sesipod
Contributor
- Joined
- Jan 27, 2017
- Messages
- 162
Wondering if these errors are serious enough to get replacement drives ordered ASAP ?
- DA6
Code:
root@nas:~ # smartctl -a -q noserial /dev/da6 smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.1-STABLE amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD30EFRX-68EUZN0 Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Oct 14 01:47:12 2018 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (40500) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 406) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 181 177 021 Pre-fail Always - 5908 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 214 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 049 049 000 Old_age Always - 37870 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 186 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 179 193 Load_Cycle_Count 0x0032 199 199 000 Old_age Always - 4283 194 Temperature_Celsius 0x0022 112 107 000 Old_age Always - 38 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 ATA Error Count: 10 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10 occurred at disk power-on lifetime: 2469 hours (102 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 01 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d5 01 e1 4f c2 00 08 6d+01:59:30.555 SMART READ LOG b0 d5 01 e1 4f c2 00 08 6d+01:59:30.555 SMART READ LOG b0 d5 01 e1 4f c2 00 08 6d+01:59:30.555 SMART READ LOG b0 d6 01 e0 4f c2 00 08 6d+01:59:30.554 SMART WRITE LOG b0 d6 01 e0 4f c2 00 08 6d+01:59:30.553 SMART WRITE LOG Error 9 occurred at disk power-on lifetime: 2469 hours (102 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 01 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d5 01 e1 4f c2 00 08 6d+01:59:30.555 SMART READ LOG b0 d5 01 e1 4f c2 00 08 6d+01:59:30.555 SMART READ LOG b0 d6 01 e0 4f c2 00 08 6d+01:59:30.554 SMART WRITE LOG b0 d6 01 e0 4f c2 00 08 6d+01:59:30.553 SMART WRITE LOG b0 d6 01 e0 4f c2 00 08 6d+01:59:30.552 SMART WRITE LOG Error 8 occurred at disk power-on lifetime: 2157 hours (89 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 01 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d5 01 e1 4f c2 00 08 00:57:43.540 SMART READ LOG b0 d5 01 e1 4f c2 00 08 00:57:43.539 SMART READ LOG b0 d6 01 e0 4f c2 00 08 00:57:43.539 SMART WRITE LOG b0 d6 01 e0 4f c2 00 08 00:57:43.538 SMART WRITE LOG b0 d5 01 e0 4f c2 00 08 00:57:43.538 SMART READ LOG Error 7 occurred at disk power-on lifetime: 1306 hours (54 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 01 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d5 01 e1 4f c2 00 08 28d+11:10:15.306 SMART READ LOG b0 d5 01 e1 4f c2 00 08 28d+11:10:15.306 SMART READ LOG b0 d6 01 e0 4f c2 00 08 28d+11:10:15.305 SMART WRITE LOG b0 d6 01 e0 4f c2 00 08 28d+11:10:15.304 SMART WRITE LOG b0 d5 01 e0 4f c2 00 08 28d+11:10:15.304 SMART READ LOG Error 6 occurred at disk power-on lifetime: 1306 hours (54 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 01 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d5 01 e1 4f c2 00 08 28d+11:09:43.472 SMART READ LOG b0 d5 01 e1 4f c2 00 08 28d+11:09:43.472 SMART READ LOG b0 d6 01 e0 4f c2 00 08 28d+11:09:43.471 SMART WRITE LOG b0 d6 01 e0 4f c2 00 08 28d+11:09:43.470 SMART WRITE LOG b0 d5 01 e0 4f c2 00 08 28d+11:09:43.470 SMART READ LOG SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 31474 - # 2 Short offline Completed without error 00% 31462 - # 3 Short offline Completed without error 00% 31450 - # 4 Short offline Completed without error 00% 31438 - # 5 Short offline Completed without error 00% 31402 - # 6 Short offline Completed without error 00% 31390 - # 7 Short offline Completed without error 00% 31354 - # 8 Short offline Completed without error 00% 31342 - # 9 Short offline Completed without error 00% 31306 - #10 Short offline Completed without error 00% 31294 - #11 Short offline Completed without error 00% 31258 - #12 Short offline Completed without error 00% 31246 - #13 Short offline Completed without error 00% 31234 - #14 Short offline Completed without error 00% 31222 - #15 Short offline Completed without error 00% 31186 - #16 Short offline Completed without error 00% 31174 - #17 Short offline Completed without error 00% 31138 - #18 Short offline Completed without error 00% 31126 - #19 Short offline Completed without error 00% 31090 - #20 Short offline Completed without error 00% 31079 - #21 Short offline Completed without error 00% 31042 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
- DA7
Code:
root@nas:~ # smartctl -a -q noserial /dev/da7 smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.1-STABLE amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD30EFRX-68EUZN0 Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Oct 14 01:44:28 2018 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (40320) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 404) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 182 178 021 Pre-fail Always - 5875 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 214 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 049 049 000 Old_age Always - 37871 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 186 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 179 193 Load_Cycle_Count 0x0032 199 199 000 Old_age Always - 4287 194 Temperature_Celsius 0x0022 111 106 000 Old_age Always - 39 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 ATA Error Count: 7 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 7 occurred at disk power-on lifetime: 2469 hours (102 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 01 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d5 01 e1 4f c2 00 08 6d+01:59:13.092 SMART READ LOG b0 d5 01 e1 4f c2 00 08 6d+01:59:13.092 SMART READ LOG b0 d6 01 e0 4f c2 00 08 6d+01:59:13.091 SMART WRITE LOG b0 d6 01 e0 4f c2 00 08 6d+01:59:13.090 SMART WRITE LOG b0 d5 01 e0 4f c2 00 08 6d+01:59:13.090 SMART READ LOG Error 6 occurred at disk power-on lifetime: 2157 hours (89 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 01 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d5 01 e1 4f c2 00 08 00:57:50.286 SMART READ LOG b0 d5 01 e1 4f c2 00 08 00:57:50.286 SMART READ LOG b0 d6 01 e0 4f c2 00 08 00:57:50.285 SMART WRITE LOG b0 d6 01 e0 4f c2 00 08 00:57:50.284 SMART WRITE LOG b0 d5 01 e0 4f c2 00 08 00:57:50.284 SMART READ LOG Error 5 occurred at disk power-on lifetime: 1306 hours (54 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 01 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d5 01 e1 4f c2 00 08 28d+11:10:25.795 SMART READ LOG b0 d5 01 e1 4f c2 00 08 28d+11:10:25.795 SMART READ LOG b0 d6 01 e0 4f c2 00 08 28d+11:10:25.794 SMART WRITE LOG b0 d6 01 e0 4f c2 00 08 28d+11:10:25.793 SMART WRITE LOG b0 d5 01 e0 4f c2 00 08 28d+11:10:25.793 SMART READ LOG Error 4 occurred at disk power-on lifetime: 1306 hours (54 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 01 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d5 01 e1 4f c2 00 08 28d+11:09:05.420 SMART READ LOG b0 d5 01 e1 4f c2 00 08 28d+11:09:05.420 SMART READ LOG b0 d6 01 e0 4f c2 00 08 28d+11:09:05.419 SMART WRITE LOG b0 d6 01 e0 4f c2 00 08 28d+11:09:05.418 SMART WRITE LOG b0 d5 01 e0 4f c2 00 08 28d+11:09:05.418 SMART READ LOG Error 3 occurred at disk power-on lifetime: 1306 hours (54 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 01 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d5 01 e1 4f c2 00 08 28d+11:04:20.596 SMART READ LOG b0 d5 01 e1 4f c2 00 08 28d+11:04:20.596 SMART READ LOG b0 d6 01 e0 4f c2 00 08 28d+11:04:20.595 SMART WRITE LOG b0 d6 01 e0 4f c2 00 08 28d+11:04:20.594 SMART WRITE LOG b0 d5 01 e0 4f c2 00 08 28d+11:04:20.594 SMART READ LOG SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 31475 - # 2 Short offline Completed without error 00% 31463 - # 3 Short offline Completed without error 00% 31451 - # 4 Short offline Completed without error 00% 31439 - # 5 Short offline Completed without error 00% 31403 - # 6 Short offline Completed without error 00% 31391 - # 7 Short offline Completed without error 00% 31355 - # 8 Short offline Completed without error 00% 31344 - # 9 Short offline Completed without error 00% 31308 - #10 Short offline Completed without error 00% 31296 - #11 Short offline Completed without error 00% 31260 - #12 Short offline Completed without error 00% 31248 - #13 Short offline Completed without error 00% 31236 - #14 Short offline Completed without error 00% 31224 - #15 Short offline Completed without error 00% 31188 - #16 Short offline Completed without error 00% 31176 - #17 Short offline Completed without error 00% 31140 - #18 Short offline Completed without error 00% 31128 - #19 Short offline Completed without error 00% 31092 - #20 Short offline Completed without error 00% 31080 - #21 Short offline Completed without error 00% 31044 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.