRITE(10). CDB: 2a 00 07 59 8f 20 00 08 00 00
Sep 13 18:23:23 S-STORE01 (da11:mpr0:0:11:0): CAM status: CCB request completed with an error
Sep 13 18:23:23 S-STORE01 (da11:mpr0:0:11:0): Retrying command, 3 more tries remain
Sep 13 18:23:24 S-STORE01 (da11:mpr0:0:11:0): WRITE(10). CDB: 2a 00 07 59 8f 20 00 08 00 00
Sep 13 18:23:24 S-STORE01 (da11:mpr0:0:11:0): CAM status: SCSI Status Error
Sep 13 18:23:24 S-STORE01 (da11:mpr0:0:11:0): SCSI status: Check Condition
Sep 13 18:23:24 S-STORE01 (da11:mpr0:0:11:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
Sep 13 18:23:24 S-STORE01 (da11:mpr0:0:11:0): Retrying command (per sense data)
Sep 13 18:26:03 S-STORE01 mpr0: Controller reported scsi ioc terminated tgt 11 SMID 298 loginfo 31110d01
Sep 13 18:26:03 S-STORE01 (da11:mpr0:0:11:0): WRITE(10). CDB: 2a 00 0a 00 19 a0 00 08 00 00
Sep 13 18:26:03 S-STORE01 (da11:mpr0:0:11:0): CAM status: CCB request completed with an error
Sep 13 18:26:03 S-STORE01 (da11:mpr0:0:11:0): Retrying command, 3 more tries remain
Sep 13 18:26:04 S-STORE01 (da11:mpr0:0:11:0): WRITE(10). CDB: 2a 00 0a 00 19 a0 00 08 00 00
Sep 13 18:26:04 S-STORE01 (da11:mpr0:0:11:0): CAM status: SCSI Status Error
Sep 13 18:26:04 S-STORE01 (da11:mpr0:0:11:0): SCSI status: Check Condition
Sep 13 18:26:04 S-STORE01 (da11:mpr0:0:11:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
They went away after changing the cable but today I was adding some more drives to the remaining slots I had an it came back again.
Code:
Oct 8 14:24:35 S-STORE01 mpr0: Found device <881<SataDev,Direct>,End Device> <6.0Gbps> handle<0x002b> enclosureHandle<0x0001> slot 16
Oct 8 14:24:35 S-STORE01 mpr0: At enclosure level 0 and connector name ( )
Oct 8 14:24:35 S-STORE01 da16 at mpr0 bus 0 scbus0 target 16 lun 0
Oct 8 14:24:35 S-STORE01 da16: <ATA ST14000NE0008-2J EN01> Fixed Direct Access SPC-4 SCSI device
Oct 8 14:24:35 S-STORE01 da16: Serial Number ZHZ3HZ36
Oct 8 14:24:35 S-STORE01 da16: 600.000MB/s transfers
Oct 8 14:24:35 S-STORE01 da16: Command Queueing enabled
Oct 8 14:24:35 S-STORE01 da16: 13351936MB (27344764928 512 byte sectors)
Oct 8 14:24:35 S-STORE01 mpr0: Found device <881<SataDev,Direct>,End Device> <6.0Gbps> handle<0x002c> enclosureHandle<0x0001> slot 17
Oct 8 14:24:35 S-STORE01 mpr0: At enclosure level 0 and connector name ( )
Oct 8 14:24:35 S-STORE01 da17 at mpr0 bus 0 scbus0 target 17 lun 0
Oct 8 14:24:35 S-STORE01 da17: <ATA ST14000NE0008-2J EN01> Fixed Direct Access SPC-4 SCSI device
Oct 8 14:24:35 S-STORE01 da17: Serial Number ZHZ5XBP8
Oct 8 14:24:35 S-STORE01 da17: 600.000MB/s transfers
Oct 8 14:24:35 S-STORE01 da17: Command Queueing enabled
Oct 8 14:24:35 S-STORE01 da17: 13351936MB (27344764928 512 byte sectors)
Oct 8 14:24:35 S-STORE01 mpr0: Found device <881<SataDev,Direct>,End Device> <6.0Gbps> handle<0x002d> enclosureHandle<0x0001> slot 18
Oct 8 14:24:35 S-STORE01 mpr0: At enclosure level 0 and connector name ( )
Oct 8 14:24:35 S-STORE01 da18 at mpr0 bus 0 scbus0 target 18 lun 0
Oct 8 14:24:35 S-STORE01 da18: <ATA ST14000NE0008-2J EN01> Fixed Direct Access SPC-4 SCSI device
Oct 8 14:24:35 S-STORE01 da18: Serial Number ZHZ4J5YV
Oct 8 14:24:35 S-STORE01 da18: 600.000MB/s transfers
Oct 8 14:24:35 S-STORE01 da18: Command Queueing enabled
Oct 8 14:24:35 S-STORE01 da18: 13351936MB (27344764928 512 byte sectors)
Oct 8 14:24:35 S-STORE01 mpr0: Found device <881<SataDev,Direct>,End Device> <6.0Gbps> handle<0x002e> enclosureHandle<0x0001> slot 19
Oct 8 14:24:35 S-STORE01 mpr0: At enclosure level 0 and connector name ( )
Oct 8 14:24:35 S-STORE01 da19 at mpr0 bus 0 scbus0 target 19 lun 0
Oct 8 14:24:35 S-STORE01 da19: <ATA ST14000NE0008-2J EN01> Fixed Direct Access SPC-4 SCSI device
Oct 8 14:24:35 S-STORE01 da19: Serial Number ZHZ4F49X
Oct 8 14:24:35 S-STORE01 da19: 600.000MB/s transfers
Oct 8 14:24:35 S-STORE01 da19: Command Queueing enabled
Oct 8 14:24:35 S-STORE01 da19: 13351936MB (27344764928 512 byte sectors)
Oct 8 14:24:35 S-STORE01 (da19:mpr0:0:19:0): MODE SENSE(6). CDB: 1a 00 01 00 c0 00 length 192 SMID 689 Command timeout on target 19(0x002e), 60000 set, 60.213524600 elapsed
Oct 8 14:24:35 S-STORE01 mpr0: At enclosure level 0, slot 19, connector name ( )
Oct 8 14:24:35 S-STORE01 mpr0: Sending abort to target 19 for SMID 689
Oct 8 14:24:35 S-STORE01 (da19:mpr0:0:19:0): MODE SENSE(6). CDB: 1a 00 01 00 c0 00 length 192 SMID 689 Aborting command 0xfffffe01a72b63f8
Oct 8 14:24:35 S-STORE01 mpr0: Finished abort recovery for target 19
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): READ(10). CDB: 28 00 00 4c 06 c1 00 00 04 00
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): CAM status: SCSI Status Error
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): SCSI status: Check Condition
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): SCSI sense: ABORTED COMMAND asc:47,0 (SCSI parity error)
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): Retrying command (per sense data)
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): READ(10). CDB: 28 00 00 4c 06 c1 00 00 04 00
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): CAM status: SCSI Status Error
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): SCSI status: Check Condition
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): SCSI sense: ABORTED COMMAND asc:47,0 (SCSI parity error)
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): Retrying command (per sense data)
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): READ(16). CDB: 88 00 00 00 00 06 5d dc df c1 00 00 00 04 00 00
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): CAM status: SCSI Status Error
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): SCSI status: Check Condition
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): SCSI sense: ABORTED COMMAND asc:47,0 (SCSI parity error)
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): Retrying command (per sense data)
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): READ(16). CDB: 88 00 00 00 00 06 5d dc df c1 00 00 00 04 00 00
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): CAM status: SCSI Status Error
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): SCSI status: Check Condition
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): SCSI sense: ABORTED COMMAND asc:47,0 (SCSI parity error)
Oct 8 14:24:36 S-STORE01 (da19:mpr0:0:19:0): Retrying command (per sense data)
Oct 8 14:27:18 S-STORE01 mpr0: mprsas_prepare_remove: Sending reset for target ID 19
Oct 8 14:27:18 S-STORE01 da19 at mpr0 bus 0 scbus0 target 19 lun 0
Oct 8 14:27:18 S-STORE01 da19: <ATA ST14000NE0008-2J EN01> s/n ZHZ4F49X detached
Oct 8 14:27:18 S-STORE01 (da19:mpr0:0:19:0): Periph destroyed
Oct 8 14:27:18 S-STORE01 mpr0: No pending commands: starting remove_device
Oct 8 14:27:18 S-STORE01 mpr0: clearing target 19 handle 0x002e
Oct 8 14:27:18 S-STORE01 mpr0: At enclosure level 0, slot 19, connector name ( )
Oct 8 14:28:50 S-STORE01 mpr0: Found device <881<SataDev,Direct>,End Device> <6.0Gbps> handle<0x002e> enclosureHandle<0x0001> slot 19
Oct 8 14:28:50 S-STORE01 mpr0: At enclosure level 0 and connector name ( )
Oct 8 14:28:50 S-STORE01 da19 at mpr0 bus 0 scbus0 target 19 lun 0
Oct 8 14:28:50 S-STORE01 da19: <ATA ST14000NE0008-2J EN01> Fixed Direct Access SPC-4 SCSI device
Oct 8 14:28:50 S-STORE01 da19: Serial Number ZHZ4F49X
Oct 8 14:28:50 S-STORE01 da19: 600.000MB/s transfers
Oct 8 14:28:50 S-STORE01 da19: Command Queueing enabled
Oct 8 14:28:50 S-STORE01 da19: 13351936MB (27344764928 512 byte sectors)
Oct 8 14:28:50 S-STORE01 (da19:mpr0:0:19:0): MODE SENSE(6). CDB: 1a 00 01 00 c0 00 length 192 SMID 609 Command timeout on target 19(0x002e), 60000 set, 60.32013045 elapsed
Oct 8 14:28:50 S-STORE01 mpr0: At enclosure level 0, slot 19, connector name ( )
Oct 8 14:28:50 S-STORE01 mpr0: Sending abort to target 19 for SMID 609
Oct 8 14:28:50 S-STORE01 (da19:mpr0:0:19:0): MODE SENSE(6). CDB: 1a 00 01 00 c0 00 length 192 SMID 609 Aborting command 0xfffffe01a72aee78
Oct 8 14:28:50 S-STORE01 mpr0: Finished abort recovery for target 19
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): READ(6). CDB: 08 00 00 02 20 00
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): CAM status: SCSI Status Error
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): SCSI status: Check Condition
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): SCSI sense: ABORTED COMMAND asc:47,0 (SCSI parity error)
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): Retrying command (per sense data)
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): READ(16). CDB: 88 00 00 00 00 06 5d df ff df 00 00 00 20 00 00
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): CAM status: SCSI Status Error
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): SCSI status: Check Condition
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): SCSI sense: ABORTED COMMAND asc:47,0 (SCSI parity error)
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): Retrying command (per sense data)
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): READ(16). CDB: 88 00 00 00 00 06 5d df ff df 00 00 00 20 00 00
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): CAM status: SCSI Status Error
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): SCSI status: Check Condition
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): SCSI sense: ABORTED COMMAND asc:47,0 (SCSI parity error)
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): Retrying command (per sense data)
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): READ(10). CDB: 28 00 00 4c 06 c1 00 00 04 00
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): CAM status: SCSI Status Error
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): SCSI status: Check Condition
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): SCSI sense: ABORTED COMMAND asc:47,0 (SCSI parity error)
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): Retrying command (per sense data)
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): READ(10). CDB: 28 00 00 4c 06 c1 00 00 04 00
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): CAM status: SCSI Status Error
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): SCSI status: Check Condition
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): SCSI sense: ABORTED COMMAND asc:47,0 (SCSI parity error)
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): Retrying command (per sense data)
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): READ(10). CDB: 28 00 00 8c 06 c1 00 00 04 00
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): CAM status: SCSI Status Error
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): SCSI status: Check Condition
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): SCSI sense: ABORTED COMMAND asc:47,0 (SCSI parity error)
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): Retrying command (per sense data)
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): READ(10). CDB: 28 00 00 8c 06 fe 00 00 01 00
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): CAM status: SCSI Status Error
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): SCSI status: Check Condition
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): SCSI sense: ABORTED COMMAND asc:47,0 (SCSI parity error)
Oct 8 14:28:51 S-STORE01 (da19:mpr0:0:19:0): Retrying command (per sense data)
Oct 8 14:29:51 S-STORE01 (da19:mpr0:0:19:0): SERVICE ACTION IN(16). CDB: 9e 10 00 00 00 00 00 00 00 00 00 00 00 20 00 00 length 32 SMID 470 Command timeout on target 19(0x002e), 60000 set, 60.269963126 elapsed
Oct 8 14:29:51 S-STORE01 mpr0: At enclosure level 0, slot 19, connector name ( )
Oct 8 14:29:51 S-STORE01 mpr0: Sending abort to target 19 for SMID 470
Oct 8 14:29:51 S-STORE01 (da19:mpr0:0:19:0): SERVICE ACTION IN(16). CDB: 9e 10 00 00 00 00 00 00 00 00 00 00 00 20 00 00 length 32 SMID 470 Aborting command 0xfffffe01a72a2250
Oct 8 14:29:55 S-STORE01 mpr0: Finished abort recovery for target 19
Oct 8 14:29:55 S-STORE01 (da19:mpr0:0:19:0): READ(10). CDB: 28 00 00 4c 07 40 00 00 01 00
Oct 8 14:29:55 S-STORE01 (da19:mpr0:0:19:0): CAM status: SCSI Status Error
Oct 8 14:29:55 S-STORE01 (da19:mpr0:0:19:0): SCSI status: Check Condition
Oct 8 14:29:55 S-STORE01 (da19:mpr0:0:19:0): SCSI sense: ABORTED COMMAND asc:47,0 (SCSI parity error)
Oct 8 14:29:55 S-STORE01 (da19:mpr0:0:19:0): Retrying command (per sense data)
Oct 8 14:29:55 S-STORE01 (da19:mpr0:0:19:0): READ(16). CDB: 88 00 00 00 00 06 5d dc df ff 00 00 00 01 00 00
Oct 8 14:29:55 S-STORE01 (da19:mpr0:0:19:0): CAM status: SCSI Status Error
Oct 8 14:29:55 S-STORE01 (da19:mpr0:0:19:0): SCSI status: Check Condition
Oct 8 14:29:55 S-STORE01 (da19:mpr0:0:19:0): SCSI sense: ABORTED COMMAND asc:47,0 (SCSI parity error)
Oct 8 14:29:55 S-STORE01 (da19:mpr0:0:19:0): Retrying command (per sense data)
I have booted in to the HBA card and it can see all the cards fine there but that particular card is being recognised as a SATAII drive.
That particuar slot no matter what I insert is being recognised as SATAII.
Think my issue is a dodgy backplane.
I have created a pool though and ran a few benchmarks it hasn't thrown any errors so lets see how it goes.
I believe this firmware we both have is correct and is the latest.