So, I got the dreaded SMART error email today. I've got 15 current_pending_sector and offline_unreadable errors. I've been following this procedure to scan and try to fix it; so far it doesn't seem to be working.
Any tips would be appreciated. Here's my most recent output from smartctl -a.
The errors toward the end seem to have occurred while I was trying to scan and fix.
Any tips would be appreciated. Here's my most recent output from smartctl -a.
The errors toward the end seem to have occurred while I was trying to scan and fix.
Code:
=== START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST3000DM001-1CH166 Serial Number: <redacted> LU WWN Device Id: 5 000c50 04e2acf1e Firmware Version: CC43 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Feb 22 17:26:04 2014 CST ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/223651en SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 584) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 338) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 111 099 006 Pre-fail Always - 215395677 3 Spin_Up_Time 0x0003 092 091 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 40 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 8 7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail Always - 20338659 9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 11770 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 40 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 094 094 000 Old_age Always - 6 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0 189 High_Fly_Writes 0x003a 099 099 000 Old_age Always - 1 190 Airflow_Temperature_Cel 0x0022 065 057 045 Old_age Always - 35 (Min/Max 28/43) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 19 193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 2878 194 Temperature_Celsius 0x0022 035 043 000 Old_age Always - 35 (0 21 0 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 15 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 15 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 2983h+11m+29.436s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 20530174758 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 20851656301 SMART Error Log Version: 1 ATA Error Count: 5 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 occurred at disk power-on lifetime: 11768 hours (490 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 01 ff ff ff 4f 00 1d+12:52:04.880 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 1d+12:52:04.854 READ LOG EXT 60 00 01 ff ff ff 4f 00 1d+12:52:01.992 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 1d+12:52:01.937 READ LOG EXT 60 00 01 ff ff ff 4f 00 1d+12:51:59.079 READ FPDMA QUEUED Error 4 occurred at disk power-on lifetime: 11768 hours (490 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 01 ff ff ff 4f 00 1d+12:52:01.992 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 1d+12:52:01.937 READ LOG EXT 60 00 01 ff ff ff 4f 00 1d+12:51:59.079 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 1d+12:51:59.053 READ LOG EXT 60 00 01 ff ff ff 4f 00 1d+12:51:56.199 READ FPDMA QUEUED Error 3 occurred at disk power-on lifetime: 11768 hours (490 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 01 ff ff ff 4f 00 1d+12:51:59.079 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 1d+12:51:59.053 READ LOG EXT 60 00 01 ff ff ff 4f 00 1d+12:51:56.199 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 1d+12:51:56.119 READ LOG EXT 60 00 01 ff ff ff 4f 00 1d+12:51:52.953 READ FPDMA QUEUED Error 2 occurred at disk power-on lifetime: 11768 hours (490 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 01 ff ff ff 4f 00 1d+12:51:56.199 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 1d+12:51:56.119 READ LOG EXT 60 00 01 ff ff ff 4f 00 1d+12:51:52.953 READ FPDMA QUEUED b0 d1 01 01 4f c2 40 00 1d+12:36:39.000 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] b0 d0 01 00 4f c2 40 00 1d+12:36:38.931 SMART READ DATA Error 1 occurred at disk power-on lifetime: 11768 hours (490 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 01 ff ff ff 4f 00 1d+12:51:52.953 READ FPDMA QUEUED b0 d1 01 01 4f c2 40 00 1d+12:36:39.000 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] b0 d0 01 00 4f c2 40 00 1d+12:36:38.931 SMART READ DATA ec 00 01 00 00 00 40 00 1d+12:36:38.929 IDENTIFY DEVICE b0 d5 01 01 4f c2 40 00 1d+12:31:44.262 SMART READ LOG SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 11769 4142374576 # 2 Extended offline Completed: read failure 30% 11765 4142374576 # 3 Extended offline Aborted by host 90% 11759 - # 4 Short offline Completed without error 00% 6766 - # 5 Short offline Completed without error 00% 6765 - # 6 Short offline Completed without error 00% 6764 - # 7 Short offline Completed without error 00% 6763 - # 8 Short offline Completed without error 00% 6762 - # 9 Short offline Completed without error 00% 6761 - #10 Short offline Completed without error 00% 6760 - #11 Short offline Completed without error 00% 6759 - #12 Short offline Completed without error 00% 6758 - #13 Short offline Completed without error 00% 6757 - #14 Short offline Completed without error 00% 6756 - #15 Short offline Completed without error 00% 6756 - #16 Short offline Completed without error 00% 6754 - #17 Short offline Completed without error 00% 6753 - #18 Short offline Completed without error 00% 6752 - #19 Short offline Completed without error 00% 6751 - #20 Short offline Completed without error 00% 6750 - #21 Short offline Completed without error 00% 6749 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.