Daily local security run

Status
Not open for further replies.
S

Scareh

Contributor
Joined
Jul 31, 2012
Messages
182
I have activated the automatic emails a few weeks back, never got anything special until i got this mail this morning:
Code:
 
 
Checking for uids of 0:
root 0
 
Checking for passwordless accounts:
 
Checking login.conf permissions:
 
Checking for ports with mismatched checksums:
 
freenas.local kernel log messages:
+++ /tmp/security.OHzaIbOb      2013-10-04 03:01:01.000000000 +0200
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 15 e7 0b c0 00 00 08 00 length 4096 SMID 101 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 65 10 00 00 90 00 length 73728 SMID 758 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 65 10 00 00 90 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 65 10 00 00 90 00 length 73728 SMID 618 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 15 e7 0b c0 00 00 08 00 length 4096 SMID 733 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 65 10 00 00 90 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 16 31 1e e0 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 11 0b 3c 38 00 00 08 00 length 4096 SMID 66 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 b0 70 00 00 40 00 length 32768 SMID 440 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 02 98 00 00 10 00 length 8192 SMID 903 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 02 58 00 00 30 00 length 24576 SMID 214 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 02 98 00 00 10 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 b1 30 00 00 10 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 5d d8 00 00 58 00 length 45056 SMID 248 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 b5 68 00 00 30 00 length 24576 SMID 892 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 b5 68 00 00 30 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 b5 e8 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 f4 20 00 00 30 00 length 24576 SMID 844 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 79 20 00 00 50 00 length 40960 SMID 501 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 f4 20 00 00 30 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 f4 98 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 2c e2 e0 60 00 00 08 00 length 4096 SMID 106 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 7b 60 00 00 48 00 length 36864 SMID 648 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 f9 d8 00 00 30 00 length 24576 SMID 471 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 7b 48 00 00 10 00 length 8192 SMID 499 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 f9 d8 00 00 30 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 2c e2 c7 40 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 fc 10 00 00 50 00 length 40960 SMID 930 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 fc 10 00 00 50 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 4b c0 a3 68 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 5a 76 fe c0 00 00 08 00 length 4096 SMID 501 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 32 a8 00 00 c0 00 length 98304 SMID 844 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 81 10 00 00 20 00 length 16384 SMID 762 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 07 98 00 00 18 00 length 12288 SMID 723 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 07 98 00 00 18 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 07 b0 00 00 10 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(16). CDB: 8a 00 00 00 00 01 5d 50 a2 78 00 00 00 08 00 00 length 4096 SMID 720 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(16). CDB: 8a 00 00 00 00 01 5d 50 a0 78 00 00 00 08 00 00 length 4096 SMID 122 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 00 40 02 78 00 00 08 00 length 4096 SMID 596 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 00 40 04 78 00 00 08 00 length 4096 SMID 361 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 00 40 02 78 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 08 c8 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 91 c0 00 00 10 00 length 8192 SMID 435 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 91 c0 00 00 10 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 2f a8 00 00 20 00 length 16384 SMID 405 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 2f 98 00 00 08 00 length 4096 SMID 475 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 99 20 00 00 30 00 length 24576 SMID 164 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 99 00 00 00 10 00 length 8192 SMID 386 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 99 10 00 00 08 00 length 4096 SMID 337 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 2f 78 00 00 18 00 length 12288 SMID 454 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 91 e0 00 00 30 00 length 24576 SMID 240 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 91 c0 00 00 18 00 length 12288 SMID 70 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 99 20 00 00 30 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 2f d0 00 00 10 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 9c 70 00 00 08 00 length 4096 SMID 81 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 9c 90 00 00 10 00 length 8192 SMID 766 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 32 a8 00 00 10 00 length 8192 SMID 504 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 32 90 00 00 08 00 length 4096 SMID 932 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 9c 78 00 00 08 00 length 4096 SMID 178 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 9c 70 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 26 17 fd 38 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 9a 38 00 00 18 00 length 12288 SMID 144 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 44 f0 00 00 28 00 length 20480 SMID 690 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 9a 58 00 00 30 00 length 24576 SMID 718 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 44 f0 00 00 28 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 0a 4d 7c d0 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 34 20 00 00 80 00 length 65536 SMID 455 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 a0 78 00 00 20 00 length 16384 SMID 295 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 33 88 00 00 20 00 length 16384 SMID 263 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 2a 50 00 00 c0 00 length 98304 SMID 366 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 33 e0 00 00 20 00 length 16384 SMID 523 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 53 28 00 00 18 00 length 12288 SMID 437 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 2a 50 00 00 c0 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 07 f8 cd 50 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 6e 08 00 00 50 00 length 40960 SMID 704 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 6e 08 00 00 50 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 3b aa 40 c8 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 c4 48 00 00 50 00 length 40960 SMID 693 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 ac 90 00 00 30 00 length 24576 SMID 657 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 ac 90 00 00 30 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 7f c7 7c 98 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 09 2c 88 00 00 08 00 length 4096 SMID 485 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 b3 80 00 00 08 00 length 4096 SMID 444 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 09 2c 90 00 00 08 00 length 4096 SMID 550 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 b3 88 00 00 08 00 length 4096 SMID 803 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 81 b3 80 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 1e ba 42 18 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
 
freenas.local login failures:
 
freenas.local refused connections:




any translation on what is happening and what i should do to resolve it? Or should i not be worried?
 
S

Scareh

Contributor
Joined
Jul 31, 2012
Messages
182
Code:
[root@freenas] ~# zpool status
  pool: BigDisk
 state: ONLINE
status: The pool is formatted using a legacy on-disk format.  The pool can
        still be used, but some features are unavailable.
action: Upgrade the pool using 'zpool upgrade'.  Once this is done, the
        pool will no longer be accessible on software that does not support feature
        flags.
  scan: scrub repaired 0 in 1h36m with 0 errors on Fri Sep 13 14:44:30 2013
config:
 
        NAME                                          STATE     READ WRITE CKSUM
        BigDisk                                       ONLINE       0     0     0
          gptid/9d779ca0-f208-11e2-b905-0015179cb91a  ONLINE       0     0     0
 
errors: No known data errors
 
  pool: Data2
 state: ONLINE
status: The pool is formatted using a legacy on-disk format.  The pool can
        still be used, but some features are unavailable.
action: Upgrade the pool using 'zpool upgrade'.  Once this is done, the
        pool will no longer be accessible on software that does not support feature
        flags.
  scan: scrub repaired 0 in 0h3m with 0 errors on Sun Sep 29 00:03:23 2013
config:
 
        NAME                                          STATE     READ WRITE CKSUM
        Data2                                         ONLINE       0     0     0
          gptid/e53068db-dd5a-11e2-b9a1-0015179cb91a  ONLINE       0     0     0
 
errors: No known data errors
 
  pool: Homez0mgBig
 state: ONLINE
status: The pool is formatted using a legacy on-disk format.  The pool can
        still be used, but some features are unavailable.
action: Upgrade the pool using 'zpool upgrade'.  Once this is done, the
        pool will no longer be accessible on software that does not support feature
        flags.
  scan: scrub repaired 0 in 2h42m with 0 errors on Fri Oct  4 12:59:14 2013
config:
 
        NAME                                          STATE     READ WRITE CKSUM
        Homez0mgBig                                   ONLINE       0     0     0
          gptid/d1769f4e-e4a1-11e1-9255-000f206e8aef  ONLINE       0     0     0
 
errors: No known data errors
 
  pool: Raidz2
 state: ONLINE
  scan: scrub repaired 0 in 0h8m with 0 errors on Fri Sep 27 21:57:05 2013
config:
 
        NAME                                            STATE     READ WRITE CKSUM
        Raidz2                                          ONLINE       0     0     0
          raidz2-0                                      ONLINE       0     0     0
            gptid/3aa9b35a-0c2b-11e3-8316-0015179cb91a  ONLINE       0     0     0
            gptid/3c789f2d-0c2b-11e3-8316-0015179cb91a  ONLINE       0     0     0
            gptid/3e4d0618-0c2b-11e3-8316-0015179cb91a  ONLINE       0     0     0
            gptid/40293b14-0c2b-11e3-8316-0015179cb91a  ONLINE       0     0     0
 
errors: No known data errors
 
C

cyberjock

Inactive Account
Joined
Mar 25, 2012
Messages
19,526
da6 is probably dying. Post the output of smartctl -a -q noserial /dev/da6.
 
Dusan

Dusan

Guru
Joined
Jan 29, 2013
Messages
1,165
Or maybe a bad da6 cable / connector (all those "Power on, reset, or bus device reset occurred").
 
C

cyberjock

Inactive Account
Joined
Mar 25, 2012
Messages
19,526
Dusan said:
Or maybe a bad da6 cable / connector (all those "Power on, reset, or bus device reset occurred").
Click to expand...

I thought the same thing, but with all of the read and write errors I tend to dismiss the cable as the cause. Guess we'll see. Cable problems do show up in the smartctl data so it'll be easy to point the finger once we have the smart info.
 
S

Scareh

Contributor
Joined
Jul 31, 2012
Messages
182
as requested:
Code:
 
[root@freenas] ~# smartctl -a -q noserial /dev/da6
smartctl 6.1 2013-03-16 r3800 [FreeBSD 9.1-STABLE amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
 
=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red (AF)
Device Model:     WDC WD30EFRX-68AX9N0
Firmware Version: 80.00A80
User Capacity:    3,000,592,982,016 bytes [3.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Sat Oct  5 09:44:11 2013 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
 
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
 
General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (40020) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off supp                                                                                                                               ort.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 401) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x70bd) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.
 
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_                                                                                                                               FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -                                                                                                                                      0
  3 Spin_Up_Time            0x0027   179   175   021    Pre-fail  Always       -                                                                                                                                      6025
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -                                                                                                                                      237
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -                                                                                                                                      0
  7 Seek_Error_Rate         0x002e   100   253   000    Old_age   Always       -                                                                                                                                      0
  9 Power_On_Hours          0x0032   099   099   000    Old_age   Always       -                                                                                                                                      1369
 10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -                                                                                                                                      0
 11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -                                                                                                                                      0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -                                                                                                                                      204
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -                                                                                                                                      30
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -                                                                                                                                      206
194 Temperature_Celsius     0x0022   123   105   000    Old_age   Always       -                                                                                                                                      27
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -                                                                                                                                      0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -                                                                                                                                      0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -                                                                                                                                      0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -                                                                                                                                      0
200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -                                                                                                                                      0
 
SMART Error Log Version: 1
No Errors Logged
 
SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA                                                                                                                               _of_first_error
# 1  Short offline       Completed without error       00%       700         -
 
SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
 
[root@freenas] ~#
 
C

cyberjock

Inactive Account
Joined
Mar 25, 2012
Messages
19,526
Somehow the last column of the smart attributes table was chopped off. Please repost that table. For example, here's the table for one of my drives...

Code:
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG    VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate    0x002f  200  200  051    Pre-fail  Always      -      0
  3 Spin_Up_Time            0x0027  156  144  021    Pre-fail  Always      -      9158
  4 Start_Stop_Count        0x0032  099  099  000    Old_age  Always      -      1029
  5 Reallocated_Sector_Ct  0x0033  200  200  140    Pre-fail  Always      -      0
  7 Seek_Error_Rate        0x002e  100  253  000    Old_age  Always      -      0
  9 Power_On_Hours          0x0032  062  062  000    Old_age  Always      -      27768
10 Spin_Retry_Count        0x0032  100  100  000    Old_age  Always      -      0
11 Calibration_Retry_Count 0x0032  100  100  000    Old_age  Always      -      0
12 Power_Cycle_Count      0x0032  100  100  000    Old_age  Always      -      485
192 Power-Off_Retract_Count 0x0032  200  200  000    Old_age  Always      -      476
193 Load_Cycle_Count        0x0032  200  200  000    Old_age  Always      -      1514
194 Temperature_Celsius    0x0022  121  099  000    Old_age  Always      -      31
196 Reallocated_Event_Count 0x0032  200  200  000    Old_age  Always      -      0
197 Current_Pending_Sector  0x0032  200  200  000    Old_age  Always      -      0
198 Offline_Uncorrectable  0x0030  200  200  000    Old_age  Offline      -      0
199 UDMA_CRC_Error_Count    0x0032  200  200  000    Old_age  Always      -      0
200 Multi_Zone_Error_Rate  0x0008  200  200  000    Old_age  Offline      -      1
 
S

Scareh

Contributor
Joined
Jul 31, 2012
Messages
182
sry about that
Code:
 
[root@freenas] ~# smartctl -a -q noserial /dev/da6
smartctl 6.1 2013-03-16 r3800 [FreeBSD 9.1-STABLE amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
 
=== START OF INFORMATION SECTION ===
Model Family:    Western Digital Red (AF)
Device Model:    WDC WD30EFRX-68AX9N0
Firmware Version: 80.00A80
User Capacity:    3,000,592,982,016 bytes [3.00 TB]
Sector Sizes:    512 bytes logical, 4096 bytes physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:  ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Sat Oct  5 10:02:28 2013 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
 
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
 
General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (  0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (40020) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (  2) minutes.
Extended self-test routine
recommended polling time:        ( 401) minutes.
Conveyance self-test routine
recommended polling time:        (  5) minutes.
SCT capabilities:              (0x70bd) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.
 
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG    VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate    0x002f  200  200  051    Pre-fail  Always      -      0
  3 Spin_Up_Time            0x0027  179  175  021    Pre-fail  Always      -      6025
  4 Start_Stop_Count        0x0032  100  100  000    Old_age  Always      -      237
  5 Reallocated_Sector_Ct  0x0033  200  200  140    Pre-fail  Always      -      0
  7 Seek_Error_Rate        0x002e  100  253  000    Old_age  Always      -      0
  9 Power_On_Hours          0x0032  099  099  000    Old_age  Always      -      1369
10 Spin_Retry_Count        0x0032  100  100  000    Old_age  Always      -      0
11 Calibration_Retry_Count 0x0032  100  100  000    Old_age  Always      -      0
12 Power_Cycle_Count      0x0032  100  100  000    Old_age  Always      -      204
192 Power-Off_Retract_Count 0x0032  200  200  000    Old_age  Always      -      30
193 Load_Cycle_Count        0x0032  200  200  000    Old_age  Always      -      206
194 Temperature_Celsius    0x0022  123  105  000    Old_age  Always      -      27
196 Reallocated_Event_Count 0x0032  200  200  000    Old_age  Always      -      0
197 Current_Pending_Sector  0x0032  200  200  000    Old_age  Always      -      0
198 Offline_Uncorrectable  0x0030  100  253  000    Old_age  Offline      -      0
199 UDMA_CRC_Error_Count    0x0032  200  200  000    Old_age  Always      -      0
200 Multi_Zone_Error_Rate  0x0008  100  253  000    Old_age  Offline      -      0
 
SMART Error Log Version: 1
No Errors Logged
 
SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline      Completed without error      00%      700        -
 
SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.



todays email report btw:

Code:
 
Checking for uids of 0:
root 0
 
Checking for passwordless accounts:
 
Checking login.conf permissions:
 
Checking for ports with mismatched checksums:
 
freenas.local kernel log messages:
+++ /tmp/security.hMiU1oLk      2013-10-05 03:01:08.000000000 +0200
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 84 b3 98 00 00 18 00 length 12288 SMID 833 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 43 b0 78 00 00 50 00 length 40960 SMID 366 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0c 58 f8 00 00 10 00 length 8192 SMID 803 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0c 59 20 00 00 28 00 length 20480 SMID 321 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 84 b3 c0 00 00 28 00 length 20480 SMID 746 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0c 59 08 00 00 08 00 length 4096 SMID 460 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0c 59 08 00 00 08 00
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 82 0e e0 00 00 10 00
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 82 1f c0 00 01 00 00 length 131072 SMID 338 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 82 1e c0 00 01 00 00 length 131072 SMID 680 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 82 20 c0 00 00 b0 00 length 90112 SMID 597 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 82 1a c0 00 01 00 00 length 131072 SMID 91 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 82 1d c0 00 01 00 00 length 131072 SMID 172 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 82 19 c0 00 01 00 00 length 131072 SMID 85 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 82 1c c0 00 01 00 00 length 131072 SMID 981 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 82 1b c0 00 01 00 00 length 131072 SMID 126 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 84 b8 68 00 00 a8 00 length 86016 SMID 558 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 82 19 c0 00 01 00 00
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 43 b3 90 00 00 20 00 length 16384 SMID 481 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 55 38 00 00 c0 00 length 98304 SMID 951 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 55 38 00 00 c0 00
 
freenas.local login failures:
Oct  4 19:11:46 freenas sshd[39069]: Invalid user admin from 192.168.0.1
Oct  4 19:11:46 freenas sshd[39069]: input_userauth_request: invalid user admin [preauth]
Oct  4 19:11:48 freenas sshd[39069]: Failed password for invalid user admin from 192.168.0.1 port 55314 ssh2
 
freenas.local refused connections:
 
Dusan

Dusan

Guru
Joined
Jan 29, 2013
Messages
1,165
Could you also please post output of:
smartctl -l sataphy /dev/da6
 
S

Scareh

Contributor
Joined
Jul 31, 2012
Messages
182
as requested:

Code:
 
[root@freenas] ~# smartctl -l sataphy /dev/da6
smartctl 6.1 2013-03-16 r3800 [FreeBSD 9.1-STABLE amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
 
SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2           77  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2           77  R_ERR response for host-to-device data FIS
0x0005  2           17  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2           17  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2           43  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2           44  Device-to-host register FISes sent due to a COMRESET
0x000b  2           38  CRC errors within host-to-device FIS
0x000f  2           28  R_ERR response for host-to-device data FIS, CRC
0x0012  2           10  R_ERR response for host-to-device non-data FIS, CRC
0x8000  4       456334  Vendor specific

any input or thoughts on whats wrong? i see something about a disk dieing? or a cable? or... ?
 
S

Scareh

Contributor
Joined
Jul 31, 2012
Messages
182
started a scrub last night before i went to bed, this is this mornings mail:

Code:
freenas.local kernel log messages:
+++ /tmp/security.86FqIlA0      2013-10-06 03:01:00.000000000 +0200
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 43 c0 08 00 00 20 00 length 16384 SMID 773 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 43 c0 38 00 00 10 00 length 8192 SMID 956 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 43 c0 08 00 00 20 00
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 00 a2 23 58 00 01 00 00
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 43 c0 50 00 00 68 00 length 53248 SMID 905 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 43 c0 50 00 00 68 00
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 00 d8 3f f0 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 84 d5 18 00 00 18 00 length 12288 SMID 278 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 43 c8 88 00 00 68 00 length 53248 SMID 717 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0c 7b 90 00 00 40 00 length 32768 SMID 774 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 84 d5 40 00 00 40 00 length 32768 SMID 583 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0c 7b 90 00 00 40 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 43 c1 8d c0 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 43 fb 20 00 00 20 00 length 16384 SMID 918 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 5e 58 00 00 c0 00 length 98304 SMID 687 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 5e 58 00 00 c0 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 0e db fe 38 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 21 88 00 00 08 00 length 4096 SMID 493 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0c ce 38 00 00 08 00 length 4096 SMID 742 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 14 f8 00 00 08 00 length 4096 SMID 956 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 21 80 00 00 08 00 length 4096 SMID 455 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 21 88 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 15 e4 19 50 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 45 98 00 00 20 00 length 16384 SMID 548 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 45 c8 00 00 10 00 length 8192 SMID 110 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 45 98 00 00 20 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 79 2a 29 e8 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 21 68 00 00 10 00 length 8192 SMID 344 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 66 38 00 00 18 00 length 12288 SMID 198 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 59 a8 00 00 18 00 length 12288 SMID 705 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 66 90 00 00 10 00 length 8192 SMID 993 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 21 38 00 00 20 00 length 16384 SMID 374 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 66 68 00 00 18 00 length 12288 SMID 1000 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 59 d0 00 00 20 00 length 16384 SMID 126 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 5a 00 00 00 10 00 length 8192 SMID 943 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 21 38 00 00 20 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 1a 52 cc 78 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 78 a0 00 00 18 00 length 12288 SMID 333 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 6c 68 00 00 18 00 length 12288 SMID 326 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 78 f8 00 00 10 00 length 8192 SMID 900 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 78 c8 00 00 20 00 length 16384 SMID 223 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 6c 38 00 00 20 00 length 16384 SMID 554 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 6c 10 00 00 18 00 length 12288 SMID 913 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 78 a0 00 00 18 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 23 e3 b3 70 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 7d 98 00 00 68 00 length 53248 SMID 108 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 8a 50 00 00 40 00 length 32768 SMID 283 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 8a 28 00 00 18 00 length 12288 SMID 710 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 8a 28 00 00 18 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 1b 56 5f 10 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 ac 98 00 00 08 00 length 4096 SMID 859 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 a0 10 00 00 08 00 length 4096 SMID 900 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 67 b8 00 00 10 00 length 8192 SMID 714 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 ac 90 00 00 08 00 length 4096 SMID 1004 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 a0 00 00 00 10 00 length 8192 SMID 462 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 a0 10 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 34 59 23 78 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 b2 40 00 00 18 00 length 12288 SMID 356 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 6d c0 00 00 10 00 length 8192 SMID 790 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 b2 98 00 00 10 00 length 8192 SMID 70 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 6d d8 00 00 10 00 length 8192 SMID 912 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 6d 98 00 00 18 00 length 12288 SMID 422 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 6d 68 00 00 18 00 length 12288 SMID 242 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 b2 78 00 00 10 00 length 8192 SMID 1018 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 b2 b0 00 00 10 00 length 8192 SMID 420 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 6d 68 00 00 18 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 35 2b 29 90 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 bc 68 00 00 20 00 length 16384 SMID 612 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 c9 50 00 00 10 00 length 8192 SMID 261 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 84 88 00 00 10 00 length 8192 SMID 469 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 84 38 00 00 10 00 length 8192 SMID 709 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 c9 20 00 00 20 00 length 16384 SMID 218 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 c8 f8 00 00 18 00 length 12288 SMID 436 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 84 58 00 00 20 00 length 16384 SMID 176 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 bc c0 00 00 18 00 length 12288 SMID 819 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 bc 90 00 00 20 00 length 16384 SMID 950 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 84 58 00 00 20 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 0a 83 f1 a8 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 bf a8 00 00 20 00 length 16384 SMID 950 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 bf d8 00 00 18 00 length 12288 SMID 500 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 bf a8 00 00 20 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 bf d8 00 00 10 00 length 8192 SMID 190 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 44 bf d8 00 00 10 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 39 70 d3 60 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+Solaris: WARNING: Disk, '/dev/gptid/9d779ca0-f208-11e2-b905-0015179cb91a', has a block alignment that is larger than the pool's alignment

to be continued in next post because of limit of 30k chars
 
S

Scareh

Contributor
Joined
Jul 31, 2012
Messages
182
continuation:

Code:
 
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 8e d0 00 00 10 00 length 8192 SMID 443 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 d3 28 00 00 08 00 length 4096 SMID 613 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 8e b0 00 00 10 00 length 8192 SMID 249 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 d3 00 00 00 18 00 length 12288 SMID 850 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 8e a0 00 00 08 00 length 4096 SMID 255 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 d3 38 00 00 10 00 length 8192 SMID 74 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 8e e8 00 00 08 00 length 4096 SMID 80 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 8e 78 00 00 20 00 length 16384 SMID 227 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 8e 78 00 00 20 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 3a 5f f5 90 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 9e 40 00 00 10 00 length 8192 SMID 840 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 9e 38 00 00 08 00 length 4096 SMID 614 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 e2 80 00 00 18 00 length 12288 SMID 975 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 e2 50 00 00 18 00 length 12288 SMID 187 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 9e a0 00 00 08 00 length 4096 SMID 832 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 9e 88 00 00 10 00 length 8192 SMID 999 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 9e 60 00 00 18 00 length 12288 SMID 867 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 e2 c0 00 00 08 00 length 4096 SMID 471 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 85 e2 a8 00 00 10 00 length 8192 SMID 700 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d 9e 40 00 00 10 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 29 2c 1b 38 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 0d d0 00 00 18 00 length 12288 SMID 698 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 1a 88 00 00 08 00 length 4096 SMID 575 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 0d f0 00 00 10 00 length 8192 SMID 802 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 0e 08 00 00 18 00 length 12288 SMID 768 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 0e 30 00 00 10 00 length 8192 SMID 312 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 1a 60 00 00 18 00 length 12288 SMID 834 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 1a c0 00 00 10 00 length 8192 SMID 669 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 1a 98 00 00 18 00 length 12288 SMID 641 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 1a 60 00 00 18 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 4a 71 da a0 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d e2 20 00 00 10 00 length 8192 SMID 441 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 26 40 00 00 10 00 length 8192 SMID 946 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 26 30 00 00 08 00 length 4096 SMID 427 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 28 48 00 00 c0 00 length 98304 SMID 430 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0d e2 08 00 00 10 00 length 8192 SMID 709 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 55 a0 00 00 c0 00 length 98304 SMID 128 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 19 98 00 00 10 00 length 8192 SMID 682 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 6b 50 00 00 c0 00 length 98304 SMID 224 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 55 a0 00 00 c0 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 4c 3b ff 40 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 6c 30 00 00 c0 00 length 98304 SMID 157 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 29 28 00 00 c0 00 length 98304 SMID 879 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 27 38 00 00 20 00 length 16384 SMID 629 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 33 d0 00 00 18 00 length 12288 SMID 253 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 29 28 00 00 c0 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 4f b3 20 50 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 66 f0 00 00 10 00 length 8192 SMID 299 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 66 f0 00 00 10 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 57 7f fc 68 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 7e e8 00 00 18 00 length 12288 SMID 286 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0e 3a c0 00 00 20 00 length 16384 SMID 986 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 65 f8 00 00 40 00 length 32768 SMID 777 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 66 50 00 00 80 00 length 65536 SMID 262 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 28 48 00 00 c0 00 length 98304 SMID 513 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 72 50 00 00 20 00 length 16384 SMID 662 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 6b 50 00 00 c0 00 length 98304 SMID 344 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 66 50 00 00 80 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 58 23 68 50 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 74 58 00 00 08 00 length 4096 SMID 626 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 80 f8 00 00 10 00 length 8192 SMID 168 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 81 30 00 00 08 00 length 4096 SMID 469 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 74 88 00 00 10 00 length 8192 SMID 724 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 81 18 00 00 10 00 length 8192 SMID 83 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 74 a0 00 00 08 00 length 4096 SMID 310 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 74 30 00 00 20 00 length 16384 SMID 732 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 80 c0 00 00 18 00 length 12288 SMID 230 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 80 e8 00 00 08 00 length 4096 SMID 883 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 74 68 00 00 10 00 length 8192 SMID 175 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 80 c0 00 00 18 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 57 dc ee 08 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 78 68 00 00 18 00 length 12288 SMID 593 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 78 68 00 00 18 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 59 1a b1 e0 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 99 90 00 00 10 00 length 8192 SMID 297 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 8d 00 00 00 18 00 length 12288 SMID 780 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 99 60 00 00 20 00 length 16384 SMID 618 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 8c a8 00 00 20 00 length 16384 SMID 994 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 99 38 00 00 18 00 length 12288 SMID 523 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 8c d0 00 00 20 00 length 16384 SMID 250 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 99 38 00 00 18 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 5f 43 81 e8 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 6b 30 00 00 c0 00 length 98304 SMID 352 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 9d e8 00 00 18 00 length 12288 SMID 145 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 6b 30 00 00 c0 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 60 65 fd 30 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 72 a0 00 00 60 00 length 49152 SMID 827 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 c3 b8 00 00 20 00 length 16384 SMID 273 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 86 d0 50 00 00 18 00 length 12288 SMID 230 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0e 8c 28 00 00 20 00 length 16384 SMID 929 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 80 2b a8 00 00 c0 00 length 98304 SMID 749 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 40 72 30 00 00 c0 00 length 98304 SMID 985 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 08 72 a0 00 00 60 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 68 a9 ec 50 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 d0 e0 00 00 68 00 length 53248 SMID 935 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 45 d0 e0 00 00 68 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 6a 29 45 b0 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 87 43 28 00 00 08 00 length 4096 SMID 343 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 46 36 a8 00 00 08 00 length 4096 SMID 184 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0e ff 18 00 00 08 00 length 4096 SMID 473 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0e fe f0 00 00 08 00 length 4096 SMID 253 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0e fe f8 00 00 18 00 length 12288 SMID 752 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 28 0e ff 18 00 00 08 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 4c ff 6e e0 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 87 55 a0 00 00 48 00 length 36864 SMID 338 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 46 48 e8 00 00 70 00 length 57344 SMID 973 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 87 55 a0 00 00 48 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 80 08 7d 90 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 46 4e f8 00 00 68 00 length 53248 SMID 391 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 87 5b b0 00 00 40 00 length 32768 SMID 605 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 87 5b 88 00 00 18 00 length 12288 SMID 725 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 87 5b 88 00 00 18 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 1d e4 35 98 00 01 00 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 87 6b a0 00 00 40 00 length 32768 SMID 502 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 46 5f 08 00 00 48 00 length 36864 SMID 413 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 99 46 5e e8 00 00 18 00 length 12288 SMID 196 terminated ioc 804b scsi 0 state c xfer 0
+(da6:mps0:0:7:0): WRITE(10). CDB: 2a 00 5d 87 6b a0 00 00 40 00
+(da6:mps0:0:7:0): CAM status: SCSI Status Error
+(da6:mps0:0:7:0): SCSI status: Check Condition
+(da6:mps0:0:7:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
+(da6:mps0:0:7:0): Retrying command (per sense data)
+(da6:mps0:0:7:0): READ(10). CDB: 28 00 3f e2 8d 20 00 01 00 00
 
C

cyberjock

Inactive Account
Joined
Mar 25, 2012
Messages
19,526
Well, its like this...

Your disk isn't reporting any errors from the disk. And its saying nothing is wrong with the communications(cable errors). So the most likely culprit is your SATA controller. What controller are you using?
 
S

Scareh

Contributor
Joined
Jul 31, 2012
Messages
182
i'm using the one you guys suggested: the IBM ServeRAID M1015
:/

if it is the controller shouldn't the other disk give some errors aswell?
 
C

cyberjock

Inactive Account
Joined
Mar 25, 2012
Messages
19,526
Depends on where the problem lies. If its part of the silicon for that one specific port, then no.
 
S

Scareh

Contributor
Joined
Jul 31, 2012
Messages
182
is there any command i can use to determine that the raid controller is 100% sure the cause off all these errors?
 
Dusan

Dusan

Guru
Joined
Jan 29, 2013
Messages
1,165
I agree with cyberjock that there isn't any problem with the data platters. There is definitely a problem with the disk <-> controller communication (all those SATA Phy R_ERR counters). Yes, the controller itself can be the cause, but I still think that the cables/connector or the disk's SATA interface can also be the reason. I would first try to change the SATA cable. To determine if it's the controller or the disk you could try to connect some other drive to the same controller port.
 
C

cyberjock

Inactive Account
Joined
Mar 25, 2012
Messages
19,526
Scareh said:
is there any command i can use to determine that the raid controller is 100% sure the cause off all these errors?
Click to expand...

Nope. The only reason I dismiss the cables is that communication errors show up under UDMA_CRC_Error_Count. All of your disks are zero. I'd expect that if you were having any communication issues at all that number would definitely be non-zero and probably 4+ digits(and your issues are serious from the reset messages). Even regular use has occasional hiccups in communcations. Of all of my disks, about half of them have single digit values for UDMA_CRC_Error_Count.
 
Status
Not open for further replies.

Similar threads

J
  • Locked
SOLVED CAM status: CCB request completed with an error
Replies
16
Views
25K
Jeremy Hays
J
J
  • Locked
Pulling hair out with building FreeNAS server
Replies
3
Views
1K
sfcredfox
sfcredfox
A
  • Locked
freenas rebooted on disk failure
Replies
8
Views
1K
armsby
A
W
ZFS Issues after power outage
Replies
3
Views
1K
weathermon
W
P
  • Locked
硬盘无法0数据填充
Replies
3
Views
5K
pipilang
P
Top