Drive needs to be replaced?

[evillone]

Greetings all,
just finished updating this evening from 9.3 and got as far as 11.2-U8
after upgrading my Pool a couple times i now have a degraded message.
I'm pretty sure one of my drives are gone ( which i expected i have 2 left from a bad batch )
and this version seems to show things a little different in the GUI , and shows no errors etc in zpool status,
, just wanted to verify with you folks first .


pool:
state: DEGRADED
status: One or more devices could not be opened. Sufficient replicas exist for
the pool to continue functioning in a degraded state.
action: Attach the missing device and online it using 'zpool online'.
see: http://illumos.org/msg/ZFS-8000-2Q
scan: scrub repaired 630M in 1 days 00:19:21 with 0 errors on Mon Jun 1 00:19:22 2020
config:

NAME STATE READ WRITE CKSUM
DEGRADED 0 0 0
raidz1-0 DEGRADED 0 0 0
11293713218029400292 UNAVAIL 0 0 0 was /dev/gptid/683b83af-4cf1-11e5-8f38-6805ca32cdb3
gptid/68f0342d-4cf1-11e5-8f38-6805ca32cdb3 ONLINE 0 0 0
gptid/7053cea4-be45-11e5-9c31-6805ca32cdb3 ONLINE 0 0 0
gptid/6a114719-4cf1-11e5-8f38-6805ca32cdb3 ONLINE 0 0 0
gptid/6a64799b-4cf1-11e5-8f38-6805ca32cdb3 ONLINE 0 0 0
gptid/7bd17363-1963-11e6-9ccc-6805ca32cdb3 ONLINE 0 0 0

errors: No known data errors

pool: freenas-boot
state: ONLINE
scan: scrub repaired 0 in 0 days 00:10:58 with 0 errors on Sun Jun 7 03:55:58 2020
config:

NAME STATE READ WRITE CKSUM
freenas-boot ONLINE 0 0 0
da0p2 ONLINE 0 0 0

errors: No known data errors

 

[c77dk]

Hi,

One of the disks is unavailable according to the output:

11293713218029400292 UNAVAIL 0 0 0 was /dev/gptid/683b83af-4cf1-11e5-8f38-6805ca32cdb3

Using "glabel status" you might be able to figure out which disk it is.

 

[evillone]

Hi,

One of the disks is unavailable according to the output:



Using "glabel status" you might be able to figure out which disk it is.

thanks ! ,
yes i have isolated the disk, but is unavailable a connection issue ? or the drive is gone gone

 

[Samuel Tai]

is unavailable a connection issue ? or the drive is gone gone

Could be either. Try reseating the connections first or swapping connections with another disk. (FreeNAS doesn't care about the actual connection, but uses gptid to identify the disk.) If that doesn't work, the drive is gone.

 

[evillone]

Could be either. Try reseating the connections first or swapping connections with another disk. (FreeNAS doesn't care about the actual connection, but uses gptid to identify the disk.) If that doesn't work, the drive is gone.

Great, that's what I figured,
I have tried re-seating the controller and changing Sata ports and a cable, still the same thing.
Ordering a RED drive,
thanks again for the info folks,
much appreciated !!!

PS: The new interface is AWESOME !!!!!

 

[Samuel Tai]

Ordering a RED drive,

Make sure you don't order an SMR drive (EFAX, between 2-6 TB capacities), but have instead ordered a CMR drive (EFRX, or EFAX outside the problematic sizes).

 

[evillone]

Make sure you don't order an SMR drive (EFAX, between 2-6 TB capacities), but have instead ordered a CMR drive (EFRX, or EFAX outside the problematic sizes).

Thanks Samuel,

since i already have 3 in the NAS i went with a 3TB WD30EFRX which i believe is CMR