BritshGOAT
Cadet
- Joined
- Mar 4, 2022
- Messages
- 2
Hi, I've started rebuilding my NAS, creating from a fresh start using previous drives. before I start filling my pool up, I checked every drives S.M.A.R.T
When running a LONG test 2 of my drives
give me the following alert
Looking at the smartctl output I can't tell if they are dying or not, as it shows the smart test passed. I think ./sda is dying as its has values in LBA_of_first_error column but this is only a guess? as my pool will be a single raidz2 vdev, should I change these out before starting to use my NAS again or just upgrade 1?
When running a LONG test 2 of my drives
give me the following alert
Code:
Device: /dev/sdd [SAT], Self-Test Log error count increased from 3 to 4. Device: /dev/sdd [SAT], Self-Test Log error count increased from 3 to 4.
Looking at the smartctl output I can't tell if they are dying or not, as it shows the smart test passed. I think ./sda is dying as its has values in LBA_of_first_error column but this is only a guess? as my pool will be a single raidz2 vdev, should I change these out before starting to use my NAS again or just upgrade 1?
Code:
=== START OF INFORMATION SECTION === Model Family: Seagate IronWolf Pro Device Model: ST10000NE0008-2JM101 Serial Number: ZHZ3P5X0 LU WWN Device Id: 5 000c50 0c2bc47e0 Firmware Version: EN01 User Capacity: 10,000,831,348,736 bytes [10.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Oct 31 05:29:43 2023 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 249) Self-test routine in progress... 90% of test remaining. Total time to complete Offline data collection: ( 567) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 978) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x50bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 083 064 044 Pre-fail Always - 195058177 3 Spin_Up_Time 0x0003 092 090 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 167 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 96 7 Seek_Error_Rate 0x000f 089 060 045 Pre-fail Always - 786170628 9 Power_On_Hours 0x0032 077 077 000 Old_age Always - 20784 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 169 18 Head_Health 0x000b 100 100 050 Pre-fail Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 099 000 Old_age Always - 1 190 Airflow_Temperature_Cel 0x0022 061 023 040 Old_age Always In_the_past 39 (48 120 39 32 0) 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 112 193 Load_Cycle_Count 0x0032 093 093 000 Old_age Always - 14203 194 Temperature_Celsius 0x0022 039 077 000 Old_age Always - 39 (0 13 0 0 0) 195 Hardware_ECC_Recovered 0x001a 083 064 000 Old_age Always - 195058177 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 8 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 8 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Pressure_Limit 0x0023 100 100 001 Pre-fail Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 19365h+54m+31.004s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 94449578193 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 498694099818 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Self-test routine in progress 90% 20784 - # 2 Extended offline Completed: read failure 90% 20784 - # 3 Short offline Completed: read failure 90% 20713 - # 4 Short offline Completed: read failure 90% 20600 - # 5 Short offline Completed: read failure 90% 20432 - # 6 Extended offline Completed without error 00% 20395 - # 7 Short offline Completed: read failure 90% 20313 - # 8 Short offline Completed: read failure 90% 20145 - # 9 Short offline Completed: read failure 90% 20000 - #10 Short offline Completed: read failure 90% 19832 - #11 Extended offline Completed without error 00% 19730 - #12 Short offline Completed without error 00% 19664 - #13 Extended offline Interrupted (host reset) 00% 18831 - #14 Extended offline Interrupted (host reset) 00% 18810 - #15 Extended offline Completed without error 00% 18796 - #16 Extended offline Completed without error 00% 18772 - #17 Extended offline Completed without error 00% 18748 - #18 Extended offline Completed without error 00% 18724 - #19 Extended offline Completed without error 00% 18690 - #20 Extended offline Completed: read failure 90% 18637 - #21 Extended offline Completed: read failure 90% 18613 - 6 of 10 failed self-tests are outdated by newer successful extended offline self-test # 6 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
Code:
=== START OF INFORMATION SECTION === Model Family: Seagate BarraCuda 3.5 Device Model: ST8000DM004-2CX188 Serial Number: WSC07XF1 LU WWN Device Id: 5 000c50 0d637dda3 Firmware Version: 0001 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5425 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Oct 31 05:43:57 2023 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 999) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x30a5) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 077 054 006 Pre-fail Always - 54799575 3 Spin_Up_Time 0x0003 092 091 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2253 5 Reallocated_Sector_Ct 0x0033 098 098 010 Pre-fail Always - 4736 7 Seek_Error_Rate 0x000f 095 060 045 Pre-fail Always - 2826869110 9 Power_On_Hours 0x0032 081 081 000 Old_age Always - 16984 (68 15 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 195 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 030 030 000 Old_age Always - 70 188 Command_Timeout 0x0032 100 098 000 Old_age Always - 6 6 14 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 064 027 040 Old_age Always In_the_past 36 (21 236 36 31 0) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 674 193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 2953 194 Temperature_Celsius 0x0022 036 073 000 Old_age Always - 36 (0 15 0 0 0) 195 Hardware_ECC_Recovered 0x001a 077 064 000 Old_age Always - 54799575 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 112 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 112 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 15797h+36m+33.903s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 73043916656 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 323584380662 SMART Error Log Version: 1 ATA Error Count: 70 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 70 occurred at disk power-on lifetime: 16951 hours (706 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 3d+13:12:48.374 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 3d+13:12:48.374 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 3d+13:12:48.373 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 3d+13:12:48.373 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 3d+13:12:48.360 READ FPDMA QUEUED Error 69 occurred at disk power-on lifetime: 16951 hours (706 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 80 ff ff ff 4f 00 3d+13:12:47.762 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 3d+13:12:47.762 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 3d+13:12:47.762 READ FPDMA QUEUED 60 00 90 ff ff ff 4f 00 3d+13:12:47.760 READ FPDMA QUEUED 60 00 78 ff ff ff 4f 00 3d+13:12:47.759 READ FPDMA QUEUED Error 68 occurred at disk power-on lifetime: 16946 hours (706 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 3d+08:46:02.688 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 3d+08:46:02.678 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 3d+08:46:02.678 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 3d+08:46:02.677 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 3d+08:46:02.676 READ FPDMA QUEUED Error 67 occurred at disk power-on lifetime: 16946 hours (706 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 3d+08:46:01.980 READ FPDMA QUEUED 60 00 08 ff ff ff 4f 00 3d+08:46:01.974 READ FPDMA QUEUED 60 00 08 ff ff ff 4f 00 3d+08:46:01.968 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 3d+08:46:01.963 READ FPDMA QUEUED 60 00 08 ff ff ff 4f 00 3d+08:46:01.962 READ FPDMA QUEUED Error 66 occurred at disk power-on lifetime: 16942 hours (705 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: WP at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 00 00 ff ff ff 4f 00 3d+04:42:49.107 WRITE FPDMA QUEUED 61 00 00 ff ff ff 4f 00 3d+04:42:49.107 WRITE FPDMA QUEUED 60 00 00 ff ff ff 4f 00 3d+04:42:49.104 READ FPDMA QUEUED 60 00 08 ff ff ff 4f 00 3d+04:42:49.045 READ FPDMA QUEUED 60 00 08 ff ff ff 4f 00 3d+04:42:49.041 READ FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 16984 - # 2 Extended offline Completed: read failure 90% 16984 - # 3 Short offline Completed without error 00% 16913 - # 4 Short offline Completed without error 00% 16758 - # 5 Short offline Completed: read failure 90% 16590 2806846328 # 6 Extended offline Completed: read failure 90% 16518 2806846328 # 7 Short offline Completed without error 00% 16472 - # 8 Short offline Completed: read failure 90% 16304 2806846328 # 9 Short offline Completed without error 00% 16158 - #10 Short offline Completed: read failure 90% 15990 - #11 Extended offline Completed: read failure 90% 15870 - #12 Short offline Completed without error 00% 15824 - #13 Short offline Completed without error 00% 15656 - #14 Short offline Completed without error 00% 15641 - #15 Extended offline Interrupted (host reset) 00% 15640 - #16 Short offline Completed without error 00% 15582 - #17 Short offline Completed without error 00% 15409 - #18 Short offline Completed without error 00% 15160 - #19 Short offline Completed without error 00% 14992 - #20 Short offline Completed without error 00% 14824 - #21 Extended offline Interrupted (host reset) 90% 14783 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.