jaypetermen
Dabbler
- Joined
- Apr 1, 2015
- Messages
- 22
Every other day or so, one or two plugins stop running and I can not get them started. I typically reboot the NAS and then none of the plugin will start.
I have tried the following with no success:
The only remedy that I have found is to delete all the jails storage, deleting all the plugins, re-installing all the plugins, adding jail storage and then manually re-configuring each plugin manually. Then after a day or two one on the plugin turns off, the plugin cannot be restated, I reboot my NAS, then none of the plugins will start, and the whole whole process starts over again.
I would like to find out why the plugins will not start and/or if there is a way to at least save the plugin configurations some how, so when I need to re-install the plugins, I would not need to go through and set up each plugin environments manually.
FreeNAS-9.3-STABLE-201503200528
Motherboard ASUS A55BM-PLUS/CSM FM2+ / FM2 AMD A55 (Hudson D2)
AMD A6-5400K APU with Radeon(tm) HD Graphics
Memory 7339MB
2x WD Red 3TB NAS Hard Drive striped
100 Gigabit ethernet
I have tried the following with no success:
- Restating all jails.
- Stopping all jails and then ran 'service ix-plugins forcerestart' from the shell.
- Stopping all jails, deleting the jails storage, re-adding jail storage, and then ran 'service ix-plugins forcerestart' from the shell.
- Changing the IPv4 DHCP in the jail configuration, since I am running DHCP on the router, and then rebooted the NAS.
The only remedy that I have found is to delete all the jails storage, deleting all the plugins, re-installing all the plugins, adding jail storage and then manually re-configuring each plugin manually. Then after a day or two one on the plugin turns off, the plugin cannot be restated, I reboot my NAS, then none of the plugins will start, and the whole whole process starts over again.
I would like to find out why the plugins will not start and/or if there is a way to at least save the plugin configurations some how, so when I need to re-install the plugins, I would not need to go through and set up each plugin environments manually.
Code:
epair1b: Ethernet address: 02:e1:3b:00:0b:0b epair1a: link state changed to UP epair1b: link state changed to UP epair1a: promiscuous mode enabled ng_ether_ifnet_arrival_event: can't re-name node epair1b arp: 6c:ad:f8:2c:51:81 is using my IP address 192.168.0.2 on epair1b! epair2a: Ethernet address: 02:eb:3b:00:0b:0a epair2b: Ethernet address: 02:eb:3b:00:0c:0b epair2a: link state changed to UP epair2b: link state changed to UP epair2a: promiscuous mode enabled ng_ether_ifnet_arrival_event: can't re-name node epair2b epair3a: Ethernet address: 02:b1:3e:00:0c:0a epair3b: Ethernet address: 02:b1:3e:00:0d:0b epair3a: link state changed to UP epair3b: link state changed to UP epair3a: promiscuous mode enabled ng_ether_ifnet_arrival_event: can't re-name node epair3b arp: 192.168.0.2 moved from 02:2a:fb:00:0a:0b to 6c:ad:f8:2c:51:81 on re0 arp: 6c:ad:f8:2c:51:81 is using my IP address 192.168.0.2 on epair1b! arp: 6c:ad:f8:2c:51:81 is using my IP address 192.168.0.2 on epair1b! arp: 6c:ad:f8:2c:51:81 is using my IP address 192.168.0.2 on epair1b! arp: 6c:ad:f8:2c:51:81 is using my IP address 192.168.0.2 on epair1b!
Code:
media: Ethernet 10Gbase-T (10Gbase-T <full-duplex>) status: active epair1a: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 02:e1:3b:00:0a:0a nd6 options=1<PERFORMNUD> media: Ethernet 10Gbase-T (10Gbase-T <full-duplex>) status: active epair2a: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 02:eb:3b:00:0b:0a nd6 options=1<PERFORMNUD> media: Ethernet 10Gbase-T (10Gbase-T <full-duplex>) status: active epair3a: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 02:b1:3e:00:0c:0a nd6 options=1<PERFORMNUD> media: Ethernet 10Gbase-T (10Gbase-T <full-duplex>) status: active
Code:
Routing tables Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.0.1 UGS 0 641 re0 127.0.0.1 link#7 UH 0 8111 lo0 192.168.0.0/24 link#5 U 0 1622 re0 192.168.0.13 link#5 UHS 0 207 lo0 Internet6: Destination Gateway Flags Netif Expire ::/96 ::1 UGRS lo0 ::1 link#7 UH lo0 ::ffff:0.0.0.0/96 ::1 UGRS lo0 fe80::/10 ::1 UGRS lo0 fe80::%lo0/64 link#7 U lo0 fe80::1%lo0 link#7 UHS lo0 ff01::%lo0/32 ::1 U lo0 ff02::/16 ::1 UGRS lo0 ff02::%lo0/32 ::1 U lo0 [root@freenas ~]#
Code:
[root@freenas ~]# jls JID IP Address Hostname Path 1 - couchpotato_1 /mnt/plex/jails/couchpotat o_1 2 - plexmediaserver_1 /mnt/plex/jails/plexmedias erver_1 3 - sabnzbd_1 /mnt/plex/jails/sabnzbd_1 4 - sonarr_1 /mnt/plex/jails/sonarr_1
FreeNAS-9.3-STABLE-201503200528
Motherboard ASUS A55BM-PLUS/CSM FM2+ / FM2 AMD A55 (Hudson D2)
AMD A6-5400K APU with Radeon(tm) HD Graphics
Memory 7339MB
2x WD Red 3TB NAS Hard Drive striped
100 Gigabit ethernet