Hello,
I just added 3 drives to my Supermicro x7DBN/SC926TQ-R800LPB server (9 drives were already present). At first only one of the drives was recognized. I powered off the server and reseated the SATA cables between the chassis and the AOC-SA2-MV8 card (which these slots connect to) and powered it back on. All drives were then recognized OK, and everything is working OK.
However, I noticed some aprobe errors in dmesg when it booted, and I'm not sure what device they are referring to. I'm booting from a Sandisk Cruzer USB drive.
How can I tell what device it is talking about?
I just added 3 drives to my Supermicro x7DBN/SC926TQ-R800LPB server (9 drives were already present). At first only one of the drives was recognized. I powered off the server and reseated the SATA cables between the chassis and the AOC-SA2-MV8 card (which these slots connect to) and powered it back on. All drives were then recognized OK, and everything is working OK.
However, I noticed some aprobe errors in dmesg when it booted, and I'm not sure what device they are referring to. I'm booting from a Sandisk Cruzer USB drive.
Code:
Copyright (c) 1992-2013 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 9.2-RELEASE-p4 #0 r262572+17a4d3d: Wed Apr 23 10:09:38 PDT 2014 root@build3.ixsystems.com:/tank/home/jkh/build/9.2.1/freenas/os-base/amd64/fusion/jkh/9.2.1/freenas/FreeBSD/src/sys/FREENAS.amd64 amd64 gcc version 4.2.1 20070831 patched [FreeBSD] CPU: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz (2500.05-MHz K8-class CPU) Origin = "GenuineIntel" Id = 0x10676 Family = 0x6 Model = 0x17 Stepping = 6 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0xce3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,DCA,SSE4.1> AMD Features=0x20100800<SYSCALL,NX,LM> AMD Features2=0x1<LAHF> TSC: P-state invariant, performance statistics real memory = 34359738368 (32768 MB) avail memory = 33163694080 (31627 MB) Event timer "LAPIC" quality 400 ACPI APIC Table: <PTLTD APIC > FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs FreeBSD/SMP: 2 package(s) x 4 core(s) cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 cpu2 (AP): APIC ID: 2 cpu3 (AP): APIC ID: 3 cpu4 (AP): APIC ID: 4 cpu5 (AP): APIC ID: 5 cpu6 (AP): APIC ID: 6 cpu7 (AP): APIC ID: 7 WARNING: VIMAGE (virtualized network stack) is a highly experimental feature. ioapic0 <Version 2.0> irqs 0-23 on motherboard ioapic1 <Version 2.0> irqs 24-47 on motherboard kbd1 at kbdmux0 cryptosoft0: <software crypto> on motherboard aesni0: No AESNI support. padlock0: No ACE support. acpi0: <PTLTD RSDT> on motherboard acpi0: Power Button (fixed) unknown: I/O range not supported cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 cpu2: <ACPI CPU> on acpi0 cpu3: <ACPI CPU> on acpi0 cpu4: <ACPI CPU> on acpi0 cpu5: <ACPI CPU> on acpi0 cpu6: <ACPI CPU> on acpi0 cpu7: <ACPI CPU> on acpi0 atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 Event timer "RTC" frequency 32768 Hz quality 0 attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0 Timecounter "i8254" frequency 1193182 Hz quality 0 Event timer "i8254" frequency 1193182 Hz quality 100 Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pcib2: <ACPI PCI-PCI bridge> irq 16 at device 0.0 on pci1 pci2: <ACPI PCI bus> on pcib2 pcib3: <ACPI PCI-PCI bridge> irq 16 at device 0.0 on pci2 pci3: <ACPI PCI bus> on pcib3 pcib4: <ACPI PCI-PCI bridge> irq 18 at device 2.0 on pci2 pci4: <ACPI PCI bus> on pcib4 em0: <Intel(R) PRO/1000 Network Connection 7.3.8> port 0x2000-0x201f mem 0xd8800000-0xd881ffff irq 18 at device 0.0 on pci4 em0: Using an MSI interrupt em0: Ethernet address: 00:30:48:33:06:f2 em1: <Intel(R) PRO/1000 Network Connection 7.3.8> port 0x2020-0x203f mem 0xd8820000-0xd883ffff irq 19 at device 0.1 on pci4 em1: Using an MSI interrupt em1: Ethernet address: 00:30:48:33:06:f3 pcib5: <ACPI PCI-PCI bridge> at device 0.3 on pci1 pci5: <ACPI PCI bus> on pcib5 mvs0: <Marvell 88SX6081 SATA controller> port 0x3000-0x30ff mem 0xd8200000-0xd82fffff irq 28 at device 2.0 on pci5 mvs0: Gen-II, 8 3Gbps ports, Port Multiplier supported mvsch0: <Marvell SATA channel> at channel 0 on mvs0 mvsch1: <Marvell SATA channel> at channel 1 on mvs0 mvsch2: <Marvell SATA channel> at channel 2 on mvs0 mvsch3: <Marvell SATA channel> at channel 3 on mvs0 mvsch4: <Marvell SATA channel> at channel 4 on mvs0 mvsch5: <Marvell SATA channel> at channel 5 on mvs0 mvsch6: <Marvell SATA channel> at channel 6 on mvs0 mvsch7: <Marvell SATA channel> at channel 7 on mvs0 pcib6: <ACPI PCI-PCI bridge> at device 4.0 on pci0 pci6: <ACPI PCI bus> on pcib6 pcib7: <ACPI PCI-PCI bridge> at device 6.0 on pci0 pci7: <ACPI PCI bus> on pcib7 pci0: <base peripheral> at device 8.0 (no driver attached) pcib8: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0 pci8: <ACPI PCI bus> on pcib8 pcib9: <PCI-PCI bridge> at device 0.0 on pci8 pci9: <PCI bus> on pcib9 pcib10: <PCI-PCI bridge> at device 0.0 on pci9 pci10: <PCI bus> on pcib10 em2: <Intel(R) PRO/1000 Network Connection 7.3.8> port 0x4000-0x401f mem 0xd8a20000-0xd8a3ffff,0xd8a00000-0xd8a1ffff irq 33 at device 0.0 on pci10 em2: Using an MSI interrupt em2: Ethernet address: 00:15:17:7c:bc:81 em3: <Intel(R) PRO/1000 Network Connection 7.3.8> port 0x4020-0x403f mem 0xd8a60000-0xd8a7ffff,0xd8a40000-0xd8a5ffff irq 32 at device 0.1 on pci10 em3: Using an MSI interrupt em3: Ethernet address: 00:15:17:7c:bc:80 pcib11: <PCI-PCI bridge> at device 1.0 on pci9 pci11: <PCI bus> on pcib11 em4: <Intel(R) PRO/1000 Network Connection 7.3.8> port 0x5000-0x501f mem 0xd8b20000-0xd8b3ffff,0xd8b00000-0xd8b1ffff irq 34 at device 0.0 on pci11 em4: Using an MSI interrupt em4: Ethernet address: 00:15:17:7c:bc:83 em5: <Intel(R) PRO/1000 Network Connection 7.3.8> port 0x5020-0x503f mem 0xd8b60000-0xd8b7ffff,0xd8b40000-0xd8b5ffff irq 33 at device 0.1 on pci11 em5: Using an MSI interrupt em5: Ethernet address: 00:15:17:7c:bc:82 uhci0: <Intel 631XESB/632XESB/3100 USB controller USB-1> port 0x1800-0x181f irq 17 at device 29.0 on pci0 usbus0 on uhci0 uhci1: <Intel 631XESB/632XESB/3100 USB controller USB-2> port 0x1820-0x183f irq 19 at device 29.1 on pci0 usbus1 on uhci1 uhci2: <Intel 631XESB/632XESB/3100 USB controller USB-3> port 0x1840-0x185f irq 18 at device 29.2 on pci0 usbus2 on uhci2 ehci0: <Intel 63XXESB USB 2.0 controller> mem 0xd8d00000-0xd8d003ff irq 17 at device 29.7 on pci0 usbus3: EHCI version 1.0 usbus3 on ehci0 pcib12: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci12: <ACPI PCI bus> on pcib12 vgapci0: <VGA-compatible display> port 0x6000-0x60ff mem 0xd0000000-0xd7ffffff,0xd8c00000-0xd8c0ffff irq 18 at device 1.0 on pci12 isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel 63XXESB2 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1860-0x186f at device 31.1 on pci0 ata0: <ATA channel> at channel 0 on atapci0 ahci0: <Intel ESB2 AHCI SATA controller> port 0x18a0-0x18a7,0x1874-0x1877,0x1878-0x187f,0x1870-0x1873,0x1880-0x189f mem 0xd8d00400-0xd8d007ff irq 19 at device 31.2 on pci0 ahci0: AHCI v1.10 with 6 3Gbps ports, Port Multiplier supported ahcich0: <AHCI channel> at channel 0 on ahci0 ahcich1: <AHCI channel> at channel 1 on ahci0 ahcich2: <AHCI channel> at channel 2 on ahci0 ahcich3: <AHCI channel> at channel 3 on ahci0 ahcich4: <AHCI channel> at channel 4 on ahci0 ahcich5: <AHCI channel> at channel 5 on ahci0 pci0: <serial bus, SMBus> at device 31.3 (no driver attached) acpi_button0: <Power Button> on acpi0 ipmi0: <IPMI System Interface> port 0xca2-0xca3 on acpi0 ipmi0: KCS mode found at io 0xca2 on acpi atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0 uart1: console (115200,n,8,1) fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 ichwd0 on isa0 wbwd0: <Winbond 83627HF/F/HG/G Rev. UD-A> at port 0x2e-0x2f on isa0 wbwd0: Before watchdog attach: Watchdog enabled. Scaling by 60s, timer at 5 (<=300s left). CRF5 0x08 CRF7 0xc0 ipmi1: <IPMI System Interface> on isa0 device_attach: ipmi1 attach returned 16 ipmi1: <IPMI System Interface> on isa0 device_attach: ipmi1 attach returned 16 orm0: <ISA Option ROM> at iomem 0xc0000-0xcafff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 coretemp0: <CPU On-Die Thermal Sensors> on cpu0 est0: <Enhanced SpeedStep Frequency Control> on cpu0 p4tcc0: <CPU Frequency Thermal Control> on cpu0 coretemp1: <CPU On-Die Thermal Sensors> on cpu1 est1: <Enhanced SpeedStep Frequency Control> on cpu1 p4tcc1: <CPU Frequency Thermal Control> on cpu1 coretemp2: <CPU On-Die Thermal Sensors> on cpu2 est2: <Enhanced SpeedStep Frequency Control> on cpu2 p4tcc2: <CPU Frequency Thermal Control> on cpu2 coretemp3: <CPU On-Die Thermal Sensors> on cpu3 est3: <Enhanced SpeedStep Frequency Control> on cpu3 p4tcc3: <CPU Frequency Thermal Control> on cpu3 coretemp4: <CPU On-Die Thermal Sensors> on cpu4 est4: <Enhanced SpeedStep Frequency Control> on cpu4 p4tcc4: <CPU Frequency Thermal Control> on cpu4 coretemp5: <CPU On-Die Thermal Sensors> on cpu5 est5: <Enhanced SpeedStep Frequency Control> on cpu5 p4tcc5: <CPU Frequency Thermal Control> on cpu5 coretemp6: <CPU On-Die Thermal Sensors> on cpu6 est6: <Enhanced SpeedStep Frequency Control> on cpu6 p4tcc6: <CPU Frequency Thermal Control> on cpu6 coretemp7: <CPU On-Die Thermal Sensors> on cpu7 est7: <Enhanced SpeedStep Frequency Control> on cpu7 p4tcc7: <CPU Frequency Thermal Control> on cpu7 Timecounters tick every 1.000 msec ipfw2 (+ipv6) initialized, divert enabled, nat enabled, default to accept, logging disabled DUMMYNET 0xfffffe000930edc0 with IPv6 initialized (100409) load_dn_sched dn_sched FIFO loaded load_dn_sched dn_sched PRIO loaded load_dn_sched dn_sched QFQ loaded load_dn_sched dn_sched RR loaded load_dn_sched dn_sched WF2Q+ loaded usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 ugen0.1: <Intel> at usbus0 uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <Intel> at usbus1 uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 ugen2.1: <Intel> at usbus2 uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 ugen3.1: <Intel> at usbus3 uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3 ipmi0: IPMI device rev. 1, firmware rev. 1.60, version 2.0 ipmi0: Number of channels 8 ipmi0: Attached watchdog ada0 at mvsch0 bus 0 scbus0 target 0 lun 0 ada0: <ST3000DM001-1CH166 CC29> ATA-9 SATA 3.x device ada0: Serial Number W1F4YELN ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 2048bytes) ada0: Command Queueing enabled ada0: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada0: quirks=0x1<4K> ada0: Previously was known as ad4 ada1 at mvsch1 bus 0 scbus1 target 0 lun 0 ada1: <ST3000DM001-1CH166 CC29> ATA-9 SATA 3.x device ada1: Serial Number W1F51E58 ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 2048bytes) ada1: Command Queueing enabled ada1: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada1: quirks=0x1<4K> ada1: Previously was known as ad6 ada2 at mvsch2 bus 0 scbus2 target 0 lun 0 ada2: <ST3000DM001-1CH166 CC29> ATA-9 SATA 3.x device ada2: Serial Number W1F509KF ada2: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 2048bytes) ada2: Command Queueing enabled ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada2: quirks=0x1<4K> ada2: Previously was known as ad8 ada3 at mvsch3 bus 0 scbus3 target 0 lun 0 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered ada3: <WDC WD30EZRX-00D8PB0 80.00A80> ATA-9 SATA 3.x device ada3: Serial Number WD-WCC4N0HT70SL ada3: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 2048bytes) ada3: Command Queueing enabled ada3: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada3: quirks=0x1<4K> ada3: Previously was known as ad10 ada4 at mvsch4 bus 0 scbus4 target 0 lun 0 ada4: <WDC WD30EZRX-00D8PB0 80.00A80> ATA-9 SATA 3.x device ada4: Serial Number WD-WCC4N5PRFUEL ada4: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 2048bytes) ada4: Command Queueing enabled ada4: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada4: quirks=0x1<4K> ada4: Previously was known as ad12 ada5 at mvsch5 bus 0 scbus5 target 0 lun 0 ada5: <WDC WD30EZRX-00D8PB0 80.00A80> ATA-9 SATA 3.x device ada5: Serial Number WD-WCC4N5PRFK1E ada5: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 2048bytes) ada5: Command Queueing enabled ada5: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada5: quirks=0x1<4K> ada5: Previously was known as ad14 ada6 at ahcich0 bus 0 scbus9 target 0 lun 0 ada6: <ST3000DM001-1CH166 CC27> ATA-9 SATA 3.x device ada6: Serial Number Z1F4111J ada6: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada6: Command Queueing enabled ada6: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada6: quirks=0x1<4K> ada6: Previously was known as ad20 ada7 at ahcich1 bus 0 scbus10 target 0 lun 0 ada7: <ST3000DM001-1CH166 CC27> ATA-9 SATA 3.x device ada7: Serial Number W1F3V65G ada7: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada7: Command Queueing enabled ada7: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada7: quirks=0x1<4K> ada7: Previously was known as ad22 ada8 at ahcich2 bus 0 scbus11 target 0 lun 0 ada8: <ST3000DM001-1CH166 CC26> ATA-8 SATA 3.x device ada8: Serial Number W1F2V6MA ada8: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada8: Command Queueing enabled ada8: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada8: quirks=0x1<4K> ada8: Previously was known as ad24 ada9 at ahcich3 bus 0 scbus12 target 0 lun 0 ada9: <ST3000DM001-1CH166 CC29> ATA-9 SATA 3.x device ada9: Serial Number W1F51ECL ada9: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada9: Command Queueing enabled ada9: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada9: quirks=0x1<4K> ada9: Previously was known as ad26 ada10 at ahcich4 bus 0 scbus13 target 0 lun 0 ada10: <ST3000DM001-1CH166 CC29> ATA-9 SATA 3.x device ada10: Serial Number Z1F55TKE ada10: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada10: Command Queueing enabled ada10: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada10: quirks=0x1<4K> ada10: Previously was known as ad28 ada11 at ahcich5 bus 0 scbus14 target 0 lun 0 ada11: <ST3000DM001-1CH166 CC29> ATA-9 SATA 3.x device ada11: Serial Number W1F51EFC ada11: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada11: Command Queueing enabled ada11: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada11: quirks=0x1<4K> ada11: Previously was known as ad30 SMP: AP CPU #7 Launched! SMP: AP CPU #1 Launched! SMP: AP CPU #2 Launched! SMP: AP CPU #3 Launched! SMP: AP CPU #6 Launched! SMP: AP CPU #4 Launched! SMP: AP CPU #5 Launched! uhub3: 6 ports with 6 removable, self powered (aprobe0:mvsch2:0:0:0): SETFEATURES SET TRANSFER MODE. ACB: ef 03 00 00 00 40 00 00 00 00 46 00 (aprobe0:mvsch2:0:0:0): CAM status: Unconditionally Re-queue Request (aprobe0:mvsch2:0:0:0): Error 5, Retry was blocked ugen3.2: <SanDisk> at usbus3 umass0: <SanDisk Cruzer Fit, class 0/0, rev 2.00/2.01, addr 2> on usbus3 umass0: SCSI over Bulk-Only; quirks = 0x0100 umass0:16:0:-1: Attached to scbus16 da0 at umass-sim0 bus 0 scbus16 target 0 lun 0 da0: <SanDisk Cruzer Fit 2.01> Fixed Direct Access SCSI-6 device da0: Serial Number 4C530301230125108365 da0: 40.000MB/s transfers da0: 3819MB (7821312 512 byte sectors: 255H 63S/T 486C) da0: quirks=0x2<NO_6_BYTE> ugen3.3: <Peppercon AG> at usbus3 uhid0: <Peppercon AG Multidevice, class 0/0, rev 2.00/0.01, addr 3> on usbus3 ukbd0: <Peppercon AG Multidevice, class 0/0, rev 2.00/0.01, addr 3> on usbus3 kbd2 at ukbd0 Trying to mount root from ufs:/dev/ufs/FreeNASs1a [ro]... (aprobe0:mvsch2:0:0:0): SETFEATURES SET TRANSFER MODE. ACB: ef 03 00 00 00 40 00 00 00 00 46 00 (aprobe0:mvsch2:0:0:0): CAM status: Unconditionally Re-queue Request (aprobe0:mvsch2:0:0:0): Error 5, Retry was blocked (aprobe1:mvsch2:0:15:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00 (aprobe1:mvsch2:0:15:0): CAM status: Unconditionally Re-queue Request (aprobe1:mvsch2:0:15:0): Error 5, Retry was blocked (aprobe0:mvsch2:0:0:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00 00 00 00 (aprobe0:mvsch2:0:0:0): CAM status: Unconditionally Re-queue Request (aprobe0:mvsch2:0:0:0): Error 5, Retry was blocked (aprobe0:mvsch2:0:0:0): SETFEATURES SET TRANSFER MODE. ACB: ef 03 00 00 00 40 00 00 00 00 46 00 (aprobe0:mvsch2:0:0:0): CAM status: Unconditionally Re-queue Request (aprobe0:mvsch2:0:0:0): Error 5, Retry was blocked (aprobe1:mvsch2:0:15:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00 (aprobe1:mvsch2:0:15:0): CAM status: Unconditionally Re-queue Request (aprobe1:mvsch2:0:15:0): Error 5, Retry was blocked (aprobe0:mvsch2:0:0:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00 00 00 00 (aprobe0:mvsch2:0:0:0): CAM status: Unconditionally Re-queue Request (aprobe0:mvsch2:0:0:0): Error 5, Retry was blocked (aprobe0:mvsch2:0:0:0): SETFEATURES SET TRANSFER MODE. ACB: ef 03 00 00 00 40 00 00 00 00 46 00 (aprobe0:mvsch2:0:0:0): CAM status: Unconditionally Re-queue Request (aprobe0:mvsch2:0:0:0): Error 5, Retry was blocked (aprobe1:mvsch2:0:15:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00 (aprobe1:mvsch2:0:15:0): CAM status: Unconditionally Re-queue Request (aprobe1:mvsch2:0:15:0): Error 5, Retry was blocked (aprobe0:mvsch2:0:0:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00 00 00 00 (aprobe0:mvsch2:0:0:0): CAM status: Unconditionally Re-queue Request (aprobe0:mvsch2:0:0:0): Error 5, Retry was blocked (aprobe0:mvsch2:0:0:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00 00 00 00 (aprobe0:mvsch2:0:0:0): CAM status: Unconditionally Re-queue Request (aprobe0:mvsch2:0:0:0): Error 5, Retry was blocked (aprobe1:mvsch2:0:15:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00 (aprobe1:mvsch2:0:15:0): CAM status: Unconditionally Re-queue Request (aprobe1:mvsch2:0:15:0): Error 5, Retry was blocked (aprobe0:mvsch2:0:0:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00 00 00 00 (aprobe0:mvsch2:0:0:0): CAM status: Unconditionally Re-queue Request (aprobe0:mvsch2:0:0:0): Error 5, Retry was blocked (aprobe0:mvsch2:0:0:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00 00 00 00 (aprobe0:mvsch2:0:0:0): CAM status: Unconditionally Re-queue Request (aprobe0:mvsch2:0:0:0): Error 5, Retry was blocked (aprobe0:mvsch2:0:0:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00 00 00 00 (aprobe0:mvsch2:0:0:0): CAM status: Unconditionally Re-queue Request (aprobe0:mvsch2:0:0:0): Error 5, Retry was blocked GEOM_RAID5: Module loaded, version 1.1.20130907.44 (rev 5c6d2a159411) ZFS filesystem version: 5 ZFS storage pool version: features support (5000) GEOM_ELI: Device ada8p1.eli created. GEOM_ELI: Encryption: AES-XTS 256 GEOM_ELI: Crypto: software GEOM_ELI: Device ada7p1.eli created. GEOM_ELI: Encryption: AES-XTS 256 GEOM_ELI: Crypto: software GEOM_ELI: Device ada6p1.eli created. GEOM_ELI: Encryption: AES-XTS 256 GEOM_ELI: Crypto: software GEOM_ELI: Device ada2p1.eli created. GEOM_ELI: Encryption: AES-XTS 256 GEOM_ELI: Crypto: software GEOM_ELI: Device ada1p1.eli created. GEOM_ELI: Encryption: AES-XTS 256 GEOM_ELI: Crypto: software GEOM_ELI: Device ada0p1.eli created. GEOM_ELI: Encryption: AES-XTS 256 GEOM_ELI: Crypto: software GEOM_ELI: Device ada9p1.eli created. GEOM_ELI: Encryption: AES-XTS 256 GEOM_ELI: Crypto: software
How can I tell what device it is talking about?