Yesterday I upgraded to FreeNAS 11.1 (from 9.10u6).
Most things work fine, except the network in iohyve. Jails on the same bridge work well.
Even though some iohyve VM network functions seem to work - the VM has an IP address, the route is good, ping works - I cannot transfer data in and out the VM. Most obvious is that when I make an ftp connection, I can log in, change directory but not transfer data.
Because 5 iohyve VMs do not work anymore I suspect the bridge is the issue.
Even after a rollback to 9.10 is does not work anymore.
Who can help with finding the issue?
Should the bridge have an IP address?
Do you advise to try to fix it in 9.10 or 11.1 (e.g. using the new VM's in 11.1).
Bridge configuration
Configuration of one of the iohyve VMs (related to tap7 in the bridge)
Most things work fine, except the network in iohyve. Jails on the same bridge work well.
Even though some iohyve VM network functions seem to work - the VM has an IP address, the route is good, ping works - I cannot transfer data in and out the VM. Most obvious is that when I make an ftp connection, I can log in, change directory but not transfer data.
Because 5 iohyve VMs do not work anymore I suspect the bridge is the issue.
Even after a rollback to 9.10 is does not work anymore.
Who can help with finding the issue?
Should the bridge have an IP address?
Do you advise to try to fix it in 9.10 or 11.1 (e.g. using the new VM's in 11.1).
Bridge configuration
Code:
bridge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 description: iohyve-bridge ether 02:77:13:69:62:00 nd6 options=1<PERFORMNUD> id 00:00:00:00:00:00 priority 32768 hellotime 2 fwddelay 15 maxage 20 holdcnt 6 proto rstp maxaddr 2000 timeout 1200 root id 00:00:00:00:00:00 priority 32768 ifcost 0 port 0 member: epair6a flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP> ifmaxaddr 0 port 16 priority 128 path cost 2000 member: epair5a flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP> ifmaxaddr 0 port 15 priority 128 path cost 2000 member: epair4a flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP> ifmaxaddr 0 port 14 priority 128 path cost 2000 member: epair3a flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP> ifmaxaddr 0 port 13 priority 128 path cost 2000 member: epair2a flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP> ifmaxaddr 0 port 12 priority 128 path cost 2000 member: epair1a flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP> ifmaxaddr 0 port 11 priority 128 path cost 2000 member: epair0a flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP> ifmaxaddr 0 port 10 priority 128 path cost 2000 member: tap5 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP> ifmaxaddr 0 port 9 priority 128 path cost 2000000 member: tap10 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP> ifmaxaddr 0 port 8 priority 128 path cost 2000000 member: tap12 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP> ifmaxaddr 0 port 7 priority 128 path cost 2000000 member: tap9 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP> ifmaxaddr 0 port 6 priority 128 path cost 2000000 member: tap7 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP> ifmaxaddr 0 port 5 priority 128 path cost 2000000 member: ix0 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP> ifmaxaddr 0 port 1 priority 128 path cost 2000
Configuration of one of the iohyve VMs (related to tap7 in the bridge)
Code:
eth0 Link encap:Ethernet HWaddr 00:a0:98:32:81:d8 inet addr:192.168.178.219 Bcast:192.168.178.255 Mask:255.255.255.0 inet6 addr: fe80::2a0:98ff:fe32:81d8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1464 Metric:1 RX packets:168455 errors:0 dropped:472 overruns:0 frame:0 TX packets:37403 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:23746094 (22.6 MiB) TX bytes:2503402 (2.3 MiB)
Last edited: