Hi all,
New to the forum, never had problems but this morning i came down to a Panic error on my nas setup.
Hardware is above the recomended specs
i7 4770
16gb RAM
Boot drive = Sandisk Ultra 64gb (Pen Drive / USB Drive)
Drives:
2x 4.0TB Drives in Stripe - Pool Name : NAS1
2x 2.0TB in Mirror - Pool Name : NAS2
Pool - Nas2 has things like docs / photos etc and is perfectly fine (not yet imported - see below).
Pool - Nas1 has music/media and things that i can replace should it fail (which it may have)
So... The original error was
Stopped at kdb_enter+0x3b : movq $0,kdb_why
I rebuilt a new USB drive and setup the Nas again from scratch.. the initial wizard shows the NAS1 and NAS2 for import however NAS1 import via the gui produces the panic error again.
So i rebuilt the drive again and following some google searches imported NAS1 directly from the shell using zpool import -R /mnt NAS1 which flagged an error saying its in use by another machine (or something to that effect - i didnt write it down)
The next option advised was to use zpool import -f -F NAS1 which paused and looks like it worked.
if i run Zpool status i get the below..
pool: NAS1
state: ONLINE
scan: scrub repaired 0 in 0 days 10:34:40 with 0 errors on Sat Aug 17 11:09:42 2019
config:
NAME STATE READ WRITE CKSUM
NAS1 ONLINE 0 0 0
gptid/ebff6c15-84f3-11e7-ab5d-4439c450389d ONLINE 0 0 0
gptid/ecad9dd0-84f3-11e7-ab5d-4439c450389d ONLINE 0 0 0
errors: No known data errors
pool: freenas-boot
state: ONLINE
scan: none requested
config:
NAME STATE READ WRITE CKSUM
freenas-boot ONLINE 0 0 0
da0p2 ONLINE 0 0 0
errors: No known data errors
However i have no volumes in the gui
Any advice while im smashing google for answers?
Do i need to run other commands via the shell, if i read correctly the shell imports differently to the gui.
Any assistance is greatly appreciated
- Shaun
New to the forum, never had problems but this morning i came down to a Panic error on my nas setup.
Hardware is above the recomended specs
i7 4770
16gb RAM
Boot drive = Sandisk Ultra 64gb (Pen Drive / USB Drive)
Drives:
2x 4.0TB Drives in Stripe - Pool Name : NAS1
2x 2.0TB in Mirror - Pool Name : NAS2
Pool - Nas2 has things like docs / photos etc and is perfectly fine (not yet imported - see below).
Pool - Nas1 has music/media and things that i can replace should it fail (which it may have)
So... The original error was
Stopped at kdb_enter+0x3b : movq $0,kdb_why
I rebuilt a new USB drive and setup the Nas again from scratch.. the initial wizard shows the NAS1 and NAS2 for import however NAS1 import via the gui produces the panic error again.
So i rebuilt the drive again and following some google searches imported NAS1 directly from the shell using zpool import -R /mnt NAS1 which flagged an error saying its in use by another machine (or something to that effect - i didnt write it down)
The next option advised was to use zpool import -f -F NAS1 which paused and looks like it worked.
if i run Zpool status i get the below..
pool: NAS1
state: ONLINE
scan: scrub repaired 0 in 0 days 10:34:40 with 0 errors on Sat Aug 17 11:09:42 2019
config:
NAME STATE READ WRITE CKSUM
NAS1 ONLINE 0 0 0
gptid/ebff6c15-84f3-11e7-ab5d-4439c450389d ONLINE 0 0 0
gptid/ecad9dd0-84f3-11e7-ab5d-4439c450389d ONLINE 0 0 0
errors: No known data errors
pool: freenas-boot
state: ONLINE
scan: none requested
config:
NAME STATE READ WRITE CKSUM
freenas-boot ONLINE 0 0 0
da0p2 ONLINE 0 0 0
errors: No known data errors
However i have no volumes in the gui
Any advice while im smashing google for answers?
Do i need to run other commands via the shell, if i read correctly the shell imports differently to the gui.
Any assistance is greatly appreciated
- Shaun