UNIQUE constraint failed: storage_encrypteddisk.encrypted_provider

P

potatosword

Dabbler
Joined
Dec 30, 2018
Messages
44
I just added a new encrypted Z2 pool to my server but alas, one of my drives turned out to be DoA. Got the pool up and running and left it degraded while waiting for the new drive to arrive. New drive gets here and I start the re-silvering process and I get the above error. I try it again, same error. I start researching and poking around FreeNAS and I see the little "resilvering" icon up top. I check and it's progressing through a resilver despite throwing an error earlier - no problem - I'll let it finish.

Somewhere around 80% resilver we got a series of write errors that sent ATA from 0 to 1. In response, I ran a SMART test that completed without error. Then sometime after I went to bed ATA went from 1 to 2. Thought strangely FreeNAS never reported this.

Code:
smartctl 7.0 2018-12-30 r4883 [FreeBSD 11.3-RELEASE-p9 amd64] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 2.5 5400
Device Model:     ST2000LM015-2E8174
Serial Number:    WDZ4CGA0
LU WWN Device Id: 5 000c50 0a9459904
Firmware Version: SDM1
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-3 T13/2161-D revision 3b
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Sat Jun 20 08:58:44 2020 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (    0) seconds.
Offline data collection
capabilities:                    (0x71) SMART execute Offline immediate.
                                        No Auto Offline data collection support.
                                        Suspend Offline collection upon new
                                        command.
                                        No Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        ( 325) minutes.
Conveyance self-test routine
recommended polling time:        (   2) minutes.
SCT capabilities:              (0x3035) SCT Status supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   074   067   006    Pre-fail  Always       -       23965580
  3 Spin_Up_Time            0x0003   099   099   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       12
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   066   060   045    Pre-fail  Always       -       3600148
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       19 (54 33 0)
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       10
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   061   051   040    Old_age   Always       -       39 (Min/Max 29/45)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       1
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       1
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       34
194 Temperature_Celsius     0x0022   039   049   000    Old_age   Always       -       39 (0 21 0 0 0)
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       18 (71 184 0)
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       686007324
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       70380573
254 Free_Fall_Sensor        0x0032   100   100   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 2
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 2 occurred at disk power-on lifetime: 19 hours (0 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 51 00 ff ff ff 0f

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ea 00 00 00 00 00 00 00      12:25:03.719  FLUSH CACHE EXT
  b0 d5 01 01 4f c2 00 00      12:22:17.834  SMART READ LOG
  b0 d5 01 06 4f c2 00 00      12:22:17.752  SMART READ LOG
  b0 d0 01 00 4f c2 00 00      12:22:17.637  SMART READ DATA
  b0 da 00 00 4f c2 00 00      12:22:17.579  SMART RETURN STATUS

Error 1 occurred at disk power-on lifetime: 11 hours (0 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 71 03 06 02 0c 40  Device Fault; Error: ABRT at LBA = 0x000c0206 = 786950

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 00 00 ff ff ff 4f 00      04:45:00.717  WRITE FPDMA QUEUED
  61 00 00 ff ff ff 4f 00      04:45:00.717  WRITE FPDMA QUEUED
  61 00 00 ff ff ff 4f 00      04:45:00.717  WRITE FPDMA QUEUED
  61 00 00 ff ff ff 4f 00      04:45:00.717  WRITE FPDMA QUEUED
  61 00 00 ff ff ff 4f 00      04:45:00.717  WRITE FPDMA QUEUED

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%        17         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


Now we seem to be scanning the resilver with an ever-growing time remaining. My gut feeling is that this is related to the original error that was thrown but what do I know.

1592661749826.png
 
sretalla

sretalla

Powered by Neutrality
Moderator
Joined
Jan 1, 2016
Messages
9,703
What is dmesg telling you?
 
P

potatosword

Dabbler
Joined
Dec 30, 2018
Messages
44
Code:
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 70 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 70 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Error 5, Retries exhausted
GEOM_ELI: g_eli_read_done() failed (error=5) gptid/5663633e-b296-11ea-a0f2-bc5ff4c98f8a.eli[READ(offset=1989661417472, length=4096)]
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Error 5, Retries exhausted
GEOM_ELI: g_eli_read_done() failed (error=5) gptid/5663633e-b296-11ea-a0f2-bc5ff4c98f8a.eli[READ(offset=1989661421568, length=4096)]
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 70 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 70 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 70 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 70 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 70 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Error 5, Retries exhausted
GEOM_ELI: g_eli_read_done() failed (error=5) gptid/5663633e-b296-11ea-a0f2-bc5ff4c98f8a.eli[READ(offset=1989661417472, length=4096)]
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 80 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 80 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 80 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 80 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 80 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Error 5, Retries exhausted
GEOM_ELI: g_eli_read_done() failed (error=5) gptid/5663633e-b296-11ea-a0f2-bc5ff4c98f8a.eli[READ(offset=0, length=4096)]
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 88 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 88 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 88 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 88 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 88 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Error 5, Retries exhausted
GEOM_ELI: g_eli_read_done() failed (error=5) gptid/5663633e-b296-11ea-a0f2-bc5ff4c98f8a.eli[READ(offset=4096, length=4096)]
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 80 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 80 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 80 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 80 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 80 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Error 5, Retries exhausted
GEOM_ELI: g_eli_read_done() failed (error=5) gptid/5663633e-b296-11ea-a0f2-bc5ff4c98f8a.eli[READ(offset=0, length=4096)]
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Error 5, Retries exhausted
GEOM_ELI: g_eli_read_done() failed (error=5) gptid/5663633e-b296-11ea-a0f2-bc5ff4c98f8a.eli[READ(offset=1989661421568, length=4096)]
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 e8 e0 88 78 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Error 5, Retries exhausted
GEOM_ELI: g_eli_read_done() failed (error=5) gptid/5663633e-b296-11ea-a0f2-bc5ff4c98f8a.eli[READ(offset=1989661421568, length=4096)]
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 c0 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 c0 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 c0 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 c0 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Retrying command (per sense data)
(da5:mps0:0:8:0): READ(10). CDB: 28 00 01 40 00 c0 00 00 08 00
(da5:mps0:0:8:0): CAM status: SCSI Status Error
(da5:mps0:0:8:0): SCSI status: Check Condition
(da5:mps0:0:8:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da5:mps0:0:8:0): Error 5, Retries exhausted
GEOM_ELI: g_eli_read_done() failed (error=5) gptid/5663633e-b296-11ea-a0f2-bc5ff4c98f8a.eli[READ(offset=32768, length=4096)]
 
P

potatosword

Dabbler
Joined
Dec 30, 2018
Messages
44
Honestly I just ended up destroying the pool and re-creating it as non-encrypted - since it's brand new I have that option. SMART test is running again with no issues so far. It's just slightly alarming that re-silvering might not be an option for me on encrypted pools.
 
Last edited:
sretalla

sretalla

Powered by Neutrality
Moderator
Joined
Jan 1, 2016
Messages
9,703
dmesg is pretty clear that you have some issues with da5.

Maybe it's cabling or the connection of the disk to the backplane... could be a bunch of things. I don't have the conversion in mind to check your SMART output numbers, so I'll assume those are showing no errors and that it's all about the cabling or controller.
 
P

potatosword

Dabbler
Joined
Dec 30, 2018
Messages
44
I suppose we'll see. I'm filling the pool with data right now and after that I'll probably scrub just to be sure. I would expect the error to present again since I haven't touched any hardware yet. If it doesn't pop up again I guess I'll throw my hands up.

Heads up here though: No backplane - this one is connected to an LSI HBA card.
 
P

potatosword

Dabbler
Joined
Dec 30, 2018
Messages
44
Ok we're getting the Logcal unit not ready errors on da3 now instead of da5. So that's weird but indicates something else is going on. I'm going to crack open the case and re-do some cables.

Edit: Ok back to putting data onto the pool. Looks like some SATA connections were pretty close to a whole tangle of power chords so maybe some EMF there? Idk.

Edit 2: Alright. Filled almost half way with data and then did a scrub. No errors to speak of. My guess is EMF caused by the SATA cables basically touching the power supply.
 
Last edited:
P

potatosword

Dabbler
Joined
Dec 30, 2018
Messages
44
Ran SMART overnight on all of them and got 8 unrecoverable and 8 unreadable sectors on da5. Further sign the drive is dying? Should I return it?
 
Samuel Tai

Samuel Tai

Never underestimate your own stupidity
Moderator
Joined
Apr 24, 2020
Messages
5,399
P

potatosword

Dabbler
Joined
Dec 30, 2018
Messages
44
Well you just sent me down a rabbit hole! I'll compile info for a return - thanks!

Do you think the ST2000LM003 would be free of SMR? I don't see it on the ixsystems forum list. I have a few ST2000LM007's in this pool and they all seem fine.
 
Samuel Tai

Samuel Tai

Never underestimate your own stupidity
Moderator
Joined
Apr 24, 2020
Messages
5,399
According to the Seagate data sheet, these models should still be CMR.
 
You must log in or register to reply here.

Similar threads

danb35
  • Locked
Trust this drive?
Replies
7
Views
3K
cyberjock
C
N
  • Locked
Disk Failure?
Replies
5
Views
1K
nick3333
N
M
16 Disk Errors at once
Replies
3
Views
1K
joeschmuck
joeschmuck
amorak
HDD SMART Test Results
Replies
3
Views
2K
Chris Moore
Chris Moore
C
  • Locked
Smart errors
Replies
5
Views
2K
Hyperion
Hyperion
Top