Hi all,
After doing some web searching, looking behind the shed and in the neighbors couch, I look to you fine folks for the answers I was unable to find.
I have been running the latest release FreeNas version 11.2 u4 or there about and previous version without problems.
This leads me to today where I tried to do the following:
Problem:
Add 2 new users and a group and changed the namw of a previous group.
While i was mucking about with the permissions, the WEB UI began lagging and became non responsive, to which I had to restart.
When the system came back to life the following issue appeared on the screen attached to the FN box - Console setup, under the 11 config options where your IP should be, I get this:
"The Web interface could not be accessed. Please check network configuration."
Needless to say, I can't access the FN web UI.
When I try access the web UI i get:
"404 not Found
nginx"
All my mapped drives and sub folders are still accessible via Windows network etc. (\\freenas)
I can ping the FN box and get a response.
I tried to SSH into the FN box with hopes and dreams, but alas, I noticed an issue:
"Welcome to FreeNAS
Could not chdir to home directory /nonexistent: No such file or directory"
I used my user access, not root (root access disabled via ssh)
I did an ifconfig from SSH as per below:
Code:
% ifconfig
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether 4c:cc:6a:f4:ae:2e
hwaddr 4c:cc:6a:f4:ae:2e
inet 192.168.1.233 netmask 0xffffff00 broadcast 192.168.1.255
inet 192.168.1.235 netmask 0xffffffff broadcast 192.168.1.235
inet 192.168.1.234 netmask 0xffffffff broadcast 192.168.1.234
nd6 options=9<PERFORMNUD,IFDISABLED>
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
inet 127.0.0.1 netmask 0xff000000
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
groups: lo
%
192.168.1.233 is my FN box (192.168.1.234 and 192.168.1.235 are a couple emby servers)
I did change the /nonexistant of the two new users to something else but changed back before all this happened.
I also deleted the two new users via FN shell. (last action before posting here)
If you could shed some light onto this issue I would be grateful!!!!!
My system is as follows:
After doing some web searching, looking behind the shed and in the neighbors couch, I look to you fine folks for the answers I was unable to find.
I have been running the latest release FreeNas version 11.2 u4 or there about and previous version without problems.
This leads me to today where I tried to do the following:
Problem:
Add 2 new users and a group and changed the namw of a previous group.
While i was mucking about with the permissions, the WEB UI began lagging and became non responsive, to which I had to restart.
When the system came back to life the following issue appeared on the screen attached to the FN box - Console setup, under the 11 config options where your IP should be, I get this:
"The Web interface could not be accessed. Please check network configuration."
Needless to say, I can't access the FN web UI.
When I try access the web UI i get:
"404 not Found
nginx"
All my mapped drives and sub folders are still accessible via Windows network etc. (\\freenas)
I can ping the FN box and get a response.
I tried to SSH into the FN box with hopes and dreams, but alas, I noticed an issue:
"Welcome to FreeNAS
Could not chdir to home directory /nonexistent: No such file or directory"
I used my user access, not root (root access disabled via ssh)
I did an ifconfig from SSH as per below:
Code:
% ifconfig
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether 4c:cc:6a:f4:ae:2e
hwaddr 4c:cc:6a:f4:ae:2e
inet 192.168.1.233 netmask 0xffffff00 broadcast 192.168.1.255
inet 192.168.1.235 netmask 0xffffffff broadcast 192.168.1.235
inet 192.168.1.234 netmask 0xffffffff broadcast 192.168.1.234
nd6 options=9<PERFORMNUD,IFDISABLED>
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
inet 127.0.0.1 netmask 0xff000000
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
groups: lo
%
192.168.1.233 is my FN box (192.168.1.234 and 192.168.1.235 are a couple emby servers)
I did change the /nonexistant of the two new users to something else but changed back before all this happened.
I also deleted the two new users via FN shell. (last action before posting here)
If you could shed some light onto this issue I would be grateful!!!!!
My system is as follows:
- Motherboard: MSI H81I
- CPU: Intel I5-4430 LGA1150
- RAM: 8gb Corsair Vengeance 1866 MHz
- Hard drives: 2 x 4 tb wd red in mirror config, 1 x 120GB ssd OCZ for boot
- Nothing else added.
Last edited: