View Disks: "No entry has been found"

[mdrisser]

If I go to Storage > Volumes > View Disks all I get is "No entry has been found". I have zpools and zvols created using these disks, but nothing shows in the WebGUI. Searching through the documentation and the forums has revealed no solution to this problem, and all of the entries are several years old.

 

[Ericloewe]

Works fine for me... Can you run Verify Install and report back?

 

[mdrisser]

What is Verify Install? (Edit: Nevermind, found the Verify Install button) The systems were set up by IXSystems. I did run the upgrade to 9.10 STABLE, but I don't know if they were visible in View Disks prior to that.

 

[mdrisser]

We have two FreeNAS boxes, both of which were originally set up by IXSystems. Both have been updated to 9.10 STABLE using the web interface. Neither one is showing any entries under View Disks.

I ran the verify install on both of the boxes we have. Both came back with:

The following Inconsistencies were found in your Current Install:
List of Checksum Mismatches:
/boot/loader.conf

List of Files/Directories/Symlinks not Found:
/compat/linux/proc/.donotremove

List of Permission Errors:
/compat/linux/proc Expected MODE: 0755, Got: 0555

 

[Ericloewe]

List of Checksum Mismatches:
/boot/loader.conf

That looks dubious.

List of Files/Directories/Symlinks not Found:
/compat/linux/proc/.donotremove

Same.

List of Permission Errors:
/compat/linux/proc Expected MODE: 0755, Got: 0555

I think that's just a bug, nothing to worry about.

I'd try reinstalling FreeNAS. Be sure to save a copy of the config file, so that you don't have to reconfigure from scratch.

 

[joeschmuck]

If iXsystems did the installation, I take it you don't have some maintenance contract with them?

Also, lets try to clear the air just a bit here and figure out exactly what is going on.

1) List your hardware.
2) Which version of FreeNAS are you using?
3) Was this working before the upgrade or did it stop working before that?
4) Is the FreeNAS OS on a USB Flash drive? If yes, I'd replace it with a new one when you reinstall FreeNAS and leave the original one in-tact.
5) How are the hard drives connected to the system? Directly to the motherboard or to an add-on card?
6) Are the hard drives spinning?
7) Post the output of "dmesg" in code tags (listing).

 

[mdrisser]

@joeschmuck:
No, we only have a maintenance contract on the hardware we purchased from them.
1) The hardware for both boxes:
Intel Xeon E5-2609v2 @ 2.50GHz
34GB RAM
Intel Pro/1000 Quad-port NIC
8X HGST 8TB HDD

2) FreeNAS-9.10.1.U1 (ff51a5d)

3) I don't know if this was working before the upgrade or not

4) The OS is not on a flash drive, it looks like it is on a 30GB partition

5) Harddrives appear to be on a daughter board, these are SuperMicro boxes

6) Yes, the harddrives are spinning, in fact I have zvols and and datasets running on the drives; periodic snapshots are running, and replication between the two boxes is working as well.

7) I'll post the dmesg output later as I am not currently on a machine with access to the FreeNAS boxes

@Ericloewe: I'm not exactly fond of the idea of re-installing the OS on production boxes, unless of course that is the ONLY recourse.

 

[mdrisser]

Output from dmesg:

Code:

Copyright (c) 1992-2016 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
		The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.3-STABLE #0 r295946+9bbba48(9.10-STABLE): Mon Sep 26 21:03:32 UTC 2016
	root@gauntlet:/freenas-9.10-releng/_BE/objs/freenas-9.10-releng/_BE/os/sys/FreeNAS.amd64 amd64
FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
CPU: Intel(R) Xeon(R) CPU E5-2609 v2 @ 2.50GHz (2500.05-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0x306e4  Family=0x6  Model=0x3e  Stepping=4
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x7fbee3ff<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,DCA,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,AESNI,XSAVE,OSXSAVE,AVX,F16C,RDRAND>
  AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM>
  AMD Features2=0x1<LAHF>
  Structured Extended Features=0x281<FSGSBASE,SMEP,ERMS>
  XSAVE Features=0x1<XSAVEOPT>
  VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID,VID,PostIntr
  TSC: P-state invariant, performance statistics
real memory  = 36507222016 (34816 MB)
avail memory = 33207652352 (31669 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <ALASKA A M I>
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
FreeBSD/SMP: 2 package(s) x 4 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  2
 cpu2 (AP): APIC ID:  4
 cpu3 (AP): APIC ID:  6
 cpu4 (AP): APIC ID: 32
 cpu5 (AP): APIC ID: 34
 cpu6 (AP): APIC ID: 36
 cpu7 (AP): APIC ID: 38
random: <Software, Yarrow> initialized
WARNING: VIMAGE (virtualized network stack) is a highly experimental feature.
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 24-47 on motherboard
ioapic2 <Version 2.0> irqs 48-71 on motherboard
kbd1 at kbdmux0
aesni0: <AES-CBC,AES-XTS> on motherboard
padlock0: No ACE support.
cryptosoft0: <software crypto> on motherboard
acpi0: <ALASKA A M I> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
cpu4: <ACPI CPU> on acpi0
cpu5: <ACPI CPU> on acpi0
cpu6: <ACPI CPU> on acpi0
cpu7: <ACPI CPU> on acpi0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 550
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 26 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
mps0: <Avago Technologies (LSI) SAS2308> port 0x8000-0x80ff mem 0xdfa40000-0xdfa4ffff,0xdfa00000-0xdfa3ffff irq 16 at device 0.0 on pci1
mps0: Firmware: 20.00.04.00, Driver: 21.00.00.00-fbsd
mps0: IOCCapabilities: 4185c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,IR>
pcib2: <ACPI PCI-PCI bridge> irq 32 at device 2.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 32 at device 2.2 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 40 at device 3.0 on pci0
pci4: <ACPI PCI bus> on pcib4
igb0: <Intel(R) PRO/1000 Network Connection, Version - 2.5.3-k> port 0x7060-0x707f mem 0xdfc60000-0xdfc7ffff,0xdfc8c000-0xdfc8ffff irq 40 at device 0.0 on pci4
igb0: Using MSIX interrupts with 9 vectors
igb0: Ethernet address: 0c:c4:7a:54:1e:98
igb0: Bound queue 0 to cpu 0
igb0: Bound queue 1 to cpu 1
igb0: Bound queue 2 to cpu 2
igb0: Bound queue 3 to cpu 3
igb0: Bound queue 4 to cpu 4
igb0: Bound queue 5 to cpu 5
igb0: Bound queue 6 to cpu 6
igb0: Bound queue 7 to cpu 7
igb1: <Intel(R) PRO/1000 Network Connection, Version - 2.5.3-k> port 0x7040-0x705f mem 0xdfc40000-0xdfc5ffff,0xdfc88000-0xdfc8bfff irq 44 at device 0.1 on pci4
igb1: Using MSIX interrupts with 9 vectors
igb1: Ethernet address: 0c:c4:7a:54:1e:99
igb1: Bound queue 0 to cpu 0
igb1: Bound queue 1 to cpu 1
igb1: Bound queue 2 to cpu 2
igb1: Bound queue 3 to cpu 3
igb1: Bound queue 4 to cpu 4
igb1: Bound queue 5 to cpu 5
igb1: Bound queue 6 to cpu 6
igb1: Bound queue 7 to cpu 7
igb2: <Intel(R) PRO/1000 Network Connection, Version - 2.5.3-k> port 0x7020-0x703f mem 0xdfc20000-0xdfc3ffff,0xdfc84000-0xdfc87fff irq 45 at device 0.2 on pci4
igb2: Using MSIX interrupts with 9 vectors
igb2: Ethernet address: 0c:c4:7a:54:1e:9a
igb2: Bound queue 0 to cpu 0
igb2: Bound queue 1 to cpu 1
igb2: Bound queue 2 to cpu 2
igb2: Bound queue 3 to cpu 3
igb2: Bound queue 4 to cpu 4
igb2: Bound queue 5 to cpu 5
igb2: Bound queue 6 to cpu 6
igb2: Bound queue 7 to cpu 7
igb3: <Intel(R) PRO/1000 Network Connection, Version - 2.5.3-k> port 0x7000-0x701f mem 0xdfc00000-0xdfc1ffff,0xdfc80000-0xdfc83fff irq 46 at device 0.3 on pci4
igb3: Using MSIX interrupts with 9 vectors
igb3: Ethernet address: 0c:c4:7a:54:1e:9b
igb3: Bound queue 0 to cpu 0
igb3: Bound queue 1 to cpu 1
igb3: Bound queue 2 to cpu 2
igb3: Bound queue 3 to cpu 3
igb3: Bound queue 4 to cpu 4
igb3: Bound queue 5 to cpu 5
igb3: Bound queue 6 to cpu 6
igb3: Bound queue 7 to cpu 7
pcib5: <ACPI PCI-PCI bridge> irq 40 at device 3.2 on pci0
pci6: <ACPI PCI bus> on pcib5
pcib6: <ACPI PCI-PCI bridge> irq 16 at device 17.0 on pci0
pci7: <ACPI PCI bus> on pcib6
isci0: <Intel(R) C600 Series Chipset SAS Controller (SATA mode)> port 0x6000-0x60ff mem 0xde47c000-0xde47ffff,0xde000000-0xde3fffff irq 16 at device 0.0 on pci7
pci0: <simple comms> at device 22.0 (no driver attached)
pci0: <simple comms> at device 22.1 (no driver attached)
ehci0: <Intel Patsburg USB 2.0 controller> mem 0xdfd24000-0xdfd243ff irq 16 at device 26.0 on pci0
usbus0: EHCI version 1.0
usbus0 on ehci0
ehci1: <Intel Patsburg USB 2.0 controller> mem 0xdfd23000-0xdfd233ff irq 23 at device 29.0 on pci0
usbus1: EHCI version 1.0
usbus1 on ehci1
pcib7: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci8: <ACPI PCI bus> on pcib7
vgapci0: <VGA-compatible display> mem 0xdd000000-0xddffffff,0xdf800000-0xdf803fff,0xdf000000-0xdf7fffff irq 16 at device 3.0 on pci8
vgapci0: Boot video device
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
ahci0: <Intel Patsburg AHCI SATA controller> port 0x9070-0x9077,0x9060-0x9063,0x9050-0x9057,0x9040-0x9043,0x9020-0x903f mem 0xdfd22000-0xdfd227ff irq 19 at device 31.2 on pci0
ahci0: AHCI v1.30 with 6 6Gbps ports, Port Multiplier not supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich3: <AHCI channel> at channel 3 on ahci0
ahcich4: <AHCI channel> at channel 4 on ahci0
ahcich5: <AHCI channel> at channel 5 on ahci0
pcib8: <ACPI Host-PCI bridge> on acpi0
pci127: <ACPI PCI bus> on pcib8
pcib9: <ACPI Host-PCI bridge> on acpi0
pci128: <ACPI PCI bus> on pcib9
pcib10: <ACPI PCI-PCI bridge> irq 50 at device 1.0 on pci128
pci129: <ACPI PCI bus> on pcib10
pcib11: <ACPI PCI-PCI bridge> irq 56 at device 2.0 on pci128
pci130: <ACPI PCI bus> on pcib11
pcib12: <ACPI PCI-PCI bridge> irq 64 at device 3.0 on pci128
pci131: <ACPI PCI bus> on pcib12
pcib13: <ACPI Host-PCI bridge> on acpi0
pci255: <ACPI PCI bus> on pcib13
acpi_button0: <Power Button> on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
ichwd0: <Intel Patsburg watchdog timer> on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc87ff,0xc8800-0xc97ff,0xc9800-0xc9fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
est1: <Enhanced SpeedStep Frequency Control> on cpu1
coretemp2: <CPU On-Die Thermal Sensors> on cpu2
est2: <Enhanced SpeedStep Frequency Control> on cpu2
coretemp3: <CPU On-Die Thermal Sensors> on cpu3
est3: <Enhanced SpeedStep Frequency Control> on cpu3
coretemp4: <CPU On-Die Thermal Sensors> on cpu4
est4: <Enhanced SpeedStep Frequency Control> on cpu4
coretemp5: <CPU On-Die Thermal Sensors> on cpu5
est5: <Enhanced SpeedStep Frequency Control> on cpu5
coretemp6: <CPU On-Die Thermal Sensors> on cpu6
est6: <Enhanced SpeedStep Frequency Control> on cpu6
coretemp7: <CPU On-Die Thermal Sensors> on cpu7
est7: <Enhanced SpeedStep Frequency Control> on cpu7
random: unblocking device.
usbus0: 480Mbps High Speed USB v2.0
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
Timecounters tick every 1.000 msec
ipfw2 (+ipv6) initialized, divert enabled, nat enabled, default to accept, logging disabled
DUMMYNET 0xfffff800075355c0 with IPv6 initialized (100409)
load_dn_aqm dn_aqm CODEL loaded
load_dn_aqm dn_aqm PIE loaded
load_dn_sched dn_sched FIFO loaded
load_dn_sched dn_sched QFQ loaded
load_dn_sched dn_sched RR loaded
load_dn_sched dn_sched WF2Q+ loaded
load_dn_sched dn_sched PRIO loaded
load_dn_sched dn_sched FQ_CODEL loaded
load_dn_sched dn_sched FQ_PIE loaded
usbus1: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
ugen0.2: <vendor 0x8087> at usbus0
uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus0
ugen1.2: <vendor 0x8087> at usbus1
uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus1
uhub2: 6 ports with 6 removable, self powered
uhub3: 8 ports with 8 removable, self powered
ugen0.3: <Winbond Electronics Corp> at usbus0
ukbd0: <Winbond Electronics Corp Hermon USB hidmouse Device, class 0/0, rev 1.10/0.01, addr 3> on usbus0
kbd0 at ukbd0
ses0 at mps0 bus 0 scbus0 target 20 lun 0
ses0: <LSI SAS2X36 0e12> Fixed Enclosure Services SPC-3 SCSI device
ses0: Serial Number 
ses0: 600.000MB/s transfers
ses0: Command Queueing enabled
ses0: SCSI-3 ENC Device
ses1 at mps0 bus 0 scbus0 target 31 lun 0
ses1: <LSI SAS2X36 0e12> Fixed Enclosure Services SPC-3 SCSI device
ses1: Serial Number 
ses1: 600.000MB/s transfers
ses1: Command Queueing enabled
ses1: SCSI-3 ENC Device
da2 at mps0 bus 0 scbus0 target 12 lun 0
da2: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da12 at mps0 bus 0 scbus0 target 23 lun 0
da12: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da2: Serial Number		 VKGTTA5X
da2: 600.000MB/s transfers
da12: Serial Number		 VKGTTA5X
da12: 600.000MB/s transfers
da2: Command Queueing enabled
da2: 7630885MB (1953506646 4096 byte sectors)
da8 at mps0 bus 0 scbus0 target 18 lun 0
da12: Command Queueing enabled
da12: 7630885MB (1953506646 4096 byte sectors)
da8: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da8: Serial Number		 VKH5ENYX
da3 at mps0 bus 0 scbus0 target 13 lun 0
da3: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da8: 600.000MB/s transfers
da3: Serial Number		 VKH4R0LX
da8: Command Queueing enabled
da3: 600.000MB/s transfers
da8: 7630885MB (1953506646 4096 byte sectors)
da3: Command Queueing enabled
da3: 7630885MB (1953506646 4096 byte sectors)
da13 at mps0 bus 0 scbus0 target 24 lun 0
da13: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da9 at mps0 bus 0 scbus0 target 19 lun 0
da9: <HGST HUH728080AL4200 A907> Fixed Direct Access SPC-4 SCSI device
da13: Serial Number		 VKH4R0LX
da13: 600.000MB/s transfers
da9: Serial Number		 VLG28DDV
da9: 600.000MB/s transfers
da9: Command Queueing enabled
da13: Command Queueing enabled
da13: 7630885MB (1953506646 4096 byte sectors)
da9: 7630885MB (1953506646 4096 byte sectors)
da6 at mps0 bus 0 scbus0 target 16 lun 0
da16 at mps0 bus 0 scbus0 target 27 lun 0
da6: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da16: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da16: Serial Number		 VKGZTKXX
da6: Serial Number		 VKGZTKXX
da6: 600.000MB/s transfers
da6: Command Queueing enabled
da16: 600.000MB/s transfers
da16: Command Queueing enabled
da6: 7630885MB (1953506646 4096 byte sectors)
da16: 7630885MB (1953506646 4096 byte sectors)
da0 at mps0 bus 0 scbus0 target 10 lun 0
da18 at mps0 bus 0 scbus0 target 29 lun 0
da18: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da0: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da0: Serial Number		 VKH3LEEX
da18: Serial Number		 VKH5ENYX
da18: 600.000MB/s transfers
da0: 600.000MB/s transfers
da0: Command Queueing enabled
da18: Command Queueing enabled
da0: 7630885MB (1953506646 4096 byte sectors)
da19 at mps0 bus 0 scbus0 target 30 lun 0
da18: 7630885MB (1953506646 4096 byte sectors)
da10 at mps0 bus 0 scbus0 target 21 lun 0
da19: <HGST HUH728080AL4200 A907> Fixed Direct Access SPC-4 SCSI device
da19: Serial Number		 VLG28DDV
da10: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da10: Serial Number		 VKH3LEEX
da10: 600.000MB/s transfersda19: 600.000MB/s transfers
da19: Command Queueing enabled
da19: 7630885MB (1953506646 4096 byte sectors)

da10: Command Queueing enabled
da17 at mps0 bus 0 scbus0 target 28 lun 0
da17: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da17: Serial Number		 VKH36RYX
da10: 7630885MB (1953506646 4096 byte sectors)
da7 at mps0 bus 0 scbus0 target 17 lun 0
da17: 600.000MB/s transfers
da17: Command Queueing enabled
da7: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da7: Serial Number		 VKH36RYX
da17: 7630885MB (1953506646 4096 byte sectors)
da15 at mps0 bus 0 scbus0 target 26 lun 0
da7: 600.000MB/s transfersda15: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da15: Serial Number		 VKH48NUX

da7: Command Queueing enabled
da7: 7630885MB (1953506646 4096 byte sectors)
da15: 600.000MB/s transfers
da15: Command Queueing enabled
da5 at mps0 bus 0 scbus0 target 15 lun 0
da5: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da15: 7630885MB (1953506646 4096 byte sectors)
da4 at mps0 bus 0 scbus0 target 14 lun 0
da5: Serial Number		 VKH48NUX
da5: 600.000MB/s transfers
da5: Command Queueing enabled
da4: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da4: Serial Number		 VKH4UGKX
da5: 7630885MB (1953506646 4096 byte sectors)
da4: 600.000MB/s transfers
da14 at mps0 bus 0 scbus0 target 25 lun 0
da14: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da4: Command Queueing enabled
da4: 7630885MB (1953506646 4096 byte sectors)
da11 at mps0 bus 0 scbus0 target 22 lun 0
da14: Serial Number		 VKH4UGKX
da14: 600.000MB/s transfers
da11: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da11: Serial Number		 VKGWDP3X
da14: Command Queueing enabled
da14: 7630885MB (1953506646 4096 byte sectors)
da1 at mps0 bus 0 scbus0 target 11 lun 0
da11: 600.000MB/s transfers
da11: Command Queueing enabled
da1: <HGST HUH728080AL4200 A7J0> Fixed Direct Access SPC-4 SCSI device
da1: Serial Number		 VKGWDP3X
da11: 7630885MB (1953506646 4096 byte sectors)
da1: 600.000MB/s transfers
da1: Command Queueing enabled
da1: 7630885MB (1953506646 4096 byte sectors)
ada0 at ahcich2 bus 0 scbus4 target 0 lun 0
ada0: <SATADOM-SV 3ME S140714> ACS-2 ATA SATA 3.x device
ada0: Serial Number 20160306AA1123141007
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 30533MB (62533296 512 byte sectors)
ada0: Previously was known as ad8
ada1 at ahcich5 bus 0 scbus7 target 0 lun 0
ada1: <SATADOM-SV 3ME S140714> ACS-2 ATA SATA 3.x device
ada1: Serial Number 20160306AA1123141011
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 30533MB (62533296 512 byte sectors)
ada1: Previously was known as ad14
GEOM: da0: the secondary GPT header is not in the last LBA.
SMP: AP CPU #6 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #7 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #4 Launched!
SMP: AP CPU #5 Launched!
Timecounter "TSC-low" frequency 1250027062 Hz quality 1000
GEOM: da1: the secondary GPT header is not in the last LBA.
GEOM: da2: the secondary GPT header is not in the last LBA.
GEOM: da3: the secondary GPT header is not in the last LBA.
GEOM: da4: the secondary GPT header is not in the last LBA.
GEOM: da5: the secondary GPT header is not in the last LBA.
GEOM: da6: the secondary GPT header is not in the last LBA.
GEOM: da7: the secondary GPT header is not in the last LBA.
GEOM: da8: the secondary GPT header is not in the last LBA.
GEOM: da10: the secondary GPT header is not in the last LBA.
GEOM: da11: the secondary GPT header is not in the last LBA.
GEOM: da12: the secondary GPT header is not in the last LBA.
GEOM: da13: the secondary GPT header is not in the last LBA.
GEOM: da14: the secondary GPT header is not in the last LBA.
GEOM: da15: the secondary GPT header is not in the last LBA.
GEOM: da16: the secondary GPT header is not in the last LBA.
GEOM: da17: the secondary GPT header is not in the last LBA.
GEOM: da18: the secondary GPT header is not in the last LBA.
Trying to mount root from zfs:freenas-boot/ROOT/9.10.1-U1 []...
GEOM_RAID5: Module loaded, version 1.3.20140711.62 (rev f91e28e40bf7)
GEOM_MULTIPATH: disk10 created
GEOM_MULTIPATH: da19 added to disk10
GEOM_MULTIPATH: da19 is now active path in disk10
GEOM_MULTIPATH: disk9 created
GEOM_MULTIPATH: da18 added to disk9
GEOM_MULTIPATH: da18 is now active path in disk9
GEOM_MULTIPATH: disk8 created
GEOM_MULTIPATH: da17 added to disk8
GEOM_MULTIPATH: da17 is now active path in disk8
GEOM_MULTIPATH: disk7 created
GEOM_MULTIPATH: da16 added to disk7
GEOM_MULTIPATH: da16 is now active path in disk7
GEOM_MULTIPATH: disk6 created
GEOM_MULTIPATH: da15 added to disk6
GEOM_MULTIPATH: da15 is now active path in disk6
GEOM_MULTIPATH: disk5 created
GEOM_MULTIPATH: da14 added to disk5
GEOM_MULTIPATH: da14 is now active path in disk5
GEOM_MULTIPATH: disk4 created
GEOM_MULTIPATH: da13 added to disk4
GEOM_MULTIPATH: da13 is now active path in disk4
GEOM_MULTIPATH: disk3 created
GEOM_MULTIPATH: da12 added to disk3
GEOM_MULTIPATH: da12 is now active path in disk3
GEOM_MULTIPATH: disk2 created
GEOM_MULTIPATH: da11 added to disk2
GEOM_MULTIPATH: da11 is now active path in disk2
GEOM_MULTIPATH: disk1 created
GEOM_MULTIPATH: da10 added to disk1
GEOM_MULTIPATH: da10 is now active path in disk1
GEOM_MULTIPATH: da9 added to disk10
GEOM_MULTIPATH: da8 added to disk9
GEOM_MULTIPATH: da7 added to disk8
GEOM_MULTIPATH: da6 added to disk7
GEOM_MULTIPATH: da5 added to disk6
GEOM_MULTIPATH: da4 added to disk5
GEOM_MULTIPATH: da3 added to disk4
GEOM_MULTIPATH: da2 added to disk3
GEOM_MULTIPATH: da1 added to disk2
GEOM_MULTIPATH: da0 added to disk1
ipmi0: <IPMI System Interface> port 0xca2,0xca3 on acpi0
ipmi0: KCS mode found at io 0xca2 on acpi
ipmi0: IPMI device rev. 1, firmware rev. 3.39, version 2.0
ipmi0: Number of channels 2
ipmi0: Attached watchdog
hwpmc: SOFT/16/64/0x67<INT,USR,SYS,REA,WRI> TSC/1/64/0x20<REA> IAP/8/48/0x3ff<INT,USR,SYS,EDG,THR,REA,WRI,INV,QUA,PRC> IAF/3/48/0x67<INT,USR,SYS,REA,WRI>
lagg0: link state changed to DOWN
ums0: <Winbond Electronics Corp Hermon USB hidmouse Device, class 0/0, rev 1.10/0.01, addr 3> on usbus0
ums0: 3 buttons and [Z] coordinates ID=0
igb0: link state changed to UP
lagg0: link state changed to UP
igb1: link state changed to UP
igb2: link state changed to UP
igb3: link state changed to UP
vboxdrv: fAsync=0 offMin=0x356 offMax=0x9048
GEOM_ELI: Device multipath/disk1p1.eli created.
GEOM_ELI: Encryption: AES-XTS 128
GEOM_ELI:	 Crypto: hardware
GEOM_ELI: Device multipath/disk2p1.eli created.
GEOM_ELI: Encryption: AES-XTS 128
GEOM_ELI:	 Crypto: hardware
GEOM_ELI: Device multipath/disk3p1.eli created.
GEOM_ELI: Encryption: AES-XTS 128
GEOM_ELI:	 Crypto: hardware
GEOM_ELI: Device multipath/disk4p1.eli created.
GEOM_ELI: Encryption: AES-XTS 128
GEOM_ELI:	 Crypto: hardware
GEOM_ELI: Device multipath/disk5p1.eli created.
GEOM_ELI: Encryption: AES-XTS 128
GEOM_ELI:	 Crypto: hardware
GEOM_ELI: Device multipath/disk6p1.eli created.
GEOM_ELI: Encryption: AES-XTS 128
GEOM_ELI:	 Crypto: hardware
GEOM_ELI: Device multipath/disk7p1.eli created.
GEOM_ELI: Encryption: AES-XTS 128
GEOM_ELI:	 Crypto: hardware
GEOM_ELI: Device multipath/disk8p1.eli created.
GEOM_ELI: Encryption: AES-XTS 128
GEOM_ELI:	 Crypto: hardware
GEOM_ELI: Device multipath/disk9p1.eli created.
GEOM_ELI: Encryption: AES-XTS 128
GEOM_ELI:	 Crypto: hardware
ses0: da0,pass0: Element descriptor: 'Slot 01'
ses0: da0,pass0: SAS Device Slot Element: 1 Phys at Slot 0
ses0:  phy 0: SAS device type 1 id 0
ses0:  phy 0: protocols: Initiator( None ) Target( SSP )
ses0:  phy 0: parent 500304801792497f addr 5000cca2543ee741
ses0: da1,pass1: Element descriptor: 'Slot 02'
ses0: da1,pass1: SAS Device Slot Element: 1 Phys at Slot 1
ses0:  phy 0: SAS device type 1 id 0
ses0:  phy 0: protocols: Initiator( None ) Target( SSP )
ses0:  phy 0: parent 500304801792497f addr 5000cca25431d67d
ses0: da2,pass2: Element descriptor: 'Slot 03'
ses0: da2,pass2: SAS Device Slot Element: 1 Phys at Slot 2
ses0:  phy 0: SAS device type 1 id 0
ses0:  phy 0: protocols: Initiator( None ) Target( SSP )
ses0:  phy 0: parent 500304801792497f addr 5000cca2542d10ed
ses0: da3,pass3: Element descriptor: 'Slot 04'
ses0: da3,pass3: SAS Device Slot Element: 1 Phys at Slot 3
GEOM_ELI: Device multipath/disk6p1.eli created.
GEOM_ELI: Encryption: AES-XTS 128
GEOM_ELI:	 Crypto: hardware
GEOM_ELI: Device multipath/disk7p1.eli created.
GEOM_ELI: Encryption: AES-XTS 128
GEOM_ELI:	 Crypto: hardware
GEOM_ELI: Device multipath/disk8p1.eli created.
GEOM_ELI: Encryption: AES-XTS 128
GEOM_ELI:	 Crypto: hardware
GEOM_ELI: Device multipath/disk9p1.eli created.
GEOM_ELI: Encryption: AES-XTS 128
GEOM_ELI:	 Crypto: hardware
ses0: da0,pass0: Element descriptor: 'Slot 01'
ses0: da0,pass0: SAS Device Slot Element: 1 Phys at Slot 0
ses0:  phy 0: SAS device type 1 id 0
ses0:  phy 0: protocols: Initiator( None ) Target( SSP )
ses0:  phy 0: parent 500304801792497f addr 5000cca2543ee741
ses0: da1,pass1: Element descriptor: 'Slot 02'
ses0: da1,pass1: SAS Device Slot Element: 1 Phys at Slot 1
ses0:  phy 0: SAS device type 1 id 0
ses0:  phy 0: protocols: Initiator( None ) Target( SSP )
ses0:  phy 0: parent 500304801792497f addr 5000cca25431d67d
ses0: da2,pass2: Element descriptor: 'Slot 03'
ses0: da2,pass2: SAS Device Slot Element: 1 Phys at Slot 2
ses0:  phy 0: SAS device type 1 id 0
ses0:  phy 0: protocols: Initiator( None ) Target( SSP )
ses0:  phy 0: parent 500304801792497f addr 5000cca2542d10ed
ses0: da3,pass3: Element descriptor: 'Slot 04'
ses0: da3,pass3: SAS Device Slot Element: 1 Phys at Slot 3
ses0:  phy 0: SAS device type 1 id 0
ses0:  phy 0: protocols: Initiator( None ) Target( SSP )
ses0:  phy 0: parent 500304801792497f addr 5000cca25440ee95
ses0: da4,pass4: Element descriptor: 'Slot 05'
ses0: da4,pass4: SAS Device Slot Element: 1 Phys at Slot 4
ses0:  phy 0: SAS device type 1 id 0
ses0:  phy 0: protocols: Initiator( None ) Target( SSP )
ses0:  phy 0: parent 500304801792497f addr 5000cca254412265
ses0: da5,pass5: Element descriptor: 'Slot 06'
ses0: da5,pass5: SAS Device Slot Element: 1 Phys at Slot 5
ses0:  phy 0: SAS device type 1 id 0
ses0:  phy 0: protocols: Initiator( None ) Target( SSP )
ses0:  phy 0: parent 500304801792497f addr 5000cca254402629
ses0: da6,pass6: Element descriptor: 'Slot 07'
ses0: da6,pass6: SAS Device Slot Element: 1 Phys at Slot 6
ses0:  phy 0: SAS device type 1 id 0
ses0:  phy 0: protocols: Initiator( None ) Target( SSP )
ses0:  phy 0: parent 500304801792497f addr 5000cca25437fd95
ses0: da7,pass7: Element descriptor: 'Slot 08'
ses0: da7,pass7: SAS Device Slot Element: 1 Phys at Slot 7
ses0:  phy 0: SAS device type 1 id 0
ses0:  phy 0: protocols: Initiator( None ) Target( SSP )
ses0:  phy 0: parent 500304801792497f addr 5000cca2543e37ad
ses0: da8,pass8: Element descriptor: 'Slot 09'
ses0: da8,pass8: SAS Device Slot Element: 1 Phys at Slot 8
ses0:  phy 0: SAS device type 1 id 0
ses0:  phy 0: protocols: Initiator( None ) Target( SSP )
ses0:  phy 0: parent 500304801792497f addr 5000cca2544242c9
ses0: da9,pass9: Element descriptor: 'Slot 13'
ses0: da9,pass9: SAS Device Slot Element: 1 Phys at Slot 12
ses0:  phy 0: SAS device type 1 id 0
ses0:  phy 0: protocols: Initiator( None ) Target( SSP )
ses0:  phy 0: parent 500304801792497f addr 5000cca260042119

 

[joeschmuck]

Well it appears that you have a lot of SAS drives connected. Because everything appears to be working, it might be a good thing to simply ask iXsystems (these folks are on this forum) if this is normal.

The other thing might be if you got a warning message about the LSI card needing a firmware upgrade to version 21.

Ensure all your data is backed up if you need to update the LSI board. Of course just unplugging the data cables would be good enough from the controller card.

 

[Sakuru]

The other thing might be if you got a warning message about the LSI card needing a firmware upgrade to version 21.

Firmware P21 does not exist. P20 is compatible with driver 21.

 

[joeschmuck]

Firmware P21 does not exist. P20 is compatible with driver 21.

Maybe my wording was not completely clear but I was only trying to express if they got the warning, maybe it would be a sign of something to troubleshoot. But then I mention about reprogramming the LSI card, and in my mind I was thinking about reflashing P20. Yup, not very clear. My apologies.

 

[mdrisser]

I have seen the message about needing to upgrade the firmware, but as it was there since we got the boxes from iXsystems I never gave it much thought. I guess I'll need to look in to reflashing P20. The intersting thing, and something I have seen in similar posts, is that if I go to Storage > View Multipaths I do see the drives, and they are showing up in dmesg, but not in Storage > View Disks. So I'm not really sure how re-flashing the firmware would be a benefit.

 

[joeschmuck]

I guess I'll need to look in to reflashing P20

Not really, I don't see that as your next step.

My advice: Submit a bug report (link at the top of the forum page) stating the problem. If there is a bug, it will get fixed. If it's not a bug, they will tell you why.