Hi All,
I took a look at the thread about diagnosing drive failures and just wanted to know how severe my particular failure is. I ran a short test and came up with these results:
I'm currently running a long test which will finish in a few hours I'm hoping but just wanted to get the ball rolling with troubleshooting and if I should worry yet or not.
Thanks!
I took a look at the thread about diagnosing drive failures and just wanted to know how severe my particular failure is. I ran a short test and came up with these results:
Code:
root@freenas:~ # smartctl -a /dev/ada0 smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.1-STABLE amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD30EFRX-68AX9N0 Serial Number: WD-WMC1T1118726 LU WWN Device Id: 5 0014ee 602e3af15 Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 21 19:19:07 2020 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 118) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: (40080) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 402) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 184 165 021 Pre-fail Always - 5766 4 Start_Stop_Count 0x0032 097 097 000 Old_age Always - 3733 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 017 017 000 Old_age Always - 60599 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 139 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 84 193 Load_Cycle_Count 0x0032 199 199 000 Old_age Always - 3648 194 Temperature_Celsius 0x0022 107 102 000 Old_age Always - 43 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 1 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 60% 60585 1565557560 # 2 Short offline Completed: read failure 60% 60536 1565557560 # 3 Short offline Completed: read failure 60% 60488 1565557560 # 4 Extended offline Completed: read failure 10% 60443 1565557560 # 5 Short offline Completed: read failure 60% 60392 1565562080 # 6 Short offline Completed: read failure 60% 60344 1565562080 # 7 Short offline Completed: read failure 60% 60296 1565562080 # 8 Short offline Completed: read failure 60% 60248 1565562096 # 9 Short offline Completed: read failure 60% 60200 1565562096 #10 Short offline Completed: read failure 60% 60152 1565562080 #11 Extended offline Completed: read failure 10% 60107 1565562080 #12 Short offline Completed: read failure 60% 60082 1565562080 #13 Short offline Completed without error 00% 60032 - #14 Short offline Completed without error 00% 59984 - #15 Short offline Completed without error 00% 59936 - #16 Short offline Completed without error 00% 59888 - #17 Short offline Completed without error 00% 59840 - #18 Short offline Completed without error 00% 59792 - #19 Short offline Completed without error 00% 59745 - #20 Extended offline Completed without error 00% 59700 - #21 Short offline Completed without error 00% 59649 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
I'm currently running a long test which will finish in a few hours I'm hoping but just wanted to get the ball rolling with troubleshooting and if I should worry yet or not.
Thanks!