theflyingsquirrel
Cadet
- Joined
- Jan 15, 2021
- Messages
- 8
I recently installed an old drive into my TrueNAS system and use it for Transmission download folder.
And I get a lot of error each day.
It is all on the new installed drive and have IO slow and bad sector error.
On the disk status page, it shown healthy.
When I run the below command to display the result, there is a 60 sec or so delay which does not show in the other disks.
I did a long smart test and here is the output for
I think this is a SMR drive and the error is probably due to cache flush?
I am thinking to do a ATA secure erase on the drive. Would that help?
Is there a way to instruct the drive to write to the platter directly without using the cache?
Is there a way to disable resilvering just for this disk?
And I get a lot of error each day.
It is all on the new installed drive and have IO slow and bad sector error.
On the disk status page, it shown healthy.
When I run the below command to display the result, there is a 60 sec or so delay which does not show in the other disks.
I did a long smart test and here is the output for
Code:
smartctl -a /dev/ada4
Code:
smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p10 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST3000DM001-1E6166 Serial Number: W1F4CHVT LU WWN Device Id: 5 000c50 03d2be4bc Firmware Version: SC48 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Dec 8 16:12:04 2021 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 592) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 359) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3081) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 115 091 006 Pre-fail Always - 89721040 3 Spin_Up_Time 0x0003 091 090 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 085 085 020 Old_age Always - 15623 5 Reallocated_Sector_Ct 0x0033 099 099 010 Pre-fail Always - 656 7 Seek_Error_Rate 0x000f 060 051 030 Pre-fail Always - 648691413103 9 Power_On_Hours 0x0032 037 037 000 Old_age Always - 55315 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 344 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 3761 188 Command_Timeout 0x0032 100 084 000 Old_age Always - 1382 1383 1383 189 High_Fly_Writes 0x003a 001 001 000 Old_age Always - 236 190 Airflow_Temperature_Cel 0x0022 066 053 045 Old_age Always - 34 (Min/Max 23/35) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 130 193 Load_Cycle_Count 0x0032 010 010 000 Old_age Always - 181259 194 Temperature_Celsius 0x0022 034 047 000 Old_age Always - 34 (0 9 0 0 0) 197 Current_Pending_Sector 0x0012 001 001 000 Old_age Always - 28144 198 Offline_Uncorrectable 0x0010 001 001 000 Old_age Offline - 28144 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 13959h+06m+30.228s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 52074124230 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 63767549312 SMART Error Log Version: 1 ATA Error Count: 7436 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 7436 occurred at disk power-on lifetime: 41145 hours (1714 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 80 ff ff ff 4f 00 00:03:07.786 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.761 READ DMA EXT 25 00 10 ff ff ff 4f 00 00:03:07.746 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.745 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.711 READ DMA EXT Error 7435 occurred at disk power-on lifetime: 41145 hours (1714 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 80 ff ff ff 4f 00 00:03:07.786 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.761 READ DMA EXT 25 00 10 ff ff ff 4f 00 00:03:07.746 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.745 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.711 READ DMA EXT Error 7434 occurred at disk power-on lifetime: 41145 hours (1714 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 80 ff ff ff 4f 00 00:03:07.761 READ DMA EXT 25 00 10 ff ff ff 4f 00 00:03:07.746 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.745 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.711 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.678 READ DMA EXT Error 7433 occurred at disk power-on lifetime: 41145 hours (1714 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 80 ff ff ff 4f 00 00:03:07.761 READ DMA EXT 25 00 10 ff ff ff 4f 00 00:03:07.746 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.745 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.711 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.678 READ DMA EXT Error 7432 occurred at disk power-on lifetime: 41145 hours (1714 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 80 ff ff ff 4f 00 00:03:07.678 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.644 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.611 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.578 READ DMA EXT 25 00 80 ff ff ff 4f 00 00:03:07.544 READ DMA EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 55310 4068066632 # 2 Extended offline Interrupted (host reset) 90% 55306 - # 3 Conveyance offline Completed without error 00% 47737 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
I think this is a SMR drive and the error is probably due to cache flush?
I am thinking to do a ATA secure erase on the drive. Would that help?
Is there a way to instruct the drive to write to the platter directly without using the cache?
Is there a way to disable resilvering just for this disk?