Stuck resilvering after drive replacement

[markw78]

Well, I didn't follow the directions, I thought.. how hard can it be?

So here's what I did. We had a disk with bad sectors being remapped. I went to the server, unplugged the disk, and connected teh new one. When I came back to the console I realized nothing had happened on the server.

I went to Disks and did a Detach of the bad disk. This disk went away from the console. The new disk would not show up, so I figured my hardware doesn't have hot swappable SATA. I rebooted, and the new disk was there. Clicked Replace.

Now I'm stuck... The GUI shows everything as it should be. Only the new disk is present, in a good state, no problems at all.

When I go to the CLI though, I get this:

# zpool status
pool: Data
state: DEGRADED
scrub: resilver completed after 0h0m with 0 errors on Mon Dec 10 17:25:22 2012
config:

NAME STATE READ WRITE CKSUM
Data DEGRADED 0 0 0
raidz2 DEGRADED 0 0 0
gptid/6ae193df-4312-11e2-b638-001a92837d47 ONLINE 0 0 0
replacing DEGRADED 0 0 0
gptid/6b667e9e-4312-11e2-b638-001a92837d47 OFFLINE 0 0 0
gptid/dde193dd-4320-11e2-a8ad-001a92837d47 ONLINE 0 0 0 20.2M resilvered
gptid/6bcadcc4-4312-11e2-b638-001a92837d47 ONLINE 0 0 0
gptid/6c4eec74-4312-11e2-b638-001a92837d47 ONLINE 0 0 0
gptid/6ce71ade-4312-11e2-b638-001a92837d47 ONLINE 0 0 0
logs
gptid/6d2e658d-4312-11e2-b638-001a92837d47 ONLINE 0 0 0

errors: No known data errors

Nothing has changed here for over 24 hours now. I just need to remove the OFFLINE disk as it's no longer in the system. It's early enough on that I could delete the pool and start again, but I'd still rather not.

Thanks!
Mark

 

[bollar]

When you look at Storage: Volume Status in your GUI, what are your choices for the new drive? Edit, Replace & Offline? A screenshot would be helpful.

 

[markw78]

The old disk was still there, with a Detach option only. I clicked it. zpool status still looks the same, but will give it time.

Since doing that, the Volume Status page looks 100% perfect, everything Online and as it should be.

 

[markw78]

and now...

# zpool status -v
pool: Data
state: ONLINE
scrub: resilver completed after 0h0m with 0 errors on Mon Dec 10 17:25:22 2012
config:

NAME STATE READ WRITE CKSUM
Data ONLINE 0 0 0
raidz2 ONLINE 0 0 0
gptid/6ae193df-4312-11e2-b638-001a92837d47 ONLINE 0 0 0
gptid/dde193dd-4320-11e2-a8ad-001a92837d47 ONLINE 0 0 0 20.2M resilvered
gptid/6bcadcc4-4312-11e2-b638-001a92837d47 ONLINE 0 0 0
gptid/6c4eec74-4312-11e2-b638-001a92837d47 ONLINE 0 0 0
gptid/6ce71ade-4312-11e2-b638-001a92837d47 ONLINE 0 0 0
logs
gptid/6d2e658d-4312-11e2-b638-001a92837d47 ONLINE 0 0 0

errors: No known data errors

Thank you for the help! I always look at the "Disks" page, instead of "Volume Status".