Xilinx ethernet device problem

[vfmsuluhantr]

Hello

I installed FreeNAS into my old server.
FreeNAS release information as follows
9.3-RELEASE-p13 FreeBSD 9.3-RELEASE-p13 #3 r281084+fbfa186: Thu Apr 9 19:18:25 PDT 2015 root@build3.ixsystems.com:/tank/home/jkh/build/FN/objs/os-base/amd64/tank/home/jkh/build/FN/FreeBSD/src/sys/FREENAS.amd64 amd64

As far as I could see, FreeNAS could not recognize one of the ethernet device

from dmesg.boot

pci2: <ACPI PCI bus> on pcib2
pci2: <network, ethernet> at device 0.0 (no driver attached)​

from lspci -vv

02:00.0 Ethernet controller: Xilinx Corporation Default PCIe endpoint ID
Subsystem: Xilinx Corporation Default PCIe endpoint ID
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 24
Region 0: Memory at b1b00000 (64-bit, non-prefetchable)
Expansion ROM at fff00000 [disabled]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [60] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 1, Latency L0s unlimited, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Exit Latency L0s unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
​

I have 2 Intel ethernet devices, loopback device and ipfw0 device on ifconfig output. So How can I enable Xilinx Ethernet on my server ?

Thanks

 

[SweetAndLow]

Get an Intel pro PCI based Ethernet card. Yours probably isn't supported

 

[Whattteva]

I didn't know Xilinx makes Ethernet controllers for non FPGA boards. I guess you learn something new everyday.

 

[vfmsuluhantr]

thanks for your reply
actually I am using old telecomm specific server as freenas server.
there are some specific cards on it, anyway I will cont. with onboard 1 GB for startup