Hey, I'm using an old PC as a NAS (with TrueNAS ofc) and I have a WD Red Pro rev.2 (2tb) which is disconnecting from TrueNAS after 20 days (or so) of running 24/7. After a reboot, everything is working as normal. But on my pool status, it has as Pool Status: DEGRADED (but it is working fine). I also took it away from the PC and tested on my main machine with HDD Sentinel. No errors.
Here is my smartctl output:
Any idea of why is this happening?
Here is my smartctl output:
Code:
Handle 0x7F00, DMI type 127, 4 bytes End Of Table root@truenas[~]# smartctl -a /dev/ada1 smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p11 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Pro Device Model: WDC WD2002FFSX-68PF8N0 Serial Number: WD-WCC6N4YZ8SH1 LU WWN Device Id: 5 0014ee 21453c886 Firmware Version: 81.00A81 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Jul 10 15:49:31 2022 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 209) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x203d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 142 137 021 Pre-fail Always - 5866 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 34 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 091 091 000 Old_age Always - 6955 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 34 16 Unknown_Attribute 0x0022 001 199 000 Old_age Always - 21389075343 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 24 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 15 194 Temperature_Celsius 0x0022 110 106 000 Old_age Always - 37 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0 SMART Error Log Version: 1 ATA Error Count: 149 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 149 occurred at disk power-on lifetime: 6583 hours (274 days + 7 hours) When the command that caused the error occurred, the device was in an unknownstate. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 00 b0 8e 55 40 Error: Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- Error 148 occurred at disk power-on lifetime: 6583 hours (274 days + 7 hours) When the command that caused the error occurred, the device was in an unknownstate. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 00 b0 8d 55 40 Error: Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- Error 147 occurred at disk power-on lifetime: 6583 hours (274 days + 7 hours) When the command that caused the error occurred, the device was in an unknownstate. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 00 b8 4e 51 40 Error: Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- Error 146 occurred at disk power-on lifetime: 6581 hours (274 days + 5 hours) When the command that caused the error occurred, the device was in an unknownstate. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 00 70 c3 53 40 Error: Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- Error 145 occurred at disk power-on lifetime: 6578 hours (274 days + 2 hours) When the command that caused the error occurred, the device was in an unknownstate. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 00 90 83 54 40 Error: Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 6944 - # 2 Extended offline Completed without error 00% 6920 - # 3 Extended offline Completed without error 00% 6896 - # 4 Extended offline Completed without error 00% 6872 - # 5 Extended offline Completed without error 00% 6848 - # 6 Extended offline Completed without error 00% 6824 - # 7 Extended offline Completed without error 00% 6800 - # 8 Extended offline Completed without error 00% 6776 - # 9 Extended offline Completed without error 00% 6752 - #10 Extended offline Completed without error 00% 6728 - #11 Extended offline Completed without error 00% 6704 - #12 Extended offline Completed without error 00% 6680 - #13 Extended offline Completed without error 00% 6656 - #14 Extended offline Completed without error 00% 6632 - #15 Extended offline Completed without error 00% 6608 - #16 Extended offline Interrupted (host reset) 50% 6583 - #17 Extended offline Completed without error 00% 6561 - #18 Extended offline Completed without error 00% 6537 - #19 Extended offline Completed without error 00% 6513 - #20 Extended offline Completed without error 00% 6489 - #21 Extended offline Completed without error 00% 6465 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing
Any idea of why is this happening?