12pharoh21
Dabbler
- Joined
- Jun 7, 2016
- Messages
- 15
Hello all,
I am not new to TrueNAS/FreeNAS and have another server that I have been running for several years. Getting this new server setup has been a challenge so far though. My first server started on FreeNAS 9 (if I remember correct, might have been 8), and has been upgraded and is now running TrueNAS-12.0-U6.
I have done a ton of searching and can't really find anything like what I'm seeing. I am having a two fold problem with my TrueNAS install. This is a brand new setup that I am just getting started. Here is my server config:
TrueNAS-12.0-U7
MB - ASUS SaberTooth X58
CPU - Intel(R) Core(TM) i7 CPU 950 @ 3.07GHz
RAM - 24GB
LSI MegaRAID SAS 9361-4i
LSI LSI00412 0.6 Meter Internal Cable SFF8643 to x4 SAS8482
-Disks - 4x8TB HGST SAS NAS drives in RAIDZ1
The first part of this is I was able to get the TrueNAS server setup fine, but when I rebooted the machine it goes through a process of doing disk reads from sectors and took almost 2 hours to complete. If I power off the server and disconnect the SAS cable from the LSI card then boot it goes right into the TrueNAS GUI on the console. With the cable connected it does the read from sectors thing. (I can get an output of this data, but want to follow up on the second part first before I reboot again)
I let that complete and was able to get into the GUI using the IP address so I could start the configration, but as soon as I add the pool to the config in TrueNAS the console continually shows the following
At first I thought it was doing a scrub of the pool, but it's been running for almost 24 hours at this point and everything in the GUI is showing stable and OK. I have not rebooted the server since I added the pool and it started doing this because I wanted to see if it would stop on it's own.
Also of note, I can modify the configuration of the TrueNAS server without issue, I have been able to add a dataset to the pool and was able to add an SMB share to that as well as an NFS share. There are some issues with NFS share, but I will probably start a new thread for that one once this is resolved. Let me know if you need any other info from my system or if you have suggestions on what to try next. Thanks in advance for your help.
I am not new to TrueNAS/FreeNAS and have another server that I have been running for several years. Getting this new server setup has been a challenge so far though. My first server started on FreeNAS 9 (if I remember correct, might have been 8), and has been upgraded and is now running TrueNAS-12.0-U6.
I have done a ton of searching and can't really find anything like what I'm seeing. I am having a two fold problem with my TrueNAS install. This is a brand new setup that I am just getting started. Here is my server config:
TrueNAS-12.0-U7
MB - ASUS SaberTooth X58
CPU - Intel(R) Core(TM) i7 CPU 950 @ 3.07GHz
RAM - 24GB
LSI MegaRAID SAS 9361-4i
LSI LSI00412 0.6 Meter Internal Cable SFF8643 to x4 SAS8482
-Disks - 4x8TB HGST SAS NAS drives in RAIDZ1
The first part of this is I was able to get the TrueNAS server setup fine, but when I rebooted the machine it goes through a process of doing disk reads from sectors and took almost 2 hours to complete. If I power off the server and disconnect the SAS cable from the LSI card then boot it goes right into the TrueNAS GUI on the console. With the cable connected it does the read from sectors thing. (I can get an output of this data, but want to follow up on the second part first before I reboot again)
I let that complete and was able to get into the GUI using the IP address so I could start the configration, but as soon as I add the pool to the config in TrueNAS the console continually shows the following
Code:
(da2:mrsas0:1:10:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00 (da2:mrsas0:1:10:0): CAM status: SCSI Status Error (da2:mrsas0:1:10:0): SCSI status: OK (da2:mrsas0:1:10:0): WRITE(10). CDB: 2a 00 00 41 76 d0 00 00 08 00 (da2:mrsas0:1:10:0): CAM status: SCSI Status Error (da2:mrsas0:1:10:0): SCSI status: OK (da1:mrsas0:1:9:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00 (da1:mrsas0:1:9:0): CAM status: SCSI Status Error (da1:mrsas0:1:9:0): SCSI status: OK (da2:mrsas0:1:10:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00 (da2:mrsas0:1:10:0): CAM status: SCSI Status Error (da2:mrsas0:1:10:0): SCSI status: OK (da2:mrsas0:1:10:0): WRITE(10). CDB: 2a 00 00 40 02 18 00 00 08 00 (da2:mrsas0:1:10:0): CAM status: SCSI Status Error (da2:mrsas0:1:10:0): SCSI status: OK (da1:mrsas0:1:9:0): WRITE(10). CDB: 2a 00 00 40 02 18 00 00 08 00 (da1:mrsas0:1:9:0): CAM status: SCSI Status Error (da1:mrsas0:1:9:0): SCSI status: OK (da1:mrsas0:1:9:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00 (da1:mrsas0:1:9:0): CAM status: SCSI Status Error (da1:mrsas0:1:9:0): SCSI status: OK (da1:mrsas0:1:9:0): WRITE(10). CDB: 2a 00 00 c1 4b 58 00 00 08 00 (da1:mrsas0:1:9:0): CAM status: SCSI Status Error (da1:mrsas0:1:9:0): SCSI status: OK (da3:mrsas0:1:11:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00 (da3:mrsas0:1:11:0): CAM status: SCSI Status Error (da3:mrsas0:1:11:0): SCSI status: OK (da3:mrsas0:1:11:0): WRITE(10). CDB: 2a 00 00 40 02 28 00 00 08 00 (da3:mrsas0:1:11:0): CAM status: SCSI Status Error (da3:mrsas0:1:11:0): SCSI status: OK (da0:mrsas0:1:8:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00 (da0:mrsas0:1:8:0): CAM status: SCSI Status Error (da0:mrsas0:1:8:0): SCSI status: OK (da0:mrsas0:1:8:0): WRITE(10). CDB: 2a 00 00 40 02 38 00 00 08 00 (da0:mrsas0:1:8:0): CAM status: SCSI Status Error (da0:mrsas0:1:8:0): SCSI status: OK (da0:mrsas0:1:8:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00 (da0:mrsas0:1:8:0): CAM status: SCSI Status Error (da0:mrsas0:1:8:0): SCSI status: OK (da0:mrsas0:1:8:0): WRITE(10). CDB: 2a 00 00 41 78 48 00 00 08 00 (da0:mrsas0:1:8:0): CAM status: SCSI Status Error (da0:mrsas0:1:8:0): SCSI status: OK (da3:mrsas0:1:11:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00 (da3:mrsas0:1:11:0): CAM status: SCSI Status Error (da3:mrsas0:1:11:0): SCSI status: OK (da0:mrsas0:1:8:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00 (da0:mrsas0:1:8:0): CAM status: SCSI Status Error (da0:mrsas0:1:8:0): SCSI status: OK (da3:mrsas0:1:11:0): WRITE(10). CDB: 2a 00 00 40 02 40 00 00 08 00 (da3:mrsas0:1:11:0): CAM status: SCSI Status Error (da3:mrsas0:1:11:0): SCSI status: OK (da0:mrsas0:1:8:0): WRITE(10). CDB: 2a 00 00 40 02 40 00 00 08 00 (da0:mrsas0:1:8:0): CAM status: SCSI Status Error (da0:mrsas0:1:8:0): SCSI status: OK (da0:mrsas0:1:8:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00 (da0:mrsas0:1:8:0): CAM status: SCSI Status Error (da0:mrsas0:1:8:0): SCSI status: OK (da0:mrsas0:1:8:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00 (da0:mrsas0:1:8:0): CAM status: SCSI Status Error (da0:mrsas0:1:8:0): SCSI status: OK (da0:mrsas0:1:8:0): WRITE(10). CDB: 2a 00 00 40 01 b8 00 00 08 00 (da0:mrsas0:1:8:0): CAM status: SCSI Status Error (da0:mrsas0:1:8:0): SCSI status: OK (da0:mrsas0:1:8:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00 (da0:mrsas0:1:8:0): CAM status: SCSI Status Error (da0:mrsas0:1:8:0): SCSI status: OK (da0:mrsas0:1:8:0): WRITE(10). CDB: 2a 00 00 41 79 60 00 00 08 00 (da0:mrsas0:1:8:0): CAM status: SCSI Status Error (da0:mrsas0:1:8:0): SCSI status: OK
At first I thought it was doing a scrub of the pool, but it's been running for almost 24 hours at this point and everything in the GUI is showing stable and OK. I have not rebooted the server since I added the pool and it started doing this because I wanted to see if it would stop on it's own.
Also of note, I can modify the configuration of the TrueNAS server without issue, I have been able to add a dataset to the pool and was able to add an SMB share to that as well as an NFS share. There are some issues with NFS share, but I will probably start a new thread for that one once this is resolved. Let me know if you need any other info from my system or if you have suggestions on what to try next. Thanks in advance for your help.