SatchaDahmi
Cadet
- Joined
- Apr 25, 2019
- Messages
- 7
Hey guys,
I just had the board fail in my stand alone system for freenas and now for a couple months until I can upgrade that I need to move Freenas to a VM with Passthrough. I am on ESXI 6.7 and running freenas 11.2u4. whenever I power up the VM it start the boot process and goes until I get error "(probe24:mps0:0:33:0): SCSI Status: Busy" and then immediately reboots. My setup and specs are below. I have the EXP3000 Plugged in to the LSI SAS9211-8i with using a single cable to the 'in' port on one of the ESM modules. The vm will keeping rebooting at the same point over and over. If I unplug the Sas cable connecting the enclosure the vm will boot fine. If I wait until Freenas finishes booting I can plug the SAS cable back in and then import the pool and everything runs fine until I need to reboot again. I attached a photo of the error which more details. Any thoughts here? Side note all disks are reported as healthy within freenas when I plug in the enclosure after letting it boot up. I'd really love to figure this out as I remote in to my lab to find myself rebooting a lot(self inflicted) and can't always unplug sas cable during boot.
VM Specs:
6vCPUS
12 GB Memory
LSI SAS9211-8i directly passthrough to VM
Specs:
IBM X3650 M3:
- 2x Xeon X5650 2.67Ghz 6c/12t
- 72GB DDR3 Reg ECC memory
- LSI MegaRaid M1015
- 3x SFF 146GB 10K SAS drives (RAID5, ESX Boot drive)
- LSI SAS9211-8I (flashed to IT mode)
- IBM EXP3000 SAS storage enclosure:
-12x 1TB LFF IBM 7.2K SAS drives
I just had the board fail in my stand alone system for freenas and now for a couple months until I can upgrade that I need to move Freenas to a VM with Passthrough. I am on ESXI 6.7 and running freenas 11.2u4. whenever I power up the VM it start the boot process and goes until I get error "(probe24:mps0:0:33:0): SCSI Status: Busy" and then immediately reboots. My setup and specs are below. I have the EXP3000 Plugged in to the LSI SAS9211-8i with using a single cable to the 'in' port on one of the ESM modules. The vm will keeping rebooting at the same point over and over. If I unplug the Sas cable connecting the enclosure the vm will boot fine. If I wait until Freenas finishes booting I can plug the SAS cable back in and then import the pool and everything runs fine until I need to reboot again. I attached a photo of the error which more details. Any thoughts here? Side note all disks are reported as healthy within freenas when I plug in the enclosure after letting it boot up. I'd really love to figure this out as I remote in to my lab to find myself rebooting a lot(self inflicted) and can't always unplug sas cable during boot.
VM Specs:
6vCPUS
12 GB Memory
LSI SAS9211-8i directly passthrough to VM
Specs:
IBM X3650 M3:
- 2x Xeon X5650 2.67Ghz 6c/12t
- 72GB DDR3 Reg ECC memory
- LSI MegaRaid M1015
- 3x SFF 146GB 10K SAS drives (RAID5, ESX Boot drive)
- LSI SAS9211-8I (flashed to IT mode)
- IBM EXP3000 SAS storage enclosure:
-12x 1TB LFF IBM 7.2K SAS drives