smart

  1. dak180

    TrueNAS-Report 1.8

    ZPool, SMART, and UPS Status Report with TrueNAS Config Backup Original Script By: joeschmuck Modified By: bidelu0hm, melp, fohlsso2, onlinepcwizard, ninpucho, isentropik, rotx, dak180 Last Edited By: dak180 Current Version: v1.8 Preview of the output here: https://i.imgur.com/jKwraw4.png When...
  2. S

    Problem with SMART commands in a Dell SAS Perc H200A

    Hello, the first thing to say hello to you all since I just registered in the forum. I have a Dell PowerEdge T110 server with a Dell SAS Perc H200A controller that apparently works fine, since I have generated a 24Tb logical volume (6Tb x 4 hdd) and mount and access it without problem, but I...
  3. J

    Currently unreadable sectors (smartctl -t long no error)

    As you may have guessed from the title, I have a problem with a drive that says it has 22 currently unreadable sectors. It was a new drive when I installed it a couple of years ago and it has been running fine since. The unreadable sectors finally worried me enough to make a decent effort to...
  4. P

    ATA Error Count and Not Helpful SMART Info.

    Hardware/OS: WD 2TB - Western Digital Black - /dev/ada0 (additional drive we installed for zpool) WD 2TB - Western Digital Black - /dev/ada2 (additional drive we installed for zpool) 1TB - Seagate Barracuda 3.5 - /dev/ada1 (standard drive that comes in the Dell T310s we use) 8GB RAM Intel(R)...
  5. X

    11.2-U4 to 11.2-U5 SMART Temperature Issue

    After upgrading to 11.2-U5, I've lost the ability to read back drive temperature, all show as N/A, the SMARTD service is running though. Sort of at a bit of a loss on what might have happened or how to resolve it? SMART tests still run as far as I can tell, just no temperature graphs, no...
  6. jpi

    system reboot during volume creation of SAS SSDs (SSD then disappears)

    Hello, I bought two 800GB SAS SSDs and connected them to ports 12 and 13 on my R510 (yes, the internal 2.5" bays). I ran a short smart test on both of them and they look fine, been powered on ~4years but both have less than 1TB written or read to\from them. The first time I tried to create a...
  7. itskando

    Task Scheduling

    Does the following seem reasonable for a homeserver: Followed this guide. Day 01: scrub Day 08: SMART(long) Day 15: scrub Day 22: SMART(long) [4AM for all] [Scrubs: threshold: 10 days.] Day 05: SMART(short) Day 12: SMART(short) Day 19: SMART(short) Day 26: SMART(short) [3AM for all] Daily...
  8. PhiloEpisteme

    Running SMART tests on Samsung 970 EVO

    Hey folks, Apologies if there is a thread already related to this, I was unable to find it in my searches. My basic issue is that I am seemingly unable to run the short and long tests on my Samsung 970 EVO drives despite their website listing these drives as supporting SMART. This is a test...
  9. S

    SOLVED Failed drive not showing in GUI. Unable to view disk.

    Hi, I have a system where I used 4x 2TB Seagate Green disks. I have replaced 2 of the disks earlier, one with a similar one and one with a 4 TB WD Red. I've bought new WD 4 TB Red disks and were going to replace the rest, but haven't got there yet. Anyhow, yesterday I was tranfering a 20 GB...
  10. Stranded Camel

    Bug in FreeNAS smartmontools

    I've got a five-disk RAID Z2 array made up of WD Gold 10 TB disks that I've had running for about half a year under FreeNAS-11.1-U5. I noticed a while ago that not one of these disks has ever successfully completed a single SMART test. It doesn't matter if I run the tests under load or right...
  11. K

    Smartd does not start on H730P - empty smartd.conf

    Hello. On my Dell server I have PERC H730P Adapter switch to HBA. The smartd fails to start at boot and manually. /usr/local/etc/smartd.conf is empty I try turn off smart to da5 or add -d removable to S.M.A.R.T. extra options: - smartd fails to start. Try this on FreeNAS-11.1-U5 and current test...
  12. T

    S.M.A.R.T service will not start after 11.1 update

    I updated from FreeNAS 9.10 to 11.1-stable tonight and after the reboot, the dashboard flashes a message, in the top right-hand corner, when selecting it I see “- smartd_daemon is not running.” When going to the services tab in the webUI I click start for S.M.A.R.T while tailing...
  13. eexodus

    NetApp DS4243 and LSI 9201-16e missing SMART values

    I have a NetApp DS4243 with 14x 8TB WD Reds connected to a LSI 9201-16e via a QSFP+ to SAS cable inside a Dell PowerEdge R610. Whenever I pull the SMART status for these drives there's only a few values available, temp, power on count. Is it normal to have so little values? Should I be concerned...
  14. R

    Disks or HW Failing for DAS

    I've been running this DAS box for years now, and only after I upgraded to FreeNAS11 and now having problems (coincidence?). I have since detached the volume for da11-da21 and also removed another volume with 8? 8TB disks which have also been having issues (I think staying connected or even...
  15. A

    smartd_daemon is not running. Manually edited smartd.conf file

    I was getting the "WARNING smartd_daemon is not running" and even after unchecking the S.M.A.R.T. checkbox for the drives, I could still not start the S.M.A.R.T. service. I looked at the console and it was showing "freenas smartd: Configuration file /usr/local/etc/smartd.conf parsed but has no...
  16. C

    SOLVED Unable to complete enrypted drive unlock

    I began to notice very poor performance of my FreeNAS earlier today (taking ~20min to do an rsync dry run that would usually be done in 20 seconds). After trying a couple of times, I discovered that my previously unlocked encrypted volume had locked itself. When I try to unlock it, I get stuck...
  17. G

    SMART Service won't start, config empty?

    When the server starts or if I try to start SMART manually it doesn't start. The log shows: shade smartd[75867]: Configuration file /usr/local/etc/smartd.conf parsed but has no entries I've double checked and only the physical drives have SMART turned on, the usb drives do not. not sure what...
  18. BlakeNagel07

    SOLVED S.M.A.R.T. crashed, Not starting

    Freenas 11.1-U4 S.M.A.R.T. crashed and will not restart. I tried removing S.M.A.R.T. from the usb drive and it still not starting. System log says the following before and after removing SMART from the usb. "Server smartd [81374]: Unable to register device /dev/da0 (no Directive -d...
  19. Kennyvb8

    grinding noise - HDD

    Hello i have 6 HDD in raidz1-0 i think, and last night one of the disks startet makeing grinding noises, and still doing. Smart test shor/long all passes on all disks?!? so how do i figurer out which one is doing the noise? i have 2 new disks laying around i can easily replace 1-2 drives, but...
  20. S

    FreeNAS lockup’s - SMART failures

    Hi all I’ll give you a quick run down of my setup first: Virtualised freenas instance 8 sas drives used for the pool 32gb memory SATA dom for freenas os Pool setup in mirror / raid 10 equivalent Using NFS presented to ESXi hosts About once a week one particular drive gets SMART errors with...
  21. T

    Pool degraded - failed to read SMART Attribute Data

    FreeNAS 11.1-U3 Supermicro X11SSL-CF with six Toshiba DT01ACA3 drives connected to the LSI 3008 (FW PH15.00.03.00). I got a critical alert today: CRITICAL: March 24, 2018, 8:52 a.m. - Device: /dev/da3 [SAT], failed to read SMART Attribute Data CRITICAL: March 24, 2018, 8:48 a.m. - The volume...
  22. W

    Scrub und Smart Tests

    Hallo, ich habe mir einen Nas aus einem etwas älteren Server zusammengebaut. Ich wollte ihn so einstellen, dass er sich runterfährt, wenn kein PC gerade im lan ist und er hochfährt sobald einer drin ist. Das ist kein Problem. Das Problem sind jetzt die Test, was würdet ihr mir empfehlen, wie...
  23. paradoxiom

    Updating to 11.1-U1 breaks SMART for me.

    I updated, all was fine, then I read a post somewhere about SMART not being necessary to be turned on for the boot device (SD card/USB mirror), so I went to Storage>View Disks, clicked the boot device opened the window and unticked SMART, clicked ok, then I get some log message like...
  24. S

    smartctl attributes not displayed for SAS drives?

    I've tried to solve this via Google but not had any luck. The baseboard is Supermicro X10 Xeon and the SAS drives are connected via two LSI 9211 HBAs. When I run `smartctl -a /dev/XXX`, I get detailed attribute data for SATA HDDs only. I know that SCSI/SAS, and therefore smartctl, didn't...
  25. N

    Critical SMART alerts on both USB boot drives after upgrade to 11.1

    I upgraded to 11.1 today, and immediately after the upgrade I got critical alerts shown for both SanDisk Extreme 32GB USB Flash Drives I use as boot devices: CRITICAL: Dec. 27, 2017, 12:09 p.m. - Device: /dev/da1 [SAT], FAILED SMART self-check. BACK UP DATA NOW! CRITICAL: Dec. 27, 2017, 12:09...
  26. artix lumren

    SSD boot drive not added to smartd.conf

    Hello everyone, I'm testing my build to check that everything is working as expected. Here is the build : Supermicro X11SSL-F Intel Core i3-6100 Kingston Memory DDR4 16GB 2133MHz ECC Seasonic FOCUS Plus 550 Gold Samsung ssd 830 pro 128GB (Detected has 840) 2x WD Red - 3.5" SATA 6Gb/s - 6TB...
  27. G

    SMART Testing Information Question

    Hello Everyone, This might be mentioned elseware but a forum / google search didn't jump anything out at me. When using SMART test scheduling and manually calling via smartctl in the CLI. You can run smartctl -l selftest *drive* and it will output the results of the last test. However I...
  28. mattlach

    Scary SMART Values on New Seagate Enterprise Drives?

    Hey all, So, I'm 4 disks into my "swap all 12 drives in my NAS with larger drives and resilver to grow my ZFS pool" project, and decided to go with 10TB Seagate Helium Enterprise drives (ST10000NM0016) The four drives I have thus far come from two orders of two drives each. Two from Newegg...
  29. C

    HP H240 HBA Controller

    Hi, I have a HP DL 180 Gen 9 Server with H240 HBA card and I have enabled HBA mode. I can see all the disks directly getting attached to Freenas but the SMART function is not getting started. Can any one please help? Also If i run FreeNAS storage without SMART function will there be any...
  30. H

    SOLVED Pending sector

    Hi everyone, For a full week now my server has been warning me of an error concerning one of my drives. Apparently one of them has "1 currently unreadable (pending) sector". I had to look up what it actually meant, from what I understand now it is a sector which has not been reallocated yet and...
  31. gareththered

    SOLVED CAM Errors

    My dmesg shows the following (extract): (ada0:ahcich0:0:0:0): READ_FPDMA_QUEUED. ACB: 60 e0 a0 9e 50 40 5d 01 00 00 00 00 (ada0:ahcich0:0:0:0): CAM status: ATA Status Error (ada0:ahcich0:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC ) (ada0:ahcich0:0:0:0): RES: 41 40 b0 9e 50 40 5d 01 00...
  32. D

    Reading SMARTCTL report

    Hey everyone! I'm running FreeNAS 9.10.2-U4 and my setup includes 3 4TB WD Red Edition (NAS version @5400rpm). Today I got the following email and a critical error: CRITICAL: Aug. 1, 2017, 8:09 p.m. - Device: /dev/ada1, Self-Test Log error count increased from 0 to 1 It seems that one of the...
  33. A

    Harddrive wont start smartd/serial is too long

    Not sure where the best place to post this is as this is my first post. I cannot get the smart service to start. I have tried enabling it from the gui and shell with no joy. I fould that smart does not seem to be enabled for drive da0. I tried starting it vi shell with this command smartctl...
  34. Vrakfall

    Errors on sectors of a drive, now unreadable and S.M.A.R.T. seems to say the drive is OK-ish.

    Hello ! So, a few days ago (let's not talk about the numerous months I was shamefully ignoring the errors) I saw that one of my 3 main drives stopped working completely. By that I mean there's not a single write/read on it for a long time and the volume says it's `unavailable`. Hopefully, it's...
  35. S

    Help with SMART results

    Hello everyone, This week I received a critical alert because of an "unrecoverable error in one or more devices": http://illumos.org/msg/ZFS-8000-9P After a scrub, ada1 showed 11 checksum errors so I ran a long SMART test. These are the results: # smartctl -a /dev/ada1 smartctl 6.5...
  36. S

    Festplatten Spindown bzw. Einstellungen

    Mich würde es mal Interessieren wie Ihr s.m.a.r.t. bei euren Platten einstellt , ich habe 3 WD RED 2TB als Raid im Nas und weiss nicht so recht wie ich das sinvoll einstellen soll . Es wird ja abgeraten die Platten runter zu fahren also Spindown . Was ist am besten bzw. vernünftigsten , die...
  37. T

    SOLVED Unable to reset Current_Pending_Sector (SMART)

    Update: I ended up RMAing the drive as it was *just* within the 3 year WD Red warranty (last month). Included the SMART error log. No questions asked. Also got a spare one to prevent a similar lengthy downtime in the future. And finally I made sure all drives were selected in the (short/long)...
  38. Alan W. Smtih

    BIOS Storage Configuration settings for ASRock C2750D4I

    I'm setting up a new FreeNAS 9.10 build on an ASRock C2750D4I motherboard. The default BIOS settings under `Advanced -> Storage Configuration` are: ~ ~ ~ ~ I have two questions: 1. The `Hard Disk S.M.A.R.T.` needs to be switched to `Enabled`, right? 2. Are there any other...
  39. J

    Currently unreadable (pending) sectors - Extended offline Completed without error

    I'm a bit lost here. I'm getting Device: /dev/ada4, 1 Currently unreadable (pending) sectors So I ran a Long SMART test and followed it up with a Scrub of my volume. I've done this twice now and I'm still being told there is unreadable sectors. === START OF INFORMATION SECTION === Model...
  40. Jacopx

    SOLVED Pending sector

    Buongiorno a tutti! ;) I have a problem with a disk of my RAID-Z2, are some months the there are 5 pending sectors and I have tried to solve this problem in several ways but without success. This are the SMART results: smartctl 6.5 2016-05-07 r4318 [FreeBSD 10.3-STABLE amd64] (local build)...
  41. prototype0815

    Scrubs - SMART - Snapshot notwendig oder überflüssig mit Non-ECC RAM?

    Hey folks, ich bin gerade am einrichten meines Servers und hab zu den oben genannten Tasks bzw. Tests ein paar Fragen. Wie einige wissen habe ich ein Consumer Board mit Non-ECC RAM, aber es ist dennoch besser dies nochmal zu erwähnen. Scrubs für die Boot-Platte. In FreeNAS zu finden unter...
  42. IceBoosteR

    HDD Load Cycles, Spindown and disk access

    Hello Community, I have my FreeNAS system for a while now, and i am wondering a little bit about the hdd access and spindown for them. I also have a question for the load cyle count. First of all, I have 4 WD Red with 4TB, SMART attributes are looking like this: D# ATTRIBUTE_NAME FLAG VALUE...
  43. D

    DEFAULT SMART Scheduling

    Preface.... This may be a dumb question.... Ok, I have used 9.2.1.5, 9.2.1.8, 9.3, and am now running the most current version of 9.10.1-U4. My hardware is beyond recommended specs. I have looked for a few days now for this exact question and cant seem to find a specific answer (again, maybe...
  44. M

    Automatische Mail mit Smartbericht und anderen Infos..

    Funktioniert eigentlich das Script in den HowTo`s mit dem man automatiscjh MAils versenden kann mit Smart-Infos und anderen Systeminformationen auch mit der aktuellen 9.10er Version von Freenas? Hab mich durch das englische HowTo gekämpft, will aber nichts kaputmachen. Vielleicht gibt es ja...
  45. E

    Failed SMART self-check, BACK UP DATA NOW! but no apparent errors logged

    Hi, Woke up this morning with an alert from my freenas telling me this: smartd[2943]: Device: /dev/ada2, FAILED SMART self-check. BACK UP DATA NOW! Allright, lets check what´s up. SMART results for drive: smartctl -a /dev/ada2 smartctl 6.5 2016-05-07 r4318 [FreeBSD 10.3-STABLE amd64] (local...
  46. J

    HDD Power Off Retract Count going up regularly

    Hi, I recently installed FreeNAS 9.10 on a HP MicroServer Gen 8 with two Seagate Barracuda 7200.14 1TB disks in a ZFS mirror configuration. All is fine except that in the SMART data I can see that the emergency retract count is going up for both drives each time I turn the server on/off even...
  47. Clinderw

    Interpreting Smart Results

    Hello, I understand that ID 5, 197 and 198 should all be zero values. Anything in these fields are indicators of a pending drive failure and that I can RMA the device if I see those numbers cropping up. I have a drive that keeps sending me an email error 'Device: /dev/ada0, Self-Test Log error...
  48. danb35

    SOLVED Why didn't I get a warning on this?

    So last night I had an apparent glitch in my server--one of my drives dropped offline, then came back online a few minutes later. I got an email alert that the pool was degraded, and another that it was resilvering. After four minutes, the disk was resilvered and the pool is fine. When I got...
  49. Bidule0hm

    Scripts to report SMART, ZPool and UPS status, HDD/CPU T°, HDD identification and backup the config

    I wanted to share my scripts because I think I'm not the only one who wants to monitor his FreeNAS server a bit more closely and in a more personalized way than the automatic nightly emails would do. Please note that you're the only one responsible of what you do in the CLI so don't blame me if...
Top