Hi all,
I've been using Freenas for quit a while now and enjoy it a lot. althought I have some issues with the jails all is going ok until last week.
All of a sudden the following issue showed up in console.
Feb 3 12:55:48 nas smartd[2569]: Device: /dev/ada3, 24 Currently unreadable (pending) sectors
Feb 3 12:55:48 nas smartd[2569]: Device: /dev/ada3, 10 Offline uncorrectable sectors
Did a smart short test and long test but not sure what to do. Do i need to replace the disk (won't be an issue as long how to do it save).
Any help would be appreciated cause I'm just not that much into freebsd or linux.
did a bit off reading in this forum and found some things that should make thing more clear.
I'm talking about a zpool with 4 disks (all kind of sizes and brands) for storage of not really important data.
Movies, series and music. I really would like keep this data because i've been saving this for years but the amount is to much to backup.
I also did a zpool status -v which does not show any errors except for non-native block size on 1 disk. This is there since I started and could not hurt anything according earlier reading.
pool: bulkpool
state: ONLINE
status: One or more devices are configured to use a non-native block size.
Expect reduced performance.
action: Replace affected devices with devices that support the
configured block size, or migrate data to a properly configured
pool.
scan: scrub repaired 0 in 13h26m with 0 errors on Sun Dec 28 13:26:35 2014
config:
NAME STATE READ WRITE CKSUM
bulkpool ONLINE 0 0 0
gptid/37df9564-0030-11e2-8c06-d43d7e27dfda ONLINE 0 0 0
gptid/411b4ddf-0030-11e2-8c06-d43d7e27dfda ONLINE 0 0 0
gptid/9703fe45-00f9-11e2-8fd2-d43d7e27dfda ONLINE 0 0 0 block size: 512B configured, 4096B native
gptid/26a17eca-615c-11e4-be12-d43d7e27dfda ONLINE 0 0 0
errors: No known data errors
Now I also ran a
smartctl -A /dev/ada3 and added the results.
That doesn't make me happy If I interpreter it correctly.
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p8 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF READ SMART DATA SECTION ===
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 152 145 021 Pre-fail Always - 9375
4 Start_Stop_Count 0x0032 094 094 000 Old_age Always - 6387
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 049 049 000 Old_age Always - 37885
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 68
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 31
193 Load_Cycle_Count 0x0032 134 134 000 Old_age Always - 199578
194 Temperature_Celsius 0x0022 102 085 000 Old_age Always - 50
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 24
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 10
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 199 199 000 Old_age Offline - 378
Thanks Ralph
I've been using Freenas for quit a while now and enjoy it a lot. althought I have some issues with the jails all is going ok until last week.
All of a sudden the following issue showed up in console.
Feb 3 12:55:48 nas smartd[2569]: Device: /dev/ada3, 24 Currently unreadable (pending) sectors
Feb 3 12:55:48 nas smartd[2569]: Device: /dev/ada3, 10 Offline uncorrectable sectors
Did a smart short test and long test but not sure what to do. Do i need to replace the disk (won't be an issue as long how to do it save).
Any help would be appreciated cause I'm just not that much into freebsd or linux.
did a bit off reading in this forum and found some things that should make thing more clear.
I'm talking about a zpool with 4 disks (all kind of sizes and brands) for storage of not really important data.
Movies, series and music. I really would like keep this data because i've been saving this for years but the amount is to much to backup.
I also did a zpool status -v which does not show any errors except for non-native block size on 1 disk. This is there since I started and could not hurt anything according earlier reading.
pool: bulkpool
state: ONLINE
status: One or more devices are configured to use a non-native block size.
Expect reduced performance.
action: Replace affected devices with devices that support the
configured block size, or migrate data to a properly configured
pool.
scan: scrub repaired 0 in 13h26m with 0 errors on Sun Dec 28 13:26:35 2014
config:
NAME STATE READ WRITE CKSUM
bulkpool ONLINE 0 0 0
gptid/37df9564-0030-11e2-8c06-d43d7e27dfda ONLINE 0 0 0
gptid/411b4ddf-0030-11e2-8c06-d43d7e27dfda ONLINE 0 0 0
gptid/9703fe45-00f9-11e2-8fd2-d43d7e27dfda ONLINE 0 0 0 block size: 512B configured, 4096B native
gptid/26a17eca-615c-11e4-be12-d43d7e27dfda ONLINE 0 0 0
errors: No known data errors
Now I also ran a
smartctl -A /dev/ada3 and added the results.
That doesn't make me happy If I interpreter it correctly.
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p8 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF READ SMART DATA SECTION ===
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 152 145 021 Pre-fail Always - 9375
4 Start_Stop_Count 0x0032 094 094 000 Old_age Always - 6387
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 049 049 000 Old_age Always - 37885
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 68
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 31
193 Load_Cycle_Count 0x0032 134 134 000 Old_age Always - 199578
194 Temperature_Celsius 0x0022 102 085 000 Old_age Always - 50
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 24
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 10
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 199 199 000 Old_age Offline - 378
Thanks Ralph
Last edited: