SCSI Status: Check Condition(s)

C

cfgmgr

Cadet
Joined
Jan 9, 2015
Messages
9
Howdy all!

Just recently moved from an older Supermicro X9 build (with one of the older 16 bay chassis) with an LSI2008 onboard SAS and an IBM M1015 HBA to a SuperStorage 5049P-E1CTR36L. I don't recall seeing any of these errors before (had prior system for 4+ years) and the pool the errors came on I've had for 2ish.

I migrated the pools from old to new system without issue. Everything is currently online and I do not believe at the time these errors occurred I was stressing the pool particularly. These disks are used an I will be eventually moving off of them for SSD instead. So far they have been serving as a pool for a bunch of VM's that I have been testing. It's been performing OK and doing its job but will eventually be retired (or kept as empty storage/spared for other things).

As mentioned, this particular pool is serving two ZVOL's via iSCSI. I ran the exact setup on the older box and didn't see any errors like this before. I would see some noise previously, but only if I was stressing the pool which did not suprise me due to the poor disk layout of this pool.

Attached Hypervisors are all VMware 6.7 U2. Setup has been rock solid the last few years no issues. Again disks are used, and they had a pretty high Load_Cycle_Count (see below). Perhaps those are the culprit


Here is the current Hardware list:
SuperStorage 5049P-E1CTR36L
X11SPH-nCTF
Onboard SAS LSI 3008 flashed to IT mode
128GB Samsung DDR4 2666MHz
Intel X520 (82599ES)
Intel Optane 900p (480GB) - SLOG

HBA Driver/Firmware
Code:
# sas3flash -list
Avago Technologies SAS3 Flash Utility
Version 16.00.00.00 (2017.05.02)
Copyright 2008-2017 Avago Technologies. All rights reserved.

        Adapter Selected is a Avago SAS: SAS3008(C0)

        Controller Number              : 0
        Controller                     : SAS3008(C0)
        PCI Address                    : 00:19:00:00
        SAS Address                    : 5003048-0-1cd2-dc03
        NVDATA Version (Default)       : 0e.01.30.28
        NVDATA Version (Persistent)    : 0e.01.30.28
        Firmware Product ID            : 0x2221 (IT)
        Firmware Version               : 16.00.01.00
        NVDATA Vendor                  : LSI
        NVDATA Product ID              : LSI3008-IT
        BIOS Version                   : 08.37.00.00
        UEFI BSD Version               : 18.00.00.00
        FCODE Version                  : N/A
        Board Name                     : LSI3008-IT
        Board Assembly                 : N/A
        Board Tracer Number            : N/A

        Finished Processing Commands Successfully.
        Exiting SAS3Flash.



Disk List:
Code:
# camcontrol devlist -v
scbus0 on ahcich0 bus 0:
<SuperMicro SSD SOB20R>            at scbus0 target 0 lun 0 (pass0,ada0)
<>                                 at scbus0 target -1 lun ffffffff ()
scbus1 on ahcich1 bus 0:
<SuperMicro SSD SOB20R>            at scbus1 target 0 lun 0 (pass1,ada1)
<>                                 at scbus1 target -1 lun ffffffff ()
scbus2 on ahcich2 bus 0:
<>                                 at scbus2 target -1 lun ffffffff ()
scbus3 on ahcich3 bus 0:
<>                                 at scbus3 target -1 lun ffffffff ()
scbus4 on ahcich4 bus 0:
<>                                 at scbus4 target -1 lun ffffffff ()
scbus5 on ahcich5 bus 0:
<>                                 at scbus5 target -1 lun ffffffff ()
scbus6 on ahcich6 bus 0:
<>                                 at scbus6 target -1 lun ffffffff ()
scbus7 on ahcich7 bus 0:
<>                                 at scbus7 target -1 lun ffffffff ()
scbus8 on ahcich8 bus 0:
<>                                 at scbus8 target -1 lun ffffffff ()
scbus9 on ahcich9 bus 0:
<>                                 at scbus9 target -1 lun ffffffff ()
scbus10 on mpr0 bus 0:
<ATA CT2000MX500SSD1 023>          at scbus10 target 11 lun 0 (da18,pass22)
<ATA CT2000MX500SSD1 023>          at scbus10 target 12 lun 0 (da14,pass18)
<ATA CT2000MX500SSD1 023>          at scbus10 target 13 lun 0 (da10,pass14)
<ATA CT2000MX500SSD1 023>          at scbus10 target 17 lun 0 (da19,pass23)
<ATA CT2000MX500SSD1 023>          at scbus10 target 18 lun 0 (da15,pass19)
<ATA CT2000MX500SSD1 023>          at scbus10 target 19 lun 0 (da11,pass15)
<ATA CT2000MX500SSD1 023>          at scbus10 target 23 lun 0 (da20,pass24)
<ATA CT2000MX500SSD1 023>          at scbus10 target 24 lun 0 (da16,pass20)
<ATA CT2000MX500SSD1 023>          at scbus10 target 25 lun 0 (da12,pass16)
<ATA CT2000MX500SSD1 023>          at scbus10 target 29 lun 0 (da21,pass25)
<ATA CT2000MX500SSD1 023>          at scbus10 target 30 lun 0 (da17,pass21)
<ATA CT2000MX500SSD1 023>          at scbus10 target 31 lun 0 (da13,pass17)
<SMC SC846P 0c1f>                  at scbus10 target 32 lun 0 (pass2,ses0)
<ATA WDC WD60EFRX-68M 0A82>        at scbus10 target 51 lun 0 (pass3,da0)
<ATA WDC WD40EFRX-68W 0A80>        at scbus10 target 52 lun 0 (pass4,da1)
<ATA WDC WD40EFRX-68W 0A80>        at scbus10 target 53 lun 0 (pass5,da2)
<ATA WDC WD60EFRX-68M 0A82>        at scbus10 target 54 lun 0 (pass6,da3)
<ATA WDC WD40EFRX-68W 0A82>        at scbus10 target 55 lun 0 (pass7,da4)
<ATA WDC WD40EFRX-68W 0A80>        at scbus10 target 56 lun 0 (pass8,da5)
<ATA WDC WD60EFRX-68M 0A82>        at scbus10 target 58 lun 0 (pass9,da6)
<ATA WDC WD40EFRX-68W 0A80>        at scbus10 target 59 lun 0 (pass10,da7)
<ATA WDC WD60EFRX-68M 0A82>        at scbus10 target 61 lun 0 (pass11,da8)
<ATA WDC WD40EFRX-68W 0A80>        at scbus10 target 62 lun 0 (pass12,da9)
<SMC SC826P 0c1f>                  at scbus10 target 63 lun 0 (pass13,ses1)
<>                                 at scbus10 target -1 lun ffffffff ()
scbus11 on camsim0 bus 0:
<>                                 at scbus11 target -1 lun ffffffff ()
scbus-1 on xpt0 bus 0:
<>                                 at scbus-1 target -1 lun ffffffff (xpt0)


Entire Pool LIst, "vmware" is the pool in question:
Code:
# zpool status
  pool: bucket
 state: ONLINE
  scan: scrub repaired 0 in 0 days 00:14:29 with 0 errors on Sun Sep  1 00:14:30 2019
config:

        NAME                                            STATE     READ WRITE CKSUM
        bucket                                          ONLINE       0     0     0
          raidz2-0                                      ONLINE       0     0     0
            gptid/1a7255f7-a768-11e4-bb0d-0cc47a17532e  ONLINE       0     0     0
            gptid/1ad46006-a768-11e4-bb0d-0cc47a17532e  ONLINE       0     0     0
            gptid/1b37e43e-a768-11e4-bb0d-0cc47a17532e  ONLINE       0     0     0
            gptid/1bab5d4e-a768-11e4-bb0d-0cc47a17532e  ONLINE       0     0     0
            gptid/1c1432aa-a768-11e4-bb0d-0cc47a17532e  ONLINE       0     0     0
            gptid/1c76ebdc-a768-11e4-bb0d-0cc47a17532e  ONLINE       0     0     0

errors: No known data errors

  pool: freenas-boot
 state: ONLINE
  scan: none requested
config:

        NAME        STATE     READ WRITE CKSUM
        freenas-boot  ONLINE       0     0     0
          mirror-0  ONLINE       0     0     0
            ada0p2  ONLINE       0     0     0
            ada1p2  ONLINE       0     0     0

errors: No known data errors

  pool: vmware
 state: ONLINE
  scan: resilvered 1.27M in 0 days 00:00:01 with 0 errors on Thu Sep  5 22:09:47 2019
config:

        NAME                                            STATE     READ WRITE CKSUM
        vmware                                          ONLINE       0     0     0
          raidz1-0                                      ONLINE       0     0     0
            gptid/a804ef0f-ff69-11e8-a676-0cc47a17532e  ONLINE       0     0     0
            gptid/a91db902-ff69-11e8-a676-0cc47a17532e  ONLINE       0     0     0
            gptid/aa30e266-ff69-11e8-a676-0cc47a17532e  ONLINE       0     0     0
            gptid/acd2fef9-ff69-11e8-a676-0cc47a17532e  ONLINE       0     0     0
        logs
          nvd0p1                                        ONLINE       0     0     0

errors: No known data errors

  pool: vmware-ssd
 state: ONLINE
  scan: none requested
config:

        NAME                                            STATE     READ WRITE CKSUM
        vmware-ssd                                      ONLINE       0     0     0
          mirror-0                                      ONLINE       0     0     0
            gptid/7e389fbd-d99a-11e9-a453-ac1f6bbba0e8  ONLINE       0     0     0
            gptid/7eb44778-d99a-11e9-a453-ac1f6bbba0e8  ONLINE       0     0     0
          mirror-1                                      ONLINE       0     0     0
            gptid/7f35d35e-d99a-11e9-a453-ac1f6bbba0e8  ONLINE       0     0     0
            gptid/7fb54f65-d99a-11e9-a453-ac1f6bbba0e8  ONLINE       0     0     0
          mirror-2                                      ONLINE       0     0     0
            gptid/804952b3-d99a-11e9-a453-ac1f6bbba0e8  ONLINE       0     0     0
            gptid/80cc65c2-d99a-11e9-a453-ac1f6bbba0e8  ONLINE       0     0     0
          mirror-3                                      ONLINE       0     0     0
            gptid/814bc69b-d99a-11e9-a453-ac1f6bbba0e8  ONLINE       0     0     0
            gptid/81d0e894-d99a-11e9-a453-ac1f6bbba0e8  ONLINE       0     0     0
          mirror-4                                      ONLINE       0     0     0
            gptid/8259d4ec-d99a-11e9-a453-ac1f6bbba0e8  ONLINE       0     0     0
            gptid/82e05b85-d99a-11e9-a453-ac1f6bbba0e8  ONLINE       0     0     0
          mirror-5                                      ONLINE       0     0     0
            gptid/8379784c-d99a-11e9-a453-ac1f6bbba0e8  ONLINE       0     0     0
            gptid/83ffc9d9-d99a-11e9-a453-ac1f6bbba0e8  ONLINE       0     0     0
        logs
          nvd0p2                                        ONLINE       0     0     0

errors: No known data errors
 
C

cfgmgr

Cadet
Joined
Jan 9, 2015
Messages
9
Had to add in smartctl data later due to size limit. Also forgot to put up top, running FreeNAS-11.2-U5. Will probably update to U6 very soon.

Code:
root@san01:/var/log # smartctl -a /dev/da0
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.2-STABLE amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red
Device Model:     WDC WD60EFRX-68MYMN1
Serial Number:    WD-WX31D55DF0EV
LU WWN Device Id: 5 0014ee 20c45bc61
Firmware Version: 82.00A82
User Capacity:    6,001,175,126,016 bytes [6.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5700 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Sep 19 07:17:15 2019 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                ( 3584) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 689) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x303d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   188   188   021    Pre-fail  Always       -       9566
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       910
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   053   053   000    Old_age   Always       -       34556
10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       25
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       13
193 Load_Cycle_Count        0x0032   190   190   000    Old_age   Always       -       31915
194 Temperature_Celsius     0x0022   114   113   000    Old_age   Always       -       38
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     27848         -
# 2  Short offline       Completed without error       00%     27680         -
# 3  Short offline       Completed without error       00%     27512         -
# 4  Short offline       Completed without error       00%     27344         -
# 5  Short offline       Completed without error       00%     27176         -
# 6  Short offline       Completed without error       00%     27008         -
# 7  Short offline       Completed without error       00%     26840         -
# 8  Short offline       Completed without error       00%     26672         -
# 9  Short offline       Completed without error       00%     26504         -
#10  Short offline       Completed without error       00%     26337         -
#11  Short offline       Completed without error       00%     26169         -
#12  Short offline       Completed without error       00%     26001         -
#13  Short offline       Completed without error       00%     25833         -
#14  Short offline       Completed without error       00%     25665         -
#15  Short offline       Completed without error       00%     25497         -
#16  Short offline       Completed without error       00%     25330         -
#17  Short offline       Completed without error       00%     25162         -
#18  Short offline       Completed without error       00%     24994         -
#19  Short offline       Completed without error       00%     24826         -
#20  Short offline       Completed without error       00%     24658         -
#21  Short offline       Completed without error       00%     24490         -

SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log # smartctl -a /dev/da3
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.2-STABLE amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red
Device Model:     WDC WD60EFRX-68MYMN1
Serial Number:    WD-WX31D55A4DUX
LU WWN Device Id: 5 0014ee 261956adb
Firmware Version: 82.00A82
User Capacity:    6,001,175,126,016 bytes [6.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5700 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Sep 19 07:17:46 2019 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                ( 1064) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 665) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x303d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   195   195   021    Pre-fail  Always       -       9250
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       908
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   053   053   000    Old_age   Always       -       34525
10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       23
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       13
193 Load_Cycle_Count        0x0032   190   190   000    Old_age   Always       -       31826
194 Temperature_Celsius     0x0022   111   110   000    Old_age   Always       -       41
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     27816         -
# 2  Short offline       Completed without error       00%     27649         -
# 3  Short offline       Completed without error       00%     27481         -
# 4  Short offline       Completed without error       00%     27313         -
# 5  Short offline       Completed without error       00%     27144         -
# 6  Short offline       Completed without error       00%     26976         -
# 7  Short offline       Completed without error       00%     26809         -
# 8  Short offline       Completed without error       00%     26641         -
# 9  Short offline       Completed without error       00%     26473         -
#10  Short offline       Completed without error       00%     26305         -
#11  Short offline       Completed without error       00%     26137         -
#12  Short offline       Completed without error       00%     25969         -
#13  Short offline       Completed without error       00%     25802         -
#14  Short offline       Completed without error       00%     25634         -
#15  Short offline       Completed without error       00%     25466         -
#16  Short offline       Completed without error       00%     25298         -
#17  Short offline       Completed without error       00%     25130         -
#18  Short offline       Completed without error       00%     24963         -
#19  Short offline       Completed without error       00%     24795         -
#20  Short offline       Completed without error       00%     24627         -
#21  Short offline       Completed without error       00%     24459         -

SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log # smartctl -a /dev/da6
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.2-STABLE amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red
Device Model:     WDC WD60EFRX-68MYMN1
Serial Number:    WD-WX31D55A4XS3
LU WWN Device Id: 5 0014ee 20c4009d8
Firmware Version: 82.00A82
User Capacity:    6,001,175,126,016 bytes [6.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5700 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Sep 19 07:18:10 2019 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                ( 2144) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 675) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x303d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   197   197   021    Pre-fail  Always       -       9125
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       239
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   055   055   000    Old_age   Always       -       33564
10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       25
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       12
193 Load_Cycle_Count        0x0032   191   191   000    Old_age   Always       -       28746
194 Temperature_Celsius     0x0022   116   115   000    Old_age   Always       -       36
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     26856         -
# 2  Short offline       Completed without error       00%     26688         -
# 3  Short offline       Completed without error       00%     26521         -
# 4  Short offline       Completed without error       00%     26353         -
# 5  Short offline       Completed without error       00%     26184         -
# 6  Short offline       Completed without error       00%     26016         -
# 7  Short offline       Completed without error       00%     25848         -
# 8  Short offline       Completed without error       00%     25680         -
# 9  Short offline       Completed without error       00%     25513         -
#10  Short offline       Completed without error       00%     25345         -
#11  Short offline       Completed without error       00%     25177         -
#12  Short offline       Completed without error       00%     25009         -
#13  Short offline       Completed without error       00%     24841         -
#14  Short offline       Completed without error       00%     24674         -
#15  Short offline       Completed without error       00%     24579         -
#16  Short offline       Completed without error       00%     19170         -
#17  Short offline       Completed without error       00%     19003         -
#18  Short offline       Completed without error       00%     18835         -
#19  Short offline       Completed without error       00%     18667         -
#20  Short offline       Completed without error       00%     18498         -
#21  Short offline       Completed without error       00%     18330         -

SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log #
root@san01:/var/log # smartctl -a /dev/da8
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.2-STABLE amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red
Device Model:     WDC WD60EFRX-68MYMN1
Serial Number:    WD-WX31DB48XPKD
LU WWN Device Id: 5 0014ee 20b8b3bb2
Firmware Version: 82.00A82
User Capacity:    6,001,175,126,016 bytes [6.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5700 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Sep 19 07:18:33 2019 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                ( 5984) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 713) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x303d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   194   194   021    Pre-fail  Always       -       9291
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       938
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   052   052   000    Old_age   Always       -       35152
10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       25
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       14
193 Load_Cycle_Count        0x0032   190   190   000    Old_age   Always       -       30469
194 Temperature_Celsius     0x0022   117   115   000    Old_age   Always       -       35
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     28444         -
# 2  Short offline       Completed without error       00%     28276         -
# 3  Short offline       Completed without error       00%     28109         -
# 4  Short offline       Completed without error       00%     27941         -
# 5  Short offline       Completed without error       00%     27772         -
# 6  Short offline       Completed without error       00%     27604         -
# 7  Short offline       Completed without error       00%     27436         -
# 8  Short offline       Completed without error       00%     27269         -
# 9  Short offline       Completed without error       00%     27101         -
#10  Short offline       Completed without error       00%     26933         -
#11  Short offline       Completed without error       00%     26765         -
#12  Short offline       Completed without error       00%     26597         -
#13  Short offline       Completed without error       00%     26429         -
#14  Short offline       Completed without error       00%     26262         -
#15  Short offline       Completed without error       00%     26094         -
#16  Short offline       Completed without error       00%     25926         -
#17  Short offline       Completed without error       00%     25758         -
#18  Short offline       Completed without error       00%     25590         -
#19  Short offline       Completed without error       00%     25422         -
#20  Short offline       Completed without error       00%     25255         -
#21  Short offline       Completed without error       00%     25087         -

SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
 
C

cfgmgr

Cadet
Joined
Jan 9, 2015
Messages
9
Nope. I went back to the drawing board as I was suspect of these were due to other activities, even though I didn't think the time stamps lined up.

I verified indeed they ultimately were!

I was cold booting 9 VM's in one shot via vCenter on a pool that isn't build properly (which I'm aware of). I have pool full of SSD's just haven't moved things over yet.

I was used to seeing these errors on the older hardware (different driver) but the output changed a bit and I was a bit spooked.

All is well, thanks for checking back! Was meaning to update this poster earlier with my findings!
 
You must log in or register to reply here.

Similar threads

P
SOLVED Need imediate input regarding drive replacement
Replies
3
Views
945
jgreco
jgreco
E
SOLVED Having Trouble Upgrading Storage / Degraded
Replies
6
Views
2K
jlaudiofan
J
T
  • Locked
ZPOOL degraded, hdd failed and so did my attempt to replace
Replies
3
Views
2K
paleoN
paleoN
mtaksrud
  • Locked
Pool missing after upgrading to 11.1-U5
Replies
13
Views
2K
jgreco
jgreco
BTW
  • Locked
Not Sure what hard drive has failed?
Replies
9
Views
2K
BTW
BTW
Top