ATA Error Count Very High

Status
Not open for further replies.

twillkickers

Dabbler
Joined
Jun 3, 2017
Messages
19
I am running Freenas 11.1-Stable.

I have recently got alerts that both drives in my array seem to have an unusually high error count. I am new to this whole NAS thing and so my knowledge is very limited. Should I be concerned? What might be causing my errors? I have placed smartctl -a output for both of my drives below. I appreciate any help! (Sorry for my limited knowledge.)

Output of smartctl -a for first drive:
Code:
=== START OF INFORMATION SECTION ===
Model Family:	 Western Digital Black
Device Model:	 WDC WD5001FZWX-00ZHUA0
Serial Number:	WD-WX31DC46JJUF
LU WWN Device Id: 5 0014ee 0041be98d
Firmware Version: 01.01A01
User Capacity:	5,000,981,078,016 bytes [5.00 TB]
Sector Sizes:	 512 bytes logical, 4096 bytes physical
Rotation Rate:	7200 rpm
Form Factor:	  3.5 inches
Device is:		In smartctl database [for details use: -P show]
ATA Version is:   ACS-3 T13/2161-D revision 5
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:	Sun May  6 11:21:14 2018 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x84) Offline data collection activity
										was suspended by an interrupting command from host.
										Auto Offline Data Collection: Enabled.
Self-test execution status:	  (  41) The self-test routine was interrupted
										by the host with a hard or soft reset.
Total time to complete Offline
data collection:				(   90) seconds.
Offline data collection
capabilities:					(0x7b) SMART execute Offline immediate.
										Auto Offline data collection on/off support.
										Suspend Offline collection upon new
										command.
										Offline surface scan supported.
										Self-test supported.
										Conveyance Self-test supported.
										Selective Self-test supported.
SMART capabilities:			(0x0003) Saves SMART data before entering
										power-saving mode.
										Supports SMART auto save timer.
Error logging capability:		(0x01) Error logging supported.
										General Purpose Logging supported.
Short self-test routine
recommended polling time:		(   2) minutes.
Extended self-test routine
recommended polling time:		( 542) minutes.
Conveyance self-test routine
recommended polling time:		(   6) minutes.
SCT capabilities:			  (0x003d) SCT Status supported.
										SCT Error Recovery Control supported.
										SCT Feature Control supported.
										SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME		  FLAG	 VALUE WORST THRESH TYPE	  UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate	 0x002f   200   100   051	Pre-fail  Always	   -	   0
  3 Spin_Up_Time			0x0027   229   100   021	Pre-fail  Always	   -	   7541
  4 Start_Stop_Count		0x0032   099   099   000	Old_age   Always	   -	   1944
  5 Reallocated_Sector_Ct   0x0033   200   200   140	Pre-fail  Always	   -	   0
  7 Seek_Error_Rate		 0x002e   200   100   000	Old_age   Always	   -	   0
  9 Power_On_Hours		  0x0032   075   075   000	Old_age   Always	   -	   18518
 10 Spin_Retry_Count		0x0032   100   100   000	Old_age   Always	   -	   0
 11 Calibration_Retry_Count 0x0032   100   100   000	Old_age   Always	   -	   0
 12 Power_Cycle_Count	   0x0032   100   100   000	Old_age   Always	   -	   148
192 Power-Off_Retract_Count 0x0032   200   100   000	Old_age   Always	   -	   94
193 Load_Cycle_Count		0x0032   200   100   000	Old_age   Always	   -	   1850
194 Temperature_Celsius	 0x0022   106   097   000	Old_age   Always	   -	   46
196 Reallocated_Event_Count 0x0032   200   100   000	Old_age   Always	   -	   0
197 Current_Pending_Sector  0x0032   200   100   000	Old_age   Always	   -	   0
198 Offline_Uncorrectable   0x0030   200   100   000	Old_age   Offline	  -	   0
199 UDMA_CRC_Error_Count	0x0032   200   200   000	Old_age   Always	   -	   0
200 Multi_Zone_Error_Rate   0x0008   200   100   000	Old_age   Offline	  -	   0

SMART Error Log Version: 1
ATA Error Count: 209 (device log contains only the most recent five errors)
		CR = Command Register [HEX]
		FR = Features Register [HEX]
		SC = Sector Count Register [HEX]
		SN = Sector Number Register [HEX]
		CL = Cylinder Low Register [HEX]
		CH = Cylinder High Register [HEX]
		DH = Device/Head Register [HEX]
		DC = Device Command Register [HEX]
		ER = Error register [HEX]
		ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 209 occurred at disk power-on lifetime: 18507 hours (771 days + 3 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 41 10 88 75 d2 40  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------

Error 208 occurred at disk power-on lifetime: 18507 hours (771 days + 3 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 41 50 80 39 d0 40  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------

Error 207 occurred at disk power-on lifetime: 18414 hours (767 days + 6 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 41 f0 f8 56 86 40  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------

Error 206 occurred at disk power-on lifetime: 18172 hours (757 days + 4 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 51 06 32 c7 71 01  Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ef 10 06 00 00 00 00 00  34d+02:41:59.482  SET FEATURES [Enable SATA feature]

Error 205 occurred at disk power-on lifetime: 18158 hours (756 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 51 06 32 c7 71 01  Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ef 10 06 00 00 00 00 00  33d+13:09:34.957  SET FEATURES [Enable SATA feature]

SMART Self-test log structure revision number 1
Num  Test_Description	Status				  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline	Interrupted (host reset)	  90%	 18507		 -
# 2  Extended offline	Completed without error	   00%	 14473		 -
# 3  Short offline	   Completed without error	   00%	 14441		 -
# 4  Extended offline	Completed without error	   00%	 14430		 -
# 5  Short offline	   Completed without error	   00%	 14421		 -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
	1		0		0  Not_testing
	2		0		0  Not_testing
	3		0		0  Not_testing
	4		0		0  Not_testing
	5		0		0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.



Output of smartctl -a for second drive:
Code:
=== START OF INFORMATION SECTION ===
Model Family:	 Western Digital Black
Device Model:	 WDC WD5001FZWX-00ZHUA0
Serial Number:	WD-WX21D955YUA1
LU WWN Device Id: 5 0014ee 0aec7d3e0
Firmware Version: 01.01A01
User Capacity:	5,000,981,078,016 bytes [5.00 TB]
Sector Sizes:	 512 bytes logical, 4096 bytes physical
Rotation Rate:	7200 rpm
Form Factor:	  3.5 inches
Device is:		In smartctl database [for details use: -P show]
ATA Version is:   ACS-3 T13/2161-D revision 5
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:	Sun May  6 11:24:39 2018 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
										was completed without error.
										Auto Offline Data Collection: Enabled.
Self-test execution status:	  (  32) The self-test routine was interrupted
										by the host with a hard or soft reset.
Total time to complete Offline
data collection:				(   90) seconds.
Offline data collection
capabilities:					(0x7b) SMART execute Offline immediate.
										Auto Offline data collection on/off support.
										Suspend Offline collection upon new
										command.
										Offline surface scan supported.
										Self-test supported.
										Conveyance Self-test supported.
										Selective Self-test supported.
SMART capabilities:			(0x0003) Saves SMART data before entering
										power-saving mode.
										Supports SMART auto save timer.
Error logging capability:		(0x01) Error logging supported.
										General Purpose Logging supported.
Short self-test routine
recommended polling time:		(   2) minutes.
Extended self-test routine
recommended polling time:		( 559) minutes.
Conveyance self-test routine
recommended polling time:		(   6) minutes.
SCT capabilities:			  (0x003d) SCT Status supported.
										SCT Error Recovery Control supported.
										SCT Feature Control supported.
										SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME		  FLAG	 VALUE WORST THRESH TYPE	  UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate	 0x002f   200   100   051	Pre-fail  Always	   -	   0
  3 Spin_Up_Time			0x0027   229   100   021	Pre-fail  Always	   -	   7533
  4 Start_Stop_Count		0x0032   099   099   000	Old_age   Always	   -	   1028
  5 Reallocated_Sector_Ct   0x0033   200   200   140	Pre-fail  Always	   -	   0
  7 Seek_Error_Rate		 0x002e   200   100   000	Old_age   Always	   -	   0
  9 Power_On_Hours		  0x0032   076   076   000	Old_age   Always	   -	   17763
 10 Spin_Retry_Count		0x0032   100   100   000	Old_age   Always	   -	   0
 11 Calibration_Retry_Count 0x0032   100   100   000	Old_age   Always	   -	   0
 12 Power_Cycle_Count	   0x0032   100   100   000	Old_age   Always	   -	   144
192 Power-Off_Retract_Count 0x0032   200   100   000	Old_age   Always	   -	   85
193 Load_Cycle_Count		0x0032   200   100   000	Old_age   Always	   -	   943
194 Temperature_Celsius	 0x0022   108   098   000	Old_age   Always	   -	   44
196 Reallocated_Event_Count 0x0032   200   100   000	Old_age   Always	   -	   0
197 Current_Pending_Sector  0x0032   200   100   000	Old_age   Always	   -	   0
198 Offline_Uncorrectable   0x0030   200   100   000	Old_age   Offline	  -	   0
199 UDMA_CRC_Error_Count	0x0032   200   200   000	Old_age   Always	   -	   0
200 Multi_Zone_Error_Rate   0x0008   200   100   000	Old_age   Offline	  -	   0

SMART Error Log Version: 1
ATA Error Count: 1426 (device log contains only the most recent five errors)
		CR = Command Register [HEX]
		FR = Features Register [HEX]
		SC = Sector Count Register [HEX]
		SN = Sector Number Register [HEX]
		CL = Cylinder Low Register [HEX]
		CH = Cylinder High Register [HEX]
		DH = Device/Head Register [HEX]
		DC = Device Command Register [HEX]
		ER = Error register [HEX]
		ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1426 occurred at disk power-on lifetime: 17706 hours (737 days + 18 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 41 08 30 f8 a4 40  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------

Error 1425 occurred at disk power-on lifetime: 17417 hours (725 days + 17 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 51 00 00 00 00 00  Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------

Error 1424 occurred at disk power-on lifetime: 17417 hours (725 days + 17 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 51 00 00 00 00 00  Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------

Error 1423 occurred at disk power-on lifetime: 17417 hours (725 days + 17 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 51 00 00 00 00 00  Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------

Error 1422 occurred at disk power-on lifetime: 17417 hours (725 days + 17 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 51 00 00 00 00 00  Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------

SMART Self-test log structure revision number 1
Num  Test_Description	Status				  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline	Interrupted (host reset)	  00%		 0		 -
# 2  Extended offline	Completed without error	   00%	 13698		 -
# 3  Short offline	   Completed without error	   00%	 13686		 -
# 4  Extended offline	Completed without error	   00%	 13675		 -
# 5  Short offline	   Completed without error	   00%	 13665		 -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
	1		0		0  Not_testing
	2		0		0  Not_testing
	3		0		0  Not_testing
	4		0		0  Not_testing
	5		0		0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


What might be going on? I am using Western Digital Black drives, are these inappropriate for RAID storage? Once again, thanks for any help.
 

Ericloewe

Server Wrangler
Moderator
Joined
Feb 15, 2014
Messages
20,176
What's the output of smartctl -x /dev/whatever?
 

twillkickers

Dabbler
Joined
Jun 3, 2017
Messages
19
What's the output of smartctl -x /dev/whatever?

See below for smartctl -x /dev/ada1:
Code:
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.1-STABLE amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:	 Western Digital Black
Device Model:	 WDC WD5001FZWX-00ZHUA0
Serial Number:	WD-WX31DC46JJUF
LU WWN Device Id: 5 0014ee 0041be98d
Firmware Version: 01.01A01
User Capacity:	5,000,981,078,016 bytes [5.00 TB]
Sector Sizes:	 512 bytes logical, 4096 bytes physical
Rotation Rate:	7200 rpm
Form Factor:	  3.5 inches
Device is:		In smartctl database [for details use: -P show]
ATA Version is:   ACS-3 T13/2161-D revision 5
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:	Sun May  6 12:43:05 2018 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Disabled
ATA Security is:  Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x84) Offline data collection activity
										was suspended by an interrupting command from host.
										Auto Offline Data Collection: Enabled.
Self-test execution status:	  (  41) The self-test routine was interrupted
										by the host with a hard or soft reset.
Total time to complete Offline
data collection:				(   90) seconds.
Offline data collection
capabilities:					(0x7b) SMART execute Offline immediate.
										Auto Offline data collection on/off support.
										Suspend Offline collection upon new
										command.
										Offline surface scan supported.
										Self-test supported.
										Conveyance Self-test supported.
										Selective Self-test supported.
SMART capabilities:			(0x0003) Saves SMART data before entering
										power-saving mode.
										Supports SMART auto save timer.
Error logging capability:		(0x01) Error logging supported.
										General Purpose Logging supported.
Short self-test routine
recommended polling time:		(   2) minutes.
Extended self-test routine
recommended polling time:		( 542) minutes.
Conveyance self-test routine
recommended polling time:		(   6) minutes.
SCT capabilities:			  (0x003d) SCT Status supported.
										SCT Error Recovery Control supported.
										SCT Feature Control supported.
										SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME		  FLAGS	VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate	 POSR-K   200   100   051	-	0
  3 Spin_Up_Time			POS--K   229   100   021	-	7541
  4 Start_Stop_Count		-O--CK   099   099   000	-	1944
  5 Reallocated_Sector_Ct   PO--CK   200   200   140	-	0
  7 Seek_Error_Rate		 -OSR-K   200   100   000	-	0
  9 Power_On_Hours		  -O--CK   075   075   000	-	18519
 10 Spin_Retry_Count		-O--CK   100   100   000	-	0
 11 Calibration_Retry_Count -O--CK   100   100   000	-	0
 12 Power_Cycle_Count	   -O--CK   100   100   000	-	148
192 Power-Off_Retract_Count -O--CK   200   100   000	-	94
193 Load_Cycle_Count		-O--CK   200   100   000	-	1850
194 Temperature_Celsius	 -O---K   106   097   000	-	46
196 Reallocated_Event_Count -O--CK   200   100   000	-	0
197 Current_Pending_Sector  -O--CK   200   100   000	-	0
198 Offline_Uncorrectable   ----CK   200   100   000	-	0
199 UDMA_CRC_Error_Count	-O--CK   200   200   000	-	0
200 Multi_Zone_Error_Rate   ---R--   200   100   000	-	0
							||||||_ K auto-keep
							|||||__ C event count
							||||___ R error rate
							|||____ S speed/performance
							||_____ O updated online
							|______ P prefailure warning

General Purpose Log Directory Version 1
SMART		   Log Directory Version 1 [multi-sector log support]
Address	Access  R/W   Size  Description
0x00	   GPL,SL  R/O	  1  Log Directory
0x01		   SL  R/O	  1  Summary SMART error log
0x02		   SL  R/O	  5  Comprehensive SMART error log
0x03	   GPL	 R/O	  6  Ext. Comprehensive SMART error log
0x04	   GPL,SL  R/O	  8  Device Statistics log
0x06		   SL  R/O	  1  SMART self-test log
0x07	   GPL	 R/O	  1  Extended self-test log
0x09		   SL  R/W	  1  Selective self-test log
0x0a	   GPL	 R/W	  8  Device Statistics Notification
0x10	   GPL	 R/O	  1  NCQ Command Error log
0x11	   GPL	 R/O	  1  SATA Phy Event Counters log
0x12	   GPL	 R/O	  1  SATA NCQ Non-Data log
0x13	   GPL	 R/O	  1  SATA NCQ Send and Receive log
0x24	   GPL	 R/O	171  Current Device Internal Status Data log
0x30	   GPL,SL  R/O	  9  IDENTIFY DEVICE data log
0x80-0x9f  GPL,SL  R/W	 16  Host vendor specific log
0xa0-0xaf  GPL,SL  VS	  16  Device vendor specific log
0xb0	   GPL,SL  VS	   1  Device vendor specific log
0xb1-0xb5  GPL,SL  VS	  16  Device vendor specific log
0xb6		   SL  VS	  16  Device vendor specific log
0xb7	   GPL,SL  VS	  40  Device vendor specific log
0xb8-0xbf  GPL,SL  VS	  16  Device vendor specific log
0xc0	   GPL,SL  VS	   1  Device vendor specific log
0xde	   GPL	 VS	5502  Device vendor specific log
0xe0	   GPL,SL  R/W	  1  SCT Command/Status
0xe1	   GPL,SL  R/W	  1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 248 (device log contains only the most recent 24 errors)
		CR	 = Command Register
		FEATR  = Features Register
		COUNT  = Count (was: Sector Count) Register
		LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
		LH	 = LBA High (was: Cylinder High) Register	]   LBA
		LM	 = LBA Mid (was: Cylinder Low) Register	  ] Register
		LL	 = LBA Low (was: Sector Number) Register	 ]
		DV	 = Device (was: Device/Head) Register
		DC	 = Device Control Register
		ER	 = Error register
		ST	 = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 248 [7] occurred at disk power-on lifetime: 18507 hours (771 days + 3 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 10 00 00 13 d2 75 88 40 00  Error:

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------

Error 247 [6] occurred at disk power-on lifetime: 18507 hours (771 days + 3 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 50 00 00 13 d0 39 80 40 00  Error:

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------

Error 246 [5] occurred at disk power-on lifetime: 18487 hours (770 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 08 00 02 3e fd ff 80 40 00  Error: UNC at LBA = 0x23efdff80 = 9646768000

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 60 00 02 3e fd ff 80 40 00 47d+05:29:34.829  READ FPDMA QUEUED
  60 00 08 00 58 00 02 3e fd ff c8 40 08	 00:02:16.534  READ FPDMA QUEUED
  60 00 08 00 50 00 02 3e fd ff 58 40 08	 00:02:16.534  READ FPDMA QUEUED
  61 00 c8 00 48 00 02 42 36 36 a8 40 08	 00:02:16.534  WRITE FPDMA QUEUED
  61 00 c8 00 40 00 02 42 36 35 e0 40 08	 00:02:16.534  WRITE FPDMA QUEUED

Error 245 [4] occurred at disk power-on lifetime: 18414 hours (767 days + 6 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 f0 00 02 3a 86 56 f8 40 00  Error:

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------

Error 244 [3] occurred at disk power-on lifetime: 18172 hours (757 days + 4 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  04 -- 51 00 06 00 00 01 71 c7 32 01 00  Error: ABRT

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  ef 00 10 00 06 00 00 00 00 00 00 00 00 34d+02:41:59.482  SET FEATURES [Enable SATA feature]

Error 243 [2] occurred at disk power-on lifetime: 18158 hours (756 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  04 -- 51 00 06 00 00 01 71 c7 32 01 00  Error: ABRT

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  ef 00 10 00 06 00 00 00 00 00 00 00 00 33d+13:09:34.957  SET FEATURES [Enable SATA feature]

Error 242 [1] occurred at disk power-on lifetime: 18152 hours (756 days + 8 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 01 00 00 01 d4 74 0e 80 40 00  Error:

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------

Error 241 [0] occurred at disk power-on lifetime: 18151 hours (756 days + 7 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 08 00 02 28 74 c9 60 40 00  Error:

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description	Status				  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline	Interrupted (host reset)	  90%	 18507		 -
# 2  Extended offline	Completed without error	   00%	 14473		 -
# 3  Short offline	   Completed without error	   00%	 14441		 -
# 4  Extended offline	Completed without error	   00%	 14430		 -
# 5  Short offline	   Completed without error	   00%	 14421		 -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
	1		0		0  Not_testing
	2		0		0  Not_testing
	3		0		0  Not_testing
	4		0		0  Not_testing
	5		0		0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:				  3
SCT Version (vendor specific):	   258 (0x0102)
SCT Support Level:				   1
Device State:						Active (0)
Current Temperature:					46 Celsius
Power Cycle Min/Max Temperature:	 46/49 Celsius
Lifetime	Min/Max Temperature:	 14/55 Celsius
Under/Over Temperature Limit Count:   0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version:	 2
Temperature Sampling Period:		 1 minute
Temperature Logging Interval:		1 minute
Min/Max recommended Temperature:	  0/60 Celsius
Min/Max Temperature Limit:		   -41/85 Celsius
Temperature History Size (Index):	478 (352)

Index	Estimated Time   Temperature Celsius
 353	2018-05-06 04:46	49  ******************************
 ...	..(109 skipped).	..  ******************************
 463	2018-05-06 06:36	49  ******************************
 464	2018-05-06 06:37	48  *****************************
 ...	..( 10 skipped).	..  *****************************
 475	2018-05-06 06:48	48  *****************************
 476	2018-05-06 06:49	47  ****************************
 ...	..( 32 skipped).	..  ****************************
  31	2018-05-06 07:22	47  ****************************
  32	2018-05-06 07:23	46  ***************************
 ...	..(319 skipped).	..  ***************************
 352	2018-05-06 12:43	46  ***************************

SCT Error Recovery Control:
		   Read:	 70 (7.0 seconds)
		  Write:	 70 (7.0 seconds)

Device Statistics (GP Log 0x04)
Page  Offset Size		Value Flags Description
0x01  =====  =			   =  ===  == General Statistics (rev 1) ==
0x01  0x008  4			 148  -D-  Lifetime Power-On Resets
0x01  0x010  4		   18519  -D-  Power-on Hours
0x01  0x018  6	 43615678627  -D-  Logical Sectors Written
0x01  0x020  6	   364103947  -D-  Number of Write Commands
0x01  0x028  6	188467003862  -D-  Logical Sectors Read
0x01  0x030  6	   896882918  -D-  Number of Read Commands
0x01  0x038  6	  2243890560  -D-  Date and Time TimeStamp
0x01  0x048  2			1320  ND-  Workload Utilization
0x03  =====  =			   =  ===  == Rotating Media Statistics (rev 1) ==
0x03  0x008  4		   16675  -D-  Spindle Motor Power-on Hours
0x03  0x010  4		   16675  -D-  Head Flying Hours
0x03  0x018  4			1945  -D-  Head Load Events
0x03  0x020  4			 200  ND-  Number of Reallocated Logical Sectors
0x03  0x028  4			   0  -D-  Read Recovery Attempts
0x03  0x030  4			   0  -D-  Number of Mechanical Start Failures
0x03  0x038  4			   0  -D-  Number of Realloc. Candidate Logical Sectors
0x03  0x040  4			  94  -D-  Number of High Priority Unload Events
0x04  =====  =			   =  ===  == General Errors Statistics (rev 1) ==
0x04  0x008  4			   0  -D-  Number of Reported Uncorrectable Errors
0x04  0x010  4		   23574  -D-  Resets Between Cmd Acceptance and Completion
0x05  =====  =			   =  ===  == Temperature Statistics (rev 1) ==
0x05  0x008  1			  46  -D-  Current Temperature
0x05  0x010  1			  46  -D-  Average Short Term Temperature
0x05  0x018  1			  44  -D-  Average Long Term Temperature
0x05  0x020  1			  55  -D-  Highest Temperature
0x05  0x028  1			  14  -D-  Lowest Temperature
0x05  0x030  1			  51  -D-  Highest Average Short Term Temperature
0x05  0x038  1			  17  -D-  Lowest Average Short Term Temperature
0x05  0x040  1			  49  -D-  Highest Average Long Term Temperature
0x05  0x048  1			  28  -D-  Lowest Average Long Term Temperature
0x05  0x050  4			   0  -D-  Time in Over-Temperature
0x05  0x058  1			  60  -D-  Specified Maximum Operating Temperature
0x05  0x060  4			   0  -D-  Time in Under-Temperature
0x05  0x068  1			   0  -D-  Specified Minimum Operating Temperature
0x06  =====  =			   =  ===  == Transport Statistics (rev 1) ==
0x06  0x008  4		   30601  -D-  Number of Hardware Resets
0x06  0x010  4			 827  -D-  Number of ASR Events
0x06  0x018  4			   1  -D-  Number of Interface CRC Errors
								|||_ C monitored condition met
								||__ D supports DSN
								|___ N normalized value

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID	  Size	 Value  Description
0x0001  2			0  Command failed due to ICRC error
0x0002  2			0  R_ERR response for data FIS
0x0003  2			0  R_ERR response for device-to-host data FIS
0x0004  2			0  R_ERR response for host-to-device data FIS
0x0005  2			0  R_ERR response for non-data FIS
0x0006  2			0  R_ERR response for device-to-host non-data FIS
0x0007  2			0  R_ERR response for host-to-device non-data FIS
0x0008  2			0  Device-to-host non-data FIS retries
0x0009  2			0  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2			1  Device-to-host register FISes sent due to a COMRESET
0x000b  2			0  CRC errors within host-to-device FIS
0x000d  2			0  Non-CRC errors within host-to-device FIS
0x000f  2			0  R_ERR response for host-to-device data FIS, CRC
0x0012  2			0  R_ERR response for host-to-device non-data FIS, CRC
0x8000  4			0  Vendor specific


See next post for ada2!
 

twillkickers

Dabbler
Joined
Jun 3, 2017
Messages
19
See below for smartctl -x /dev/ada2:
Code:
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.1-STABLE amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:	 Western Digital Black
Device Model:	 WDC WD5001FZWX-00ZHUA0
Serial Number:	WD-WX21D955YUA1
LU WWN Device Id: 5 0014ee 0aec7d3e0
Firmware Version: 01.01A01
User Capacity:	5,000,981,078,016 bytes [5.00 TB]
Sector Sizes:	 512 bytes logical, 4096 bytes physical
Rotation Rate:	7200 rpm
Form Factor:	  3.5 inches
Device is:		In smartctl database [for details use: -P show]
ATA Version is:   ACS-3 T13/2161-D revision 5
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:	Sun May  6 12:45:14 2018 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Disabled
ATA Security is:  Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
										was completed without error.
										Auto Offline Data Collection: Enabled.
Self-test execution status:	  (  32) The self-test routine was interrupted
										by the host with a hard or soft reset.
Total time to complete Offline
data collection:				(   90) seconds.
Offline data collection
capabilities:					(0x7b) SMART execute Offline immediate.
										Auto Offline data collection on/off support.
										Suspend Offline collection upon new
										command.
										Offline surface scan supported.
										Self-test supported.
										Conveyance Self-test supported.
										Selective Self-test supported.
SMART capabilities:			(0x0003) Saves SMART data before entering
										power-saving mode.
										Supports SMART auto save timer.
Error logging capability:		(0x01) Error logging supported.
										General Purpose Logging supported.
Short self-test routine
recommended polling time:		(   2) minutes.
Extended self-test routine
recommended polling time:		( 559) minutes.
Conveyance self-test routine
recommended polling time:		(   6) minutes.
SCT capabilities:			  (0x003d) SCT Status supported.
										SCT Error Recovery Control supported.
										SCT Feature Control supported.
										SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME		  FLAGS	VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate	 POSR-K   200   100   051	-	0
  3 Spin_Up_Time			POS--K   229   100   021	-	7533
  4 Start_Stop_Count		-O--CK   099   099   000	-	1028
  5 Reallocated_Sector_Ct   PO--CK   200   200   140	-	0
  7 Seek_Error_Rate		 -OSR-K   200   100   000	-	0
  9 Power_On_Hours		  -O--CK   076   076   000	-	17764
 10 Spin_Retry_Count		-O--CK   100   100   000	-	0
 11 Calibration_Retry_Count -O--CK   100   100   000	-	0
 12 Power_Cycle_Count	   -O--CK   100   100   000	-	144
192 Power-Off_Retract_Count -O--CK   200   100   000	-	85
193 Load_Cycle_Count		-O--CK   200   100   000	-	943
194 Temperature_Celsius	 -O---K   108   098   000	-	44
196 Reallocated_Event_Count -O--CK   200   100   000	-	0
197 Current_Pending_Sector  -O--CK   200   100   000	-	0
198 Offline_Uncorrectable   ----CK   200   100   000	-	0
199 UDMA_CRC_Error_Count	-O--CK   200   200   000	-	0
200 Multi_Zone_Error_Rate   ---R--   200   100   000	-	0
							||||||_ K auto-keep
							|||||__ C event count
							||||___ R error rate
							|||____ S speed/performance
							||_____ O updated online
							|______ P prefailure warning

General Purpose Log Directory Version 1
SMART		   Log Directory Version 1 [multi-sector log support]
Address	Access  R/W   Size  Description
0x00	   GPL,SL  R/O	  1  Log Directory
0x01		   SL  R/O	  1  Summary SMART error log
0x02		   SL  R/O	  5  Comprehensive SMART error log
0x03	   GPL	 R/O	  6  Ext. Comprehensive SMART error log
0x04	   GPL,SL  R/O	  8  Device Statistics log
0x06		   SL  R/O	  1  SMART self-test log
0x07	   GPL	 R/O	  1  Extended self-test log
0x09		   SL  R/W	  1  Selective self-test log
0x0a	   GPL	 R/W	  8  Device Statistics Notification
0x10	   GPL	 R/O	  1  NCQ Command Error log
0x11	   GPL	 R/O	  1  SATA Phy Event Counters log
0x12	   GPL	 R/O	  1  SATA NCQ Non-Data log
0x13	   GPL	 R/O	  1  SATA NCQ Send and Receive log
0x24	   GPL	 R/O	171  Current Device Internal Status Data log
0x30	   GPL,SL  R/O	  9  IDENTIFY DEVICE data log
0x80-0x9f  GPL,SL  R/W	 16  Host vendor specific log
0xa0-0xaf  GPL,SL  VS	  16  Device vendor specific log
0xb0	   GPL,SL  VS	   1  Device vendor specific log
0xb1-0xb5  GPL,SL  VS	  16  Device vendor specific log
0xb6		   SL  VS	  16  Device vendor specific log
0xb7	   GPL,SL  VS	  40  Device vendor specific log
0xb8-0xbf  GPL,SL  VS	  16  Device vendor specific log
0xc0	   GPL,SL  VS	   1  Device vendor specific log
0xde	   GPL	 VS	5502  Device vendor specific log
0xe0	   GPL,SL  R/W	  1  SCT Command/Status
0xe1	   GPL,SL  R/W	  1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 10753 (device log contains only the most recent 24 errors)
		CR	 = Command Register
		FEATR  = Features Register
		COUNT  = Count (was: Sector Count) Register
		LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
		LH	 = LBA High (was: Cylinder High) Register	]   LBA
		LM	 = LBA Mid (was: Cylinder Low) Register	  ] Register
		LL	 = LBA Low (was: Sector Number) Register	 ]
		DV	 = Device (was: Device/Head) Register
		DC	 = Device Control Register
		ER	 = Error register
		ST	 = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 10753 [0] occurred at disk power-on lifetime: 17706 hours (737 days + 18 hours)
  When the command that caused the error occurred, the device was in an unknown state.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 08 00 01 ef a4 f8 30 40 00  Error:

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------

Error 10752 [23] occurred at disk power-on lifetime: 17701 hours (737 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 41 00 08 00 00 00 40 04 78 40 00  Error: IDNF at LBA = 0x00400478 = 4195448

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 08 00 08 00 00 00 40 04 78 40 00 45d+22:45:24.347  WRITE FPDMA QUEUED
  61 00 08 00 00 00 00 00 40 02 78 40 08	 00:17:21.106  WRITE FPDMA QUEUED
  60 01 00 00 f8 00 00 50 a5 2c d0 40 08	 00:17:21.105  READ FPDMA QUEUED
  ea 00 00 00 00 00 00 00 00 00 00 40 08	 00:17:21.105  FLUSH CACHE EXT
  61 00 08 00 e8 00 02 40 d2 8f 68 40 08	 00:17:20.955  WRITE FPDMA QUEUED

Error 10751 [22] occurred at disk power-on lifetime: 17554 hours (731 days + 10 hours)
  When the command that caused the error occurred, the device was doing SMART Offline or Self-test.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 41 01 00 00 01 48 40 42 d8 40 00  Error: IDNF at LBA = 0x1484042d8 = 5507138264

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 01 00 00 f0 00 01 48 40 42 d8 40 00 39d+19:31:34.767  WRITE FPDMA QUEUED
  61 01 00 00 e8 00 01 48 40 41 d8 40 08	 00:51:00.906  WRITE FPDMA QUEUED
  61 01 00 00 e0 00 01 48 40 40 d8 40 08	 00:51:00.906  WRITE FPDMA QUEUED
  61 01 00 00 d8 00 01 48 40 3f d8 40 08	 00:51:00.906  WRITE FPDMA QUEUED
  61 00 a0 00 d0 00 01 48 40 2b 60 40 08	 00:51:00.905  WRITE FPDMA QUEUED

Error 10750 [21] occurred at disk power-on lifetime: 17417 hours (725 days + 17 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 01 00 00 02 34 91 bc 78 40 00  Error: UNC at LBA = 0x23491bc78 = 9471900792

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 18 00 02 34 91 bc 78 40 00 34d+03:07:03.940  READ FPDMA QUEUED
  60 01 00 00 10 00 02 34 91 bb 78 40 08	 00:18:44.584  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 00 08	 00:18:44.584  READ LOG EXT
  60 01 00 00 d0 00 02 34 91 bc 78 40 08	 00:18:37.334  READ FPDMA QUEUED
  60 01 00 00 c8 00 02 34 91 bb 78 40 08	 00:18:37.334  READ FPDMA QUEUED

Error 10749 [20] occurred at disk power-on lifetime: 17417 hours (725 days + 17 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 01 00 00 02 34 91 bb 78 40 00  Error: UNC at LBA = 0x23491bb78 = 9471900536

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 c8 00 02 34 91 bb 78 40 00 34d+03:06:56.695  READ FPDMA QUEUED
  60 00 50 00 c0 00 02 34 91 ba 70 40 08	 00:18:37.334  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 00 08	 00:18:37.334  READ LOG EXT
  60 01 00 00 78 00 02 34 91 bb 78 40 08	 00:18:30.090  READ FPDMA QUEUED
  60 00 50 00 70 00 02 34 91 ba 70 40 08	 00:18:30.090  READ FPDMA QUEUED

Error 10748 [19] occurred at disk power-on lifetime: 17417 hours (725 days + 17 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 50 00 02 34 91 ba 70 40 00  Error: UNC at LBA = 0x23491ba70 = 9471900272

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 50 00 70 00 02 34 91 ba 70 40 00 34d+03:06:49.453  READ FPDMA QUEUED
  60 00 08 00 68 00 02 34 91 ba 80 40 08	 00:18:30.090  READ FPDMA QUEUED
  25 00 00 00 18 00 01 d8 4d 0a 10 40 08	 00:18:30.090  READ DMA EXT
  25 00 00 00 18 00 01 d8 4d 0a 10 40 08	 00:18:30.090  READ DMA EXT
  60 00 08 00 50 00 01 d8 4d 08 a8 40 08	 00:18:22.922  READ FPDMA QUEUED

Error 10747 [18] occurred at disk power-on lifetime: 17417 hours (725 days + 17 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 18 00 01 d8 4d 0a 10 40 00  Error: UNC 24 sectors at LBA = 0x1d84d0a10 = 7923894800

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 18 00 01 d8 4d 0a 10 40 00 34d+03:06:42.288  READ DMA EXT
  60 00 08 00 50 00 01 d8 4d 08 a8 40 08	 00:18:22.922  READ FPDMA QUEUED
  25 00 00 00 08 00 02 34 92 26 80 40 08	 00:18:22.922  READ DMA EXT
  60 00 28 00 40 00 01 d8 4d 09 38 40 08	 00:18:22.892  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 00 08	 00:18:22.892  READ LOG EXT

Error 10746 [17] occurred at disk power-on lifetime: 17417 hours (725 days + 17 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 28 00 01 d8 4d 09 38 40 00  Error: UNC at LBA = 0x1d84d0938 = 7923894584

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 28 00 30 00 01 d8 4d 09 38 40 00 34d+03:06:35.026  READ FPDMA QUEUED
  60 00 28 00 28 00 02 34 92 27 10 40 08	 00:18:15.551  READ FPDMA QUEUED
  2f 00 00 00 01 00 00 00 00 00 10 00 08	 00:18:15.551  READ LOG EXT
  60 00 28 00 18 00 01 d8 4d 09 38 40 08	 00:18:08.301  READ FPDMA QUEUED
  60 00 28 00 10 00 02 34 92 27 10 40 08	 00:18:08.301  READ FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description	Status				  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline	Interrupted (host reset)	  00%		 0		 -
# 2  Extended offline	Completed without error	   00%	 13698		 -
# 3  Short offline	   Completed without error	   00%	 13686		 -
# 4  Extended offline	Completed without error	   00%	 13675		 -
# 5  Short offline	   Completed without error	   00%	 13665		 -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
	1		0		0  Not_testing
	2		0		0  Not_testing
	3		0		0  Not_testing
	4		0		0  Not_testing
	5		0		0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:				  3
SCT Version (vendor specific):	   258 (0x0102)
SCT Support Level:				   1
Device State:						Active (0)
Current Temperature:					44 Celsius
Power Cycle Min/Max Temperature:	 44/48 Celsius
Lifetime	Min/Max Temperature:	 14/54 Celsius
Under/Over Temperature Limit Count:   0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version:	 2
Temperature Sampling Period:		 1 minute
Temperature Logging Interval:		1 minute
Min/Max recommended Temperature:	  0/60 Celsius
Min/Max Temperature Limit:		   -41/85 Celsius
Temperature History Size (Index):	478 (4)

Index	Estimated Time   Temperature Celsius
   5	2018-05-06 04:48	48  *****************************
 ...	..( 61 skipped).	..  *****************************
  67	2018-05-06 05:50	48  *****************************
  68	2018-05-06 05:51	47  ****************************
 ...	..( 52 skipped).	..  ****************************
 121	2018-05-06 06:44	47  ****************************
 122	2018-05-06 06:45	46  ***************************
 ...	..( 14 skipped).	..  ***************************
 137	2018-05-06 07:00	46  ***************************
 138	2018-05-06 07:01	45  **************************
 ...	..( 31 skipped).	..  **************************
 170	2018-05-06 07:33	45  **************************
 171	2018-05-06 07:34	44  *************************
 ...	..(310 skipped).	..  *************************
   4	2018-05-06 12:45	44  *************************

SCT Error Recovery Control:
		   Read:	 70 (7.0 seconds)
		  Write:	 70 (7.0 seconds)

Device Statistics (GP Log 0x04)
Page  Offset Size		Value Flags Description
0x01  =====  =			   =  ===  == General Statistics (rev 1) ==
0x01  0x008  4			 144  -D-  Lifetime Power-On Resets
0x01  0x010  4		   17764  -D-  Power-on Hours
0x01  0x018  6	 66181610686  -D-  Logical Sectors Written
0x01  0x020  6	   438791926  -D-  Number of Write Commands
0x01  0x028  6	124609061761  -D-  Logical Sectors Read
0x01  0x030  6	   555217118  -D-  Number of Read Commands
0x01  0x038  6	  3820857856  -D-  Date and Time TimeStamp
0x01  0x048  2			1085  ND-  Workload Utilization
0x03  =====  =			   =  ===  == Rotating Media Statistics (rev 1) ==
0x03  0x008  4		   13547  -D-  Spindle Motor Power-on Hours
0x03  0x010  4		   13547  -D-  Head Flying Hours
0x03  0x018  4			1029  -D-  Head Load Events
0x03  0x020  4			 200  ND-  Number of Reallocated Logical Sectors
0x03  0x028  4			 474  -D-  Read Recovery Attempts
0x03  0x030  4			   0  -D-  Number of Mechanical Start Failures
0x03  0x038  4			   0  -D-  Number of Realloc. Candidate Logical Sectors
0x03  0x040  4			  85  -D-  Number of High Priority Unload Events
0x04  =====  =			   =  ===  == General Errors Statistics (rev 1) ==
0x04  0x008  4			   0  -D-  Number of Reported Uncorrectable Errors
0x04  0x010  4		   18087  -D-  Resets Between Cmd Acceptance and Completion
0x05  =====  =			   =  ===  == Temperature Statistics (rev 1) ==
0x05  0x008  1			  44  -D-  Current Temperature
0x05  0x010  1			  45  -D-  Average Short Term Temperature
0x05  0x018  1			  43  -D-  Average Long Term Temperature
0x05  0x020  1			  54  -D-  Highest Temperature
0x05  0x028  1			  14  -D-  Lowest Temperature
0x05  0x030  1			  51  -D-  Highest Average Short Term Temperature
0x05  0x038  1			  17  -D-  Lowest Average Short Term Temperature
0x05  0x040  1			  49  -D-  Highest Average Long Term Temperature
0x05  0x048  1			  23  -D-  Lowest Average Long Term Temperature
0x05  0x050  4			   0  -D-  Time in Over-Temperature
0x05  0x058  1			  60  -D-  Specified Maximum Operating Temperature
0x05  0x060  4			   0  -D-  Time in Under-Temperature
0x05  0x068  1			   0  -D-  Specified Minimum Operating Temperature
0x06  =====  =			   =  ===  == Transport Statistics (rev 1) ==
0x06  0x008  4		   20115  -D-  Number of Hardware Resets
0x06  0x010  4			 665  -D-  Number of ASR Events
0x06  0x018  4			   0  -D-  Number of Interface CRC Errors
								|||_ C monitored condition met
								||__ D supports DSN
								|___ N normalized value

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID	  Size	 Value  Description
0x0001  2			0  Command failed due to ICRC error
0x0002  2			0  R_ERR response for data FIS
0x0003  2			0  R_ERR response for device-to-host data FIS
0x0004  2			0  R_ERR response for host-to-device data FIS
0x0005  2			0  R_ERR response for non-data FIS
0x0006  2			0  R_ERR response for device-to-host non-data FIS
0x0007  2			0  R_ERR response for host-to-device non-data FIS
0x0008  2			0  Device-to-host non-data FIS retries
0x0009  2			0  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2			1  Device-to-host register FISes sent due to a COMRESET
0x000b  2			0  CRC errors within host-to-device FIS
0x000d  2			0  Non-CRC errors within host-to-device FIS
0x000f  2			0  R_ERR response for host-to-device data FIS, CRC
0x0012  2			0  R_ERR response for host-to-device non-data FIS, CRC
0x8000  4			0  Vendor specific


Thanks again for your help!! :smile:
 

Ericloewe

Server Wrangler
Moderator
Joined
Feb 15, 2014
Messages
20,176
Your disks are reporting an unusually high number of hardware resets. If it were a single disk, I'd say replace it. With two disks, I'd investigate bad power. Failing PSU, dodgy cables, etc. At a minimum, reseat all power cables.
 

twillkickers

Dabbler
Joined
Jun 3, 2017
Messages
19
Your disks are reporting an unusually high number of hardware resets. If it were a single disk, I'd say replace it. With two disks, I'd investigate bad power. Failing PSU, dodgy cables, etc. At a minimum, reseat all power cables.

Thank you for your reply. I will re-seat all cables as soon as I can get to the physical server. Could these hardware resets cause damage to the disk over the long term?

In addition, my server is a Dell PowerEdge T30 Server, BTX, with a stock power supply. I have heard stock Dell power supplies tend to be on the cheap side, how likely do you think that is the root cause?
 

Ericloewe

Server Wrangler
Moderator
Joined
Feb 15, 2014
Messages
20,176

Jailer

Not strong, but bad
Joined
Sep 12, 2014
Messages
4,975
Your drives seem to be running awfully warm. Not sure if it would contribute to the problem but running them cooler than they currently are won't hurt.
 
Status
Not open for further replies.
Top