vnet

  1. rwfitzy

    Can't access iocage jail after 11.2 upgrade

    I just upgraded from 11.1-U7 to 11.2-U2.1 and all went well except this jail issue. It would not start until I went to the command line and received an error: root@nas1:~ # iocage start monitor monitor: bpf requires vnet=on! So I did iocage set vnet=on monitor and it started OK: root@nas1:~ #...
  2. D

    Plex/VNET not working

    Hi guys, So I moved from 9.10 to 11.2 today, all went fine, then basically went with a fresh install of plex, so I set up a new jail and then fresh installed plexpass in it. Then the issue is that plex won't play videos that need transcoding (direct play works fine) and also won't get any...
  3. itskando

    SOLVED What does VNET serve? Does Plex require a VNET?

    Someone in this thread suggested that I enable VNET for my Plex jail. (It didn't help my original issue and actually made things worse, but that was likely because I wasn't setting things up correctly.) It led me to look up VNETs and some other networking things. I didn't find much in the way...
  4. N

    VNET failure while installing a plugin.

    I'm new to FreeNAS and I am experiencing some problems since I always used NAS4Free for my servers. When installing any plugin with dhcp enabled (plugin setup/install page) I get the error: [EFAULT] Exception: RuntimeError: Stopped couchpotato due to VNET failure occured, destroyed...
  5. tuxbrother

    vnet Device bringt falsches Interface in die Bridge

    Hallo, noch neu bei der FreeNAS versuche ich zur Zeit eine Jail mit einem Interface über eine Bridge ans Netz zu bekommen. Die Bridge ist an ein 10GBe Interface gebunden. Doch sobald ich die Jail starte wird das erste Interface (über das FreeNAS mit der WebUI administriert wird) mit in die...
  6. lexxai

    When VNET devices ready is after start jail by iocage ?

    I want do isolate jail from jail by bridge private feature. I try set script as poststart option to jail: iocage set exec_poststart=/root/test/pstart.sh foo /root/test/pstart.sh: #!/bin/sh ifconfig bridge0 | grep member: |grep -v PRIVATE | awk '{ print $2 }' | grep 'vnet' | xargs ifconfig...
  7. whiskeyjack

    SOLVED How can I receive UDP multicast packets in an iocage jail?

    I'm running an Domoticz instance in an iocage jail without VNET enabled and I'm trying to get my Xioami sensors to work. They are added fine, but then never updated. This likely is because Domoticz inside the jail is not receiving the broadcast UDP packets. Running tcpdump -i em0 -n port 9898...
  8. F

    No networking in iocage jail after upgrade to 11.1 U5

    I upgraded to 11.1-U5 this morning, and after reboot found I had no networking to/from my jails - I couldn't ping them from outside, nor reach outside from within. After checking a few things, I noticed some differences in the networking setup from before the reboot. 1) The ethernet device on...
  9. P

    Iocage and IPv6 autoconf ?

    Hi, I have been unable to find an answer in the docs or using google. How are you supposed to configure an autoconf IPv6 address in an iocage jail ? I am using vnet jails and have been able to get it working manually by setting rtsold_enable=YES and starting rtsold service after the jail is...
  10. B

    Network problem with iocage jails

    Hello, I have a problem with my network configuration. At the moment, I have three jails (with iocage). igb0|192.168.178.11/24 -> git server igb0|192.168.178.12/24 -> nextcloud igb0|192.168.178.13/24 -> emby The IP of my FreeNAS system is igb0|192.168.178.10/24. I read the iocage documentation...
Top